This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Flow and Heat Transfer Characteristics of Impinging Diesel Sprays Under Cross-Flow Conditions
Annotation ability available
Sector:
Language:
English
Abstract
The spray/wall interaction in small direct-injection diesel engines employing swirl was simulated in a bench-type experiment by a steady cross-flow of air acting on a transient diesel spray impinging normally onto a heated and unheated flat plate under atmospheric conditions. The droplet size and velocity characteristics in the radial wall-jet formed on the plate after spray impingement were investigated by phase-Doppler anemometry and the spray/wall heat transfer during impingement was measured using fast-response thermocouples. The results showed that the mechanism of secondary atomisation of the impinging droplets was altered as droplets from the approaching spray were entrained by the cross-flow, while the spray/wall heat transfer was reduced due to the lower droplet flux reaching the wall. Based on the approaching droplet velocity and size characteristics and wall temperature, an empirical correlation has been derived between the flow and heat transfer parameters.
Recommended Content
Authors
Citation
Arcoumanis, C. and Cutter, P., "Flow and Heat Transfer Characteristics of Impinging Diesel Sprays Under Cross-Flow Conditions," SAE Technical Paper 950448, 1995, https://doi.org/10.4271/950448.Also In
References
- Wachters, L.H.J. Westerling, N.A.J. “The Heat Transfer from a Hot Wall to Impinging Water Drops in the Spheroidal State,” Chem. Eng. Sci. 21 1046 1056 1966
- Pedersen, C.O. “An Experimental Study of the Dynamic Behaviour and Heat Transfer Characteristics of Water Droplets Impinging on a Heated Surface,” Int. J. Heat Mass Transfer 13 369 381 1970
- Choi, K.J. Yao, S.C. “Mechanisms of Film Boiling Heat Transfer to Normally Impacting Spray,” Int. J. Heat Mass Transfer 30 2 311 318 1987
- Naber, J.D. Farrell, P.V. “Hydrodynamics of Droplet Impingement on a Heated Surface,” SAE Paper 930919 1993
- Senda, J. Yamada, K. Fujimoto, H. Miki, H. “The Heat-Transfer Characteristics of a Small Droplet Impinging on a Hot Surface,” JSME Int, J. 31 1 105 111 1988
- Katsura, N. Saito, M. Senda, J. Fujimoto, H. “Characteristics of a Diesel Spray Impinging on a Flat Wall,” SAE Paper 890264 1989
- Brunello, G. Callera, S. Coghe, A. Cossali, G.E. Gamma, F. “LDV and PDA Analysis of Spray-Wall Interaction,” 5th Int. Conf. on Liquid Atomisation and Spray Systems (ICLASS 91) Gaithersburg U.S.A 1991
- Cossali, G.E. Coghe, A. Brunello, G. “Effects of Spray-Wall Interaction on Air Entrainment in a Transient Diesel Spray,” SAE Paper 930920 1993
- Özdemϊr, I.B. Whitelaw, J.H. “Impingement of an Unsteady Two-Phase Jet on Unheated and Heated Flat Plates,” J. Fluid Mech. 252 499 523 1993
- Senda, J. Fukami, Y. Tanabe, Y. Fujimoto, H. “Visualization of Evaporative Diesel Spray Impinging Upon Wall Surface by Exciplex Fluorescence Method,” SAE Paper 920578 1992
- Wolf, R.S. Cheng, W.K. “Heat Transfer Characteristics of Impinging Diesel Sprays,” SAE Paper 890439 1989
- Senda, J. Fujimoto, H. Yamamoto, K. “Heat Flux Between Impinged Diesel Spray and Flat Wall,” SAE Paper 912460 1991
- Kamimoto, T. Kobori, S. Hong Noh, S. Enomoto, Y. “Effects of Flame Motion and Temperature on Local Wall Heat Transfer in a Rapid Compression-Expansion Machine Simulating Diesel Combustion,” SAE Paper 922208 1992
- Arcoumanis, C. Chang, J.-C. “Spray/Wall Interaction and Implications for Heat Transfer,” IMechE Seminar on Diesel Fuel Injection Systems IMechE London 1992
- Arcoumanis. C. Chang, J.-C. “Heat Transfer Between a Heated Plate and an Impinging Transient Diesel Spray,” Exp. Fluids 16 105 119 1993
- Arcoumanis, C. Chang, J.-C. “Flow and Heat Transfer Characteristics of Impinging Transient Diesel Sprays,” SAE Paper 940678 1994
- Bosch, W. “The Fuel Rate Indicator: A New Measuring Instrument for Display of rhe Characteristics of Individual Injection,” SAE Paper 660749 1966
- Bachalo, W.D. Houser, M.J. “Development of the Phase-Doppler Spray Analyzer for Liquid Drop Size and Velocity Characterisations,” 20 th AIAA-SAE-ASME Joint Propulsion Conference Cincinnati, Ohio 1984
- Bachalo, W.D. Brena del la Rosa, A. Sankar, S.V. “Diagnostics for Fuel Spray Characterization,” Combustion Measurements Chigier N. Hemisphere 1991
- Lefebvre, A.H. Atomization and Sprays Hemisphere, New York 1989
- Tate, R.W. “Some Problems Associated with the Accurate Representation of Droplet Size Distributions,” 2 nd Int. Conf. on Liquid Atomisation and Spray Systems Madison, Wisconsin 1982
- NANMAC Temperature Handbook vol. VI NANMAC Corporation Framingham, Mass., USA 1989
- Beckwith, T.G. Buck, N.L. Marangoni, R.D. Mechanical Measurements 3rd Addison-Wesley 1982
- Arcoumanis, C. Hadjiapostolou, A. Whitelaw, J.H. “Flow and Combustion in a Hydra Direct-injection Diesel Engine,” SAE Paper 910177 1991
- Taylor, A.M.K.P. “Optically-Based Measurement Techniques for Dispersed Two-Phase Flows,” Combusting Flow Diagnostics Durao D.F.G. et al. Kluwer Academic Publishers Netherlands 1992
- Hardalupas, Y. Taylor, A.M.K.P. Whitelaw, J.H. “Characteristics of the Spray from a Diesel Injector,” Int. J. Multiphase Flow 18 2 159 179 1992
- Brunello, G. Coghe, A. Cossali, G.E. Gamma, F. “Characterisation of Transient Spray Structure in Cross-Flows,” 5 th Int. Symp on Application of Laser Techniques to Fluid Mechanics Lisbon, Portugal 1990
- Arcoumanis, C. Cutter, P.A. “Diesel Spray Development and Spray/Wall Interaction Under Cross-Flow Conditions,” 11 th European Conference of ILASS-Europe on Atomisation and Sprays Nümberg, Germany March 20th -23rd 1995
- Ladommatos, N. “Mechanisms of Heat Transfer to Liquid Films in the Manifold of Port-Injected Petrol Engines,” Proc. Instn. Mech Engrs. 207 211 222 1993