Results
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging or tubing stock.
This SAE Recommended Practice establishes minimum performance requirements for trucks, buses, truck-tractors, full trailers, and semitrailers with gross vehicle weight ratings greater than 4540 kg (10 000 lb) with regard to: a Vehicle classification b Vehicle load c Percent grade d Application force
All safety glazing materials used in motor vehicles and motor vehicle equipment operating on land highways should comply with the requirements of the American National Standard, ANSI/SAE Z-26.1. The American National Standard for Safety Glazing Materials for Glazing Motor Vehicles and Motor Vehicle Equipment Operating on Land Highways—Safety Standard, ANSI/SAE Z-26.1-1996 is the latest complete updated version and is referred to hereafter as “the safety standard.” This SAE Recommended Practice is not intended to preclude references to any governmental law, ordinance, or regulation which might apply to the glazing of motor vehicles and motor vehicle equipment operating on land highways.
Limited to the commercial aerospace industry where a request is made for a PO to have Direct Delivery Authorization (DDA), which includes an Appropriate Arrangement (AA) between the PO and the Design Organization (DO). In this process the DO is responsible for ensuring the continuous updating of design and airworthiness data to the PO, whilst the PO is responsible for assurance that the manufactured article conforms to approved design and airworthiness data. The PO is responsible to provide airworthiness release documentation.
This document and the EUROCAE equivalent, ED-107, provides detailed information, guidance, and methods in support of the Federal Aviation Administration (FAA) Advisory Circular (AC) 20-158 and to the European Union Aviation Safety Agency (EASA) AMC 20-158. AC 20-158 provides a means, but not the only means, for demonstrating compliance with Title 14 of the Code of Federal Regulations (14 CFR) 23.1308 (Amendment 57 and lower), 23.2520 (Amendment 64 and higher), 25.1317, 27.1317, 29.1317, and applicable FAA HIRF special conditions addressing HIRF Protection. AMC 20-158 is applicable to Certification Specifications CS 23.1308 (Amendment 4 and lower), 23.2520 (Amendment 5 and higher), 25.1317, 27.1317, and 29.1317. It should be noted that this document is neither mandatory nor regulatory in nature and does not constitute a regulation or legal interpretation of the regulation. Therefore, an applicant may elect to establish an alternative method of compliance that is acceptable to the
This SAE Recommended Practice is prepared as a guideline to improve and maintain the quality of remanufactured automotive products. Installation of remanufactured or rebuilt products is often an economical way to repair a vehicle even though they may not fully be equivalent to original equipment parts. Before processing any part, a remanufacturer should determine if the original design and present condition of the core are suitable for remanufacturing, so as to provide durable operation of the part as well as acceptable performance when installed in a vehicle. The remanufacturer should also carefully consider the safety aspects of the product and any recommendations of the original manufacturer related to remanufacturing or rebuilding their product.
This specification covers a corrosion and heat-resistant steel in the form of sheet, strip, and plate.
This SAE Aerospace Standard (AS) offers gland details for a 0.364 inch (9.246 mm) cross-section gland (nominal 3/8 inch) with proposed gland lengths for compression-type seals with two backup rings over a range of 7 to 21 inches (178 to 533 mm) in diameter. The dash number system used is similar to AS568A. A 600 series has been chosen as a logical extension of AS568A, and the 625 number has been selected for the initial number, since 300 and 400 series in MIL-G-5514 and AS4716 begin with 325 and 425 sizes. Seal configurations and design are not a part of this document. This gland is for use with compression-type seals including, but not limited to, O-rings, T-rings, D-rings, cap seals, etc.
The purpose of this SAE Standard is to define a common set of thermodynamic test conditions to evaluate internal heat exchangers for use with R-134a and R-1234yf refrigerants in mobile air-conditioning systems. This SAE Standard can be used to test actual vehicle IHX designs or standardized IHX samples, which can be used for comparison based on a common length and shape.
This specification covers a magnesium alloy in the form of sand castings.
The intent of this specification is for the procurement of the material listed on the QPL and, therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program shall refer to the Quality Assurance section of the base specification, AMS3961. All material qualification and equivalency data has been archived and is available for review upon request. Contact the CMH-17 Secretariat (www.cmh17.org) for additional information.
This specification covers a corrosion and heat resistant nickel alloy in the form of sheet and strip.
This specification covers an aluminum alloy in the form of foil.
This specification covers three types of rubber having good resistance to high and low temperature and hydrazine type propellants, but poor resistance to hydrocarbon oils or solvents. Hydrazines are hazardous chemicals. See “Dangerous Properties of Industrial Materials” by N. Irving Sax.
This specification covers bearings of a tin alloy cast on one or both faces of a steel or bronze backing.
This specification covers the general requirements for aluminum and aluminum alloy plate and sheet. Specific requirements for plate and sheet of a particular alloy are covered by the applicable detail specification (See 6.3).
This specification covers the specific requirements for seamless tube drawn from aluminum alloy 5086.
This specification covers one type of glass cloth impregnated with a heat-reactive, thermosetting, solution-addition-type PMR-15 polyimide resin system, supplied in the form of continuous rolls of full width cloth or slit tape.
This specification covers a single-component, heat-reactive, thermosetting aromatic system which thermally cures to form a polyimide polymer structure.
This specification covers a corrosion and heat-resistant cobalt alloy in the form of welding wire.
This specification covers the engineering requirements for heat treatment of magnesium alloy castings and for parts machined from castings.
This specification covers a magnesium alloy in the form of sand castings.
This specification covers an aluminum alloy powder metallurgy product in the form of round extrusions up to 3.5 inches (89 mm) in diameter and rectangular and other solid extrusions up to 10 square inches (64.5 cm2) in cross-sectional area. The maximum extrusion length is 100 inches (2.5 m).
This SAE Standard pertains to off-road, self-propelled work machines as defined in categories one through five of SAE J1116. It is intended to provide engineers and designers with information in order that access openings provided in equipment and machinery for purposes of inspection, adjustment, and maintenance are made large enough for the intended function by the person in the field or shop.
This specification covers a palladium-silver alloy in the form of round wire 0.004 to 0.080 inch (0.10 to 2.03 mm), inclusive, in nominal diameter (see 8.5).
The content of ARP6328 contains guidance for implementing processes used for risk identification, mitigation, detection, avoidance, disposition, and reporting of counterfeit electrical, electronic, and electromechanical (EEE) parts and assemblies in accordance with AS5553 Revision D. This document may also be used in conjunction with other revisions of AS5553. This document retains guidance contained in the base document of AS5553, updated as appropriate to reflect current practices. This is not intended to stand alone, supersede, or cancel requirements found in other quality management system documents, requirements imposed by contracting authorities, or applicable laws and regulations unless an authorized exemption/variance has been obtained.
Items per page:
50
1 – 50 of 221567