This content is not included in your SAE MOBILUS subscription, or you are not logged in.
In-Cylinder Heat Flux in a Four Stroke, Air-Cooled, Spark-Ignited Engine with Fixed Timing
ISSN: 0148-7191, e-ISSN: 2688-3627
Published September 08, 1997 by SAE International in United States
Annotation ability available
In-cylinder heat flux, cylinder pressure, and flame arrival and position data were obtained at air fuel ratios ranging from 11 - 16 at 3060 rpm and approximately 80% load. The engine used was a single cylinder, 5 hp, fixed timing, four stroke, overhead valve, air-cooled engine. Methods of mixture preparation include that produced with the stock carburetor, and with a system designed to provide the engine with a homogeneous mixture (HMS). Heat flux was measured using a thermopile device consisting of 300 thermocouple pairs. A thin film platinum RTD was used to measure the temperature at the thermopile and correct for sensitivity of the thermopile output to thermopile temperature. Flame arrival near the sensor was found through the analysis of an ion voltage signal from a probe located next to the heat sensor.
An effort was made to identify and account for the variables which influence in-cylinder heat transfer. It was determined that with changing A/F mixtures, the dominant factor influencing heat transfer was variation in flame and pressure development which led to changes in both peak heat flux and integrated heat flux. Flame temperature variation with mixture A/F and amount of cyclic variation has a moderate affect on in-cylinder heat transfer. Amount of fuel vaporization, and mixture specific heat variations with A/F do not appear to have much effect.
Variations in average peak heat flux, location of peak heat flux, and integrated heat flux were investigated over the range of mixtures. It was found that average peak heat flux was a maximum at the peak power mixture (A/F=13.0) while the integrated heat flux was at a maximum closer to the stoichiometric mixture (14.5). Integration of the instantaneous heat flux over the entire cycle was broken down into a compression and expansion component and a gas exchange component. For compression and expansion, the integrated flux peaks at the peak power mixture and varies with A/F similarly to the average peak heat flux curve. In contrast, for gas exchange, the integrated heat flux peaks just lean of stoichiometric due to increased exhaust gas temperatures. The higher exhaust gas temperatures at these leaner mixtures is primarily a result of slower burn rates.
Correlations were obtained between the phasing of peak pressure, phasing of peak heat flux, and flame arrival. Correlation coefficients greater than 0.99 were obtained for a linear fit between average phasing of peak heat flux and average phasing of peak pressure. Another correlation investigated was between flame arrival time and time of peak heat flux. In this case, correlation coefficients greater than 0.96 were obtained.
CitationTillock, B. and Martin, J., "In-Cylinder Heat Flux in a Four Stroke, Air-Cooled, Spark-Ignited Engine with Fixed Timing," SAE Technical Paper 972708, 1997, https://doi.org/10.4271/972708.
Design and Performance of Two- and Four-Stroke Engines
Number: SP-1294; Published: 1997-09-08
Number: SP-1294; Published: 1997-09-08
- Witze, P.O. “Cycle-resolved Multipoint Ionization Probe Measurements in a Spark Ignition Engine,” SAE Paper 892099 1989
- Witze, P.O. Mendes-Lopes, J.M.C. “Direct Measurement of the Turbulent Burning Velocity in a Homogeneous-charge Engine,” Transactions of the SAE 1995 540
- Lee, A. Pyko, J.S. “Engine Misfire Detection by Ionization Current Monitoring,” SAE Paper 950003 1995
- Hager, J.M. Simmons, S. Smith, D. Onishi, S. Langley, L.W. Diller, T.E. “Experimental Performance of a Heat Flux Microsensor,” Transactions of the ASME 113 246 250 April 1991
- Bonneau, R.J. “Development of a Homogeneous Mixture System and Comparison with Carbureted Utility Engine Emissions and Performance,” Mechanical Engineering Department, University of Wisconsin Madison 1994
- Cunningham, M.J. “Effects of Mixture Preparation Parameters on Utility Engine Combustion, Performance, and Emissions,” Mechanical Engineering Department, University of Wisconsin Madison 1996
- Heywood, J.B. Internal Combustion Engine Fundamentals McGraw-Hill Publishing Company New York, N.Y. 1988
- Yang, J. Martin, J.K. “Approximate Solution - ID Energy Equation for Transient, Low-Mach Number, Compressible Turbulent Boundary Layer Flows,” ASME Journal of Heat Transfer 111 3 619 624 August 1989
- Yang, J. Martin, J.K. “Heat Transfer Predictions with High-Temperature Walls and Combustion,” SAE Paper No. 900690 1990 SAE Transactions