Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers a nitriding grade of premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. AMS6496 and AMS6497 cover UNS K23280 with other quality levels.
This specification covers a magnesium alloy in the form of investment castings (see 8.6).
This specification covers an aluminum alloy in the form of rolled or forged rings up to 6 inches (152 mm), inclusive, in thickness (see 3.3.1.1.1) and an OD to wall thickness ratio of 10 or greater (see 8.5).
This specification covers a copper-zinc alloy (brass) in the form of sheet, strip, and plate (see 8.6).
This SAE Recommend Practice establishes for passenger cars, light trucks, and multipurpose vehicles with GVW of 4500 kg (10000 pounds) or less, as defined by the EPA, and M1 category vehicles, as defined by the European Commission:
This specification covers a low-alloy steel in the form of sheet, strip, and plate 4.00 inches (101.6 mm) and under in thickness.
This specification covers an aluminum alloy in the form of sheet from 0.063 to 0.249 inch (1.60 to 6.30 mm) in nominal thickness (see 8.6).
This SAE Aerospace Recommended Practice (ARP) provides the user with standardized guidelines for the measurement of effective intensity of short pulse width strobe anticollision lights for aircraft in the laboratory, in maintenance facilities, and in the field. A common source of traceability for calibration of the measurement systems, compensation for known causes of variation in light output such as the use of colored lenses, and recommendations which minimize sources of errors and uncertainties are included in this document. Estimates of uncertainty and error sources for each class of measurement are discussed.
This specification covers a magnesium alloy in the form of investment castings (see 8.6).
This procedure describes a method of measuring the resistance to wet color transfer of materials such as textiles, leather, and composites.
The purpose of this SAE Recommended Practice is to establish a uniform laboratory procedure for securing and reporting the friction and wear characteristics of brake linings. The performance data obtained can be used for in-plant quality control by brake lining manufacturers and for the quality assessment of incoming shipments by the purchasers of brake linings.
This specification covers tungsten carbide-cobalt in the form of powder.
This specification covers a shampoo type carpet cleaner in the form of a liquid.
This specification covers a low-alloy steel in the form of welding wire. Type 2 - copper coated wire was removed from this document (see 8.4).
This specification covers the requirements for electrodeposited zinc-nickel on metal parts, including fasteners and other standard parts.
This document describes the materials, equipment, and processing techniques utilized in the fabrication of polyimide printed wiring boards. Included are recommendations for both double-sided and multilayer boards.
This specification covers an aluminum alloy in the form of sand, permanent mold, and composite mold castings with nominal wall thickness up to 1.0 inch (25 mm) or nominal weight up to 50 pounds (23 kg) (see 8.2 and 8.8).
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, wire, forgings, flash-welded rings, and extrusions 4 inches (102 mm) and under in nominal diameter or least distance between parallel sides and stock for forging or flash-welded rings.
This specification covers an aluminum alloy in the form of permanent mold castings (see 8.6).
This specification covers a titanium alloy in the form of forgings 3.000 inches (76.20 mm) and under in nominal diameter or least distance between parallel sides and 9 square inches (58 cm2) and under in cross-sectional area, and forging stock of any size (see 8.6).
This specification covers a corrosion- and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash-welded rings, and stock for forging or flash-welded rings.
This specification covers a titanium alloy in the form of bars up through 4.000 inches (101.60 mm), inclusive, in nominal diameter or least distance between parallel sides and 32 square inches (206.46 cm2) maximum cross-sectional area and stock for forging of any size (see 8.7).
This specification covers a corrosion- and heat-resistant steel in the form of welding wire.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, flash-welded rings, and stock for forging, flash-welded rings, or heading.
This specification covers a corrosion- and heat-resistant iron alloy in the form of welding wire.
This specification covers an aluminum alloy in the form of bars, rods, and wire, in the sizes shown in 3.3.3, in the “as-fabricated (F) temper.” When specified, product shall be supplied in the annealed (O) condition (see 8.6).
This specification covers the requirements for gold deposited on metal surfaces and the properties of the deposit.
This specification covers an aluminum alloy in the form of castings with nominal wall thickness up to 1.0 inch (25 mm) (see 8.8).
This specification covers a dilute aluminum/TiB2 metal matrix composite in the form of investment castings.
This specification covers two types of refined hydrocarbon compounds in the form of liquids. This specification only covers newly manufactured materials.
This specification covers an aluminum alloy in the form of castings (see 8.11).
This specification covers an iron-nickel alloy in the form of strip 0.020 to 0.250 inch (0.51 to 6.35 mm), inclusive, in thickness.
Items per page:
50
1 – 50 of 216070