Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers one grade of commercially pure titanium in the form of wire for welding filler metal (see 8.5).
This specification covers a titanium alloy in the form of bars, wire, forgings, and flash-welded rings up through 3.999 inches (101.57 mm), inclusive, and stock for forging, flash-welded rings, or heading (see 8.6).
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing up to 5.000 inches (127.00 mm), inclusive, in nominal diameter or least thickness between parallel sides (bars, rods, wire, profiles) or nominal wall thickness (tubing) (see 8.5).
This specification covers a titanium alloy in the form of welding wire (see 8.5).
This specification covers an aluminum alloy in the form of plate 0.250 to 4.000 inches (6.35 to 102.0 mm), inclusive, in nominal thickness (see 8.5).
The verification matrix (VM) in this slash sheet is intended for use to establish compliance to AS6174A. This slash sheet is applicable to AS6174A. Nothing in this slash sheet, however, supersedes applicable laws and regulations, unless a specific exemption has been obtained through judicial/legal channels.
The intent of this standard is to establish a framework to assure that all evaporators conforming to its requirements demonstrate an acceptable health and safety environment for vehicle occupants as determined from the completed risk assessment. R-744 and low pressure (i.e., non-transcritical refrigerants with a critical temperature between 85 and 120 °C) mobile air conditioning (MAC) refrigerant evaporators shall meet the testing and labeling requirements of this standard. SAE J639 contains a list of all refrigerants considered acceptable for use in mobile thermal systems for which this standard applies when the refrigerant is used in a direct expansion architecture. SAE J639 also requires an assessment to be performed to minimize reasonable risks in MAC systems. The evaporator (as designed and manufactured) shall be part of that risk assessment, and it is the responsibility of the vehicle manufacturer to ensure all relevant aspects of the evaporator are included. It is the
This specification covers an aluminum alloy in the form of rolled or cold-finished bars, rods, wire, and flash-welded rings and of stock for flash-welded rings.
This specification covers a titanium alloy in the form of sheet, strip, and plate on product 0.008 to 3.000 inches (0.20 to 76.20 mm), inclusive, in thickness (see 8.6).
This specification covers a titanium alloy in the form of pre-alloyed powder.
This specification covers a cobalt alloy in the form of wire, rod, strip, foil, and powder and a viscous mixture (paste) of the powder in a suitable binder.
The specification covers a titanium alloy in the form of wire (see 8.5).
This specification covers a titanium alloy in the form of wire for welding filler metal (see 8.5).
This specification covers an aluminum alloy in the form of honeycomb core in a non-hexagonal, flexible cell configuration with the core being treated for increased corrosion resistance and furnished only in the expanded form (see 8.5).
This specification covers a palladium-silver alloy in the form of round wire 0.004 to 0.080 inch (0.10 to 2.03 mm), inclusive, in nominal diameter (see 8.5).
This SAE Standard applies to lead-acid 12 V heavy-duty storage batteries as described in SAE J537 and SAE J930 for uses in starting, lighting, and ignition (SLI) applications on motor vehicles and/or off-road machines. These applications have some of the following characteristics: High levels of power are required to start the vehicle’s internal combustion engine. The need to supply this power limits the maximum depth of discharge to a fraction of the total capacity of the battery. The battery must be maintained at a charge level sufficient to perform this primary function by the vehicle’s voltage-regulated charging system. The vehicle’s engine powers a voltage-regulated charging system that limits the charging voltage when spinning at sufficient speed and when total loads do not exceed its output limits. The battery is subject to deeper discharging than a typical automotive application as a result of the following conditions: High daily hours of use High numbers of starts per day
This SAE Recommended Practice describes the recommended methods for testing flexible harness coverings for use on ground vehicle electrical distribution systems. It shall apply to all tapes, extruded tube, and textile tube.
This practice provides a method for evaluating microhardness and microstructure very close (0.002 inch (0.051 mm) or less) to the surface of a disk specimen. Specific accept/reject criteria for partial decarburization (3.7.1), inadvertent carburization/nitriding (3.7.3), total decarburization/intergranular oxidation (3.8), and other characteristics evaluated are to be found in the applicable specification where this ARP is referenced.
This SAE Aerospace Standard (AS) covers any protective system that serves the stated purpose.
This SAE Recommended Practice provides a taxonomy of terms related to local and regional on-demand and shared mobility services (including ground, aviation, and maritime) and their enabling technologies. Functional definitions for shared modes (both fleet sharing and ride services), services, business models, and mobility applications are defined in this SAE Recommended Practice. This SAE Recommended Practice also provides a taxonomy of related terms and definitions. Though public transport is part of shared mobility, it is not included in this SAE Recommended Practice because its definition is well-established and documented. This document does not provide specifications or otherwise impose requirements on on-demand and shared mobility.
This standard defines a color index system used by, but not limited to, Government activities in a format suitable for color identification, color selection, color matching, and quality control inspection. It also describes the designation and use of color media that is available to conduct these activities. Use of the color index referenced in this standard is intended to promote standardization and consistency in the color of items produced for Government use. Color media is described as follows: Color Chip Representation, Fan Deck: Suitable for color identification and selection. Color Chip Representation, Color Book: Suitable for color identification and selection. Precise Color Matching, Individual Color Chips: Suitable for color matching and quality control inspection purposes. Precise Color Matching, Set of Color Chips: Suitable for color matching and quality control inspection purposes.
AMS6885/2 gives specific information about the qualification program for unidirectional carbon fiber tape epoxy repair prepreg capable of curing under vacuum for repair of carbon fiber reinforced epoxy structures. The prepreg system shall include an epoxy film adhesive to be applied in a co-bonding process with the prepreg for solid laminate and sandwich bonding.
This standard is applicable to all phases of the system acquisition life cycle. It is intended for use on all programs with manufacturing content. It requires proven manufacturing management practices with the goal of delivering affordable and capable systems to the extent that it is invoked contractually. The term “organization” as used in this document refers to the company or facility that is implementing this standard, such as when imposed contractually by the customer.
This document describes the major design drivers and considerations when designing a fuel system for a large commercial aircraft. While not intended as a design manual for individual system components, it does refer out to other SAE specifications where more detail on specific components and subsystems is given. It does include examples of a number of calculations associated with sizing of fuel systems, based on those given in NAVAIR 06-5-504, as well as an appendix summarizing basic fluid mechanical equations that are key for fuel system design. It is acknowledged that most of these calculations would today be performed by modeling tools rather than by hand, but it is considered important for the designer to understand the principles. Some details specific to military aircraft are included, but it is intended that later issues of this document will include appendices that give specific considerations for military aircraft, smaller commercial aircraft, and rotorcraft. Features unique
This standard establishes the common requirements for training of DPRV personnel for use at all levels of the aerospace engine supply chain. This standard shall apply when an organization elects to delegate product release verification by contractual flow down to its suppliers (reference 9100 and 9110 standards) and to perform product acceptance on its behalf. It is intended that organizations specify their DPRV requirements through the application of AS9117. While the delegating organization will use the AS13001 standard as the baseline for establishing DPRV process and product training, it may include additional contractual training requirements to meet its specific needs. The DPRV training material was primarily developed for aerospace engine supply chain requirements. However, this standard may also be used in other aerospace industry sectors where a DPRV process requiring specific training can be of benefit.
This SAE Aerospace Standard (AS) establishes supplemental requirements for 9100 and 9145 and applies to any organization receiving it as part of a purchase order or other contractual document from a customer. AS13100 also provides details of the reference materials (RM13xxx) developed by the SAE G-22 AESQ committee and listed in Section 2 that can also be used by organizations in conjunction with this standard.
This specification covers a magnetically soft nickel-iron alloy in the form of bars, rods, forgings, mechanical tubing, and forging stock.
This document recommends standard gland design criteria and dimensions for dynamic radial O-ring seal applications specifically for engine and engine control systems operating at pressures up to a maximum of 1500 psi (10342.14 kPa) and provides recommendations for modifying these glands in special applications. There are no provisions in this document for anti-extrusion devices. NOTE: The criteria set forth here are similar to but not identical with those in MIL-G-5514 and AS4716. This document is not intended to replace MIL-G-5514 or AS4716 for hydraulic applications.
Items per page:
50
1 – 50 of 219667