Results
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging or tubing stock.
This supplement forms a part of SAE Aerospace Specification AS85421. It shall be used to identify fitting standards citing this procurement specification.
This specification establishes the requirements for a probe type self-sealing, self-aligning, non-locking coupling intended for aerospace hydraulic and cooling systems.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This SAE Standard covers fittings intended for connecting service hoses, per SAE J2196, from Mobile Air-Conditioning Systems to service equipment such as manifold gauges, vacuum pumps and air conditioning charging, recovery and recycling equipment. (Figure 1)
This specification covers the general requirements for the design and construction of air/gas compressor units (see 6.4.1). The detail requirements for a particular air compressor unit shall be as specified in the individual equipment specification for that particular air compressor unit (see 6.2).
This SAE Standard provides test procedures, requirements, and guidelines for sidemarker lamps for vehicles less than 2032 mm in overall width.
This specification covers an aluminum alloy in the form of castings (see 8.6).
This test is designed to measure the thickness of textiles, plastics, and similar materials.
This specification covers an aircraft-quality, low-alloy, heat-resistant steel in the form of bars, forgings, mechanical tubing, and forging stock.
This SAE Recommended Practice defines key terms used in the description and analysis of video based driver eye glance behavior, as well as guidance in the analysis of that data. The information provided in this practiced is intended to provide consistency for terms, definitions, and analysis techniques. This practice is to be used in laboratory, driving simulator, and on-road evaluations of how people drive, with particular emphasis on evaluating Driver Vehicle Interfaces (DVIs; e.g., in-vehicle multimedia systems, controls and displays). In terms of how such data are reduced, this version only concerns manual video-based techniques. However, even in its current form, the practice should be useful for describing the performance of automated sensors (eye trackers) and automated reduction (computer vision).
This SAE Standard specifies the general requirements and test methods for non-shielded, high-voltage ignition cable assemblies.
This specification covers a corrosion and heat resistant iron alloy in the form of covered welding electrodes.
This standard applies to pressure reducers for gaseous breathing oxygen systems and for all performance profiles without regard to particular inlet or outlet pressures. Attention is given, however, to construction requirements for reducers with maximum supply pressures to 2250 psig (155 bar) and reduced pressures of 50 to 150 psig (3.4 to 10.5 bar).
This SAE Recommended Practice describes a laboratory test procedure for measuring the acoustical performance of a system consisting of a body cavity filler material formed into a rectangular cross-section channel. Materials for this test may include both heat reactive and chemically reactive products, with or without a shelf to simulate a baffle in an application, or a combination of body cavity filler and aluminum foil to enhance the performance. These materials are commonly installed in transportation systems such as ground vehicles, and thus reduce the noise propagation through the rails, rockers, and pillar/posts. This document is intended to rank order the acoustical performance of materials for application on channels using general automotive steel, such that the effects of sealing of pinch welds in addition to the material could be easily evaluated. However, the channel is not an actual part (i.e., real life section) of the vehicle, and therefore results obtained from this study
This SAE Recommended Practice covers a procedure for evaluating plastic and multiple-layer coatings exposed to gravelometer testing (as defined in SAE J400) with an optical imaging and analysis system. The intent of the procedure is to detect, count and characterize instances of damage in the coated surface that fracture the top coat layer or penetrate through multiple layers of the coating system. It may be possible to extend this methodology of coating damage evaluation to specimens that have undergone test procedures or exposures that produce similar, discrete damage sites in the coating system. If so applied, evaluation results must be interpreted with respect to the limitations and intent implied by the original evaluation procedure and its associated rating system, if applicable.
This SAE Aerospace Recommended Practice (ARP) provides recommendations for design and test requirements for a generic “passive” side stick that could be used for fly-by wire transport and business aircraft. It addresses the following: The functions to be implemented The geometric and mechanical characteristics The mechanical and electrical interfaces The safety and certification requirements
This document sets forth design and operational recommendations concerning the human factors issues and criteria for airborne terrain separation assurance systems. The visual and aural characteristics are covered for both the alerting components and terrain depiction/situation components. The display system may contain any one or a combination of these components. Although the system functionality assumed for this document exemplifies commercial aircraft implementation, the recommendations do not exclude other fixed wing aircraft types. Because of their unique operations with respect to terrain, rotorcraft will be addressed in a separate document. The assumptions about the system that guided and bounded the recommendations included: the system will have a human centered design based on the "lessons learned" from past systems; the system is not intended to replace the Ground Proximity Warning System (GPWS) function; the system is an on-board system that is not dependent on ground
This Aerospace Recommended Practice aims at providing general utilization guidelines and calculation methods adequate to guarantee the effectiveness and ultimate load strength of tie-down/lashing arrangements performed to restrain cargo on board civil transport aircraft during flight: a Cargo loaded and tied down onto airworthiness approved air cargo pallets, themselves restrained into aircraft lower deck, main deck or upper deck cargo systems meeting the restraint requirements of air cargo pallets approved in accordance with NAS 3610 or AS36100, or b Additional tie-down on aircraft structure when necessitated by pallet maximum gross mass or centre of gravity location, or c Individual pieces of cargo, or pieces of cargo placed onto an unrestrained (“floating”) pallet into either lower deck, main deck or upper deck containerized cargo compartments of an aircraft, or d Individual pieces of load loaded in non-containerized (bulk loaded) baggage or cargo compartments.
This specification covers the requirements for heat-treatment of four classes of steel (See 1.2) and the requirements for furnace equipment, test procedures and information for heat-treating procedures, heat-treating temperatures and material (See 6.3) test procedures. This specification is applicable only to the heat treatment of raw material (See 6.3.1); it does not cover the requirements for the heat treatment of steel parts (See 3.4 and 6.3.2). This specification also describes procedures that, when followed, will produce the desired properties and material qualities within the limitations of the respective alloys tabulated in Tables 1A, 1B, 1C and 1D. Alloys other than those specifically covered herein may be heat treated using all applicable requirements of this specification.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
SAE J115 specifies the relevant ISO standards for application to safety labels for use on off-road work machines as defined in SAE J1116.
This SAE Standard gives methods for testing and evaluating performance of the SAE 100R series of hydraulic hose and hose assemblies (hose and attached end fittings) used in hydraulic fluid power systems. Specific tests and performance criteria for evaluating hose assemblies used in hydraulic service are in accordance with the requirements for hose in the respective specifications of SAE J517. This document further establishes a uniform means of testing and evaluating performance of hydraulic hose assemblies.
The test procedures and performance criteria are directed to operation and parking of agricultural tractors equipped with braking system(s) and having a maximum design speed exceeding 6 km/h. Combinations of agricultural towing machines equipped with braking systems and towed agricultural machines without braking systems are included in this SAE Standard.
Items per page:
50
1 – 50 of 221567