This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Fastener Part Standard - Washers and Lockwashers (Inch Dimensioned)
- Ground Vehicle Standard
- J2655_201509
- Revised
Downloadable datasets available
Annotation ability available
Sector:
Issuing Committee:
Language:
English
Scope
This SAE Part Standard covers selected inch dimensioned washers and lock washers manufactured in accordance with American Society for Mechanical Engineers dimensional standards. This SAE standard covers material most often used in ship systems and equipment but its use may be applied wherever washers of the covered materials are used. This standard permits the washers to be identified and ordered by a part identification number (PIN) as defined in this standard.
-
Appendix A provides a means of establishing PINs for non-standard flat washers.
-
Appendix B establishes standards for lock plates and tab lock washers often used in Navy designs.
-
Appendix C identifies other military and non-government standards for flat washers, helical and toothed lock washers. It identifies the materials covered by each standard with a comparison of those dimensions with those SAE J2655 washers.
Rationale
ASME B18.21.1 now includes flat washers and has superseded ASME B18.22.1. All references to ASME B18.22.1.have been changed to ASME B18.21.1.
-
Section 1: Added statement on Hazardous Materials.
-
Section 2: ASME B18.21.1 has superseded ASME B18.22.1.
-
Section 3: Definitions has been inserted as a new section and all subsequent sections renumbered.
-
Section 4 (previously Section 3): Hexavalent chromium is now prohibited in all coatings. Clarified salt spray corrosion protection requirements for electrodeposited coatings. A zinc flake performance coating, Designator F, in accordance with ISO 10683 is added to provide a wider selection of acceptable zinc coatings. ISO 10683 replaces ASTM F1137 which has deleted Types II and III and ASTM F1136 previously referenced herein. .
-
Figure 1 Field 5: Designator A Aluminum has been deleted due to misidentification of the coating. Designator C has been inactivated for new design. Designators F zinc flake, ZA zinc electroplate with clear topcoat and ZC zinc electroplate with yellow topcoat have been added. Designator Z now allows either Designators ZA or ZC to be furnished.
-
Table 5 Nominal Dimensions For Fender Washers are added.
-
Table 6 (previously 5): Corrected Field 4 Designators, G1 carbon steel, S1 and S2 stainless steel and C2 brass hardness to agree with production values. G1 retains a hardness max to prevent brittle material. Corrected designator G4 alloy steel to agree with standard material availability. Added designators C1 copper alloys and N7 and N8 nickel alloys. Coatings column heading is changed from “Recommended” to “Permitted.”
-
Table 7 (previously 6): Corrected Field 4 designators S1 and S2 stainless steel hardness typographical error for toothed lock washers to agree with ASME. Added hardness value to designator C5 phosphor bronze for toothed lock washers. Added designator N7 and N8 nickel alloys.
-
Section 5: Adds guidance for CRES 316, coatings and tab type lockwashers,
-
Appendix B Lock Plates and Tab Lock Washers based upon Navy designs is added to promote standardization.
-
Minor editorial changes, clarifications and corrections made throughout.
Recommended Content
| Ground Vehicle Standard | Fastener Part Standard - Hexagon Socket, Square Head, and Slotted Headless Set Screws - Inch Dimensioned |
| Ground Vehicle Standard | Fastener Part Standard - Cap Screws, Hex, Heavy Hex and Heavy Hex Structural Bolts, and Hex Nuts (Inch Dimensioned) |
| Ground Vehicle Standard | Fastener Part Standard - Machine Screws |
Topic
Data Sets - Support Documents
| Title | Description | Download |
|---|---|---|
| Unnamed Dataset 1 | ||
| Unnamed Dataset 2 | ||
| Unnamed Dataset 3 | ||
| Unnamed Dataset 4 | ||
| Unnamed Dataset 5 | ||
| TABLE 2 | NOMINAL DIMENSIONS FOR HELICAL SPRING LOCK WASHERS | |
| TABLE 3 | NOMINAL DIMENSIONS FOR TOOTH-LOCK WASHERS | |
| TABLE 4 | NOMINAL DIMENSIONS FOR INTERNAL/EXTERNAL TOOTH LOCK WASHERS | |
| TABLE 5 | NOMINAL DIMENSIONS FOR FENDER WASHERS | |
| TABLE 6 | MATERIALS AND PIN DESIGNATORS FOR FLAT (PLAIN) WASHERS | |
| TABLE 7 | MATERIALS AND PIN DESIGNATORS FOR LOCK WASHERS | |
| TABLE A1 | DIAMETERS FOR NON-STANDARD FLAT (PLAIN) WASHERS | |
| TABLE A2 | THICKNESS TOLERANCES FOR NON-STANDARD FLAT (PLAIN) WASHERS | |
| TABLE B1 | TAB LOCK WASHER DIMENSIONS | |
| TABLE B2 | LOCK PLATE DIMENSIONS FOR ASME B16.5 FLANGES | |
| TABLE B3 | MATERIALS FOR LOCK PLATE AND TAB LOCK WASHERS | |
| TABLE C1 | FLAT (PLAIN) WASHERS - ACTIVE STANDARDS, SIZES, MATERIALS AND FINISHES | |
| TABLE C2 | FLAT (PLAIN) WASHERS - INACTIVE STANDARDS, SIZES, MATERIALS AND FINISHES | |
| TABLE C3 | HELICAL LOCK WASHERS - STANDARDS, SIZES, MATERIALS AND FINISHES | |
| TABLE C4 | TOOTH LOCK WASHERS - STANDARDS, SIZES, MATERIALS AND FINISHES |
Issuing Committee
Reference
* Redlines comparisons are available for those standards
listed in the Revision History that contain a radio button. A
redline comparison of the current version against a revision is
accomplished by selecting the radio button next to the standard and
then selecting 'compare'. At this time, Redline versions only exist
for some AMS standards. SAE will continue to add redline versioning
with ongoing updates to SAE MOBILUS.