This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Experimental Analysis of Fuel and Injector Body Temperature Effect on the Hydraulic Behavior of Latest Generation Common Rail Injection Systems
Technical Paper
2018-01-0282
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
The present paper describes the effect of thermal conditions on the hydraulic behavior of Diesel common rail injectors, with a particular focus on low temperatures for fuel and injector body. The actual injection system thermal state can significantly influence both the injected quantity and the injection shape, requiring proper amendments to the base engine calibration in order to preserve the combustion efficiency and pollutant emissions levels. In particular, the introduction of the RDE (Real Driving Emission) test cycle widens the effective ambient temperature range for the homologation cycle, this way stressing the importance of the thermal effects analysis. An experimental test bench was developed in order to characterize the injector in an engine-like configuration, i.e. fuel pump, piping, common rail, pressure control system and injectors. One of the injectors is used for the measurement of injection rate time profile by means of a Zeuch method-based injection analyzer, mean injected volume per shot and dynamic pressure time-history at pump outlet and injector inlet. The fuel temperature, measured at the fuel pump inlet, and the injector body temperature are independently conditioned in a range between −10 °C and 90 °C. Latest generation common rail injectors - featuring the first a pressure-balanced pilot stage, the other a three-way valve pilot stage respectively - were tested over a wide range of thermal conditions as combination of fuel and injector body temperatures, injection pressure level (up to 2000 bar), and injection strategies (solo-main, pilot-main and main-post injection patterns). The experimental results showed a strong effect of thermal conditions on the injector hydraulics. The injected volume can be varied up to 30% compared to the reference operating condition (Tfuel = 40 °C, Tbody = 90 °C). The injection rate analysis evidenced that the injector closure timing can be seriously affected by the system thermal state, while the nozzle steady flow is typically less influenced by the fuel and injector body temperature in the examined range. It was also evidenced a different temperature effect for different pilot stage architectures. In one case the temperature reduction led to an injection volume decrease and in the other case, comparable differences where observed but with a completely opposite trend.
Recommended Content
| Technical Paper | Vacuum EGR Valve Actuator Model |
| Technical Paper | “All Electric” Controls and Accessories for Ground Vehicle Gas Turbine Propulsion Systems |
Authors
Topic
Citation
Cavicchi, A., Postrioti, L., Pesce, F., and Ferrara, U., "Experimental Analysis of Fuel and Injector Body Temperature Effect on the Hydraulic Behavior of Latest Generation Common Rail Injection Systems," SAE Technical Paper 2018-01-0282, 2018, https://doi.org/10.4271/2018-01-0282.Also In
References
- Mohan , B. , Yang , W. , and Kiang Chou , S. Fuel Injection Strategies for Performance Improvement and Emissions Reduction in Compression Ignition Engines-A Review Renewable and Sustainable Energy Reviews 28 664 676 2013
- Roberts , A. , Brooks , R. , and Shipway , P. Internal Combustion Engine Cold-Start Efficiency: A Review of the Problem, Causes and Potential Solutions Energy Conversion and Management 82 327 350 2014
- Weilenmann , M. , Soltic , P. , Saxer , C. , Forss , A.M. et al. Regulated and Nonregulated Diesel and Gasoline Cold Start Emissions at Different Temperatures Atmospheric Environment 39 13 2433 2441 2005
- Mathis , U. , Mohr , M. , and Forss , A.M. Comprehensive Particle Characterization of Modern Gasoline and Diesel Passenger Cars at Low Ambient Temperatures Atmospheric Environment 39 1 107 117 2005
- Weilenmann , M. , Favez , J.Y. , and Alvarez , R. Cold-Start Emissions of Modern Passenger Cars at Different Low Ambient Temperatures and Their Evolution over Vehicle Legislation Categories Atmospheric Environment 43 15 2419 2429 2009
- Bielaczyc , P. , Szczotka , A. , and Woodburn , J. The Effect of a Low Ambient Temperature on the Cold-Start Emissions and Fuel Consumption of Passenger Cars Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering 225 9 1253 1264 2011
- Dardiotis , C. , Martini , G. , Marotta , A. , and Manfredi , U. Low-Temperature Cold-Start Gaseous Emissions of Late Technology Passenger Cars Applied Energy 111 468 478 2013
- Varella , R.A. , Duarte , G. , Baptista , P. , Villafuerte , P.M. et al. Analysis of the Influence of Outdoor Temperature in Vehicle Cold-Start Operation Following EU Real Driving Emission Test Procedure SAE International Journal of Commercial Vehicles 10 2017 10.4271/2017-24-0140
- Dernotte , J. , Hespel , C. , Foucher , F. , Houille , S. et al. Influence of Physical Fuel Properties on the Injection Rate in a Diesel Injector Fuel 96 153 160 2012
- Seykens , X.L.J. , Somers , L.M.T. , and Baert , R.S.G. Modelling of Common Rail Fuel Injection System and Influence of Fluid Properties on Injection Process Proceedings of VAFSEP 6 9 2004
- Desantes , J.M. , Payri , R. , García , A. , and Manin , J. Experimental Study of Biodiesel Blends’ Effects on Diesel Injection Processes Energy & Fuels 23 6 3227 3235 2009
- Kazancev , K. , Makareviciene , V. , Paulauskas , V. , and Janulis , P. Cold Flow Properties of Fuel Mixtures Containing Biodiesel Derived from Animal Fatty Waste European Journal of Lipid Science and Technology 108 9 753 758 2006
- Tinprabath , P. , Hespel , C. , Chanchaona , S. , & Foucher , F. Influence of Biodiesel and Diesel Fuel Blends on the Injection Rate and Spray Injection under Cold Conditions 26th Annual Conference on Liquid Atomization and Spray System 2014
- Payri , R. , Salvador , F.J. , Gimeno , J. , and Bracho , G. Effect of Fuel Properties on Diesel Spray Development in Extreme Cold Conditions Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering 222 9 1743 1753 2008
- Vergnes , C. , Foucher , F. , and Mounaim-Rousselle , C. Discharge Coefficients for a Diesel Injector During Cold Starting Conditions Atomization and Sprays 19 7 621 631 2009
- Wang , Z. , Ding , H. , Wyszynski , M.L. , Tian , J. et al. Experimental Study on Diesel Fuel Injection Characteristics under Cold Start Conditions with Single and Split Injection Strategies Fuel Processing Technology 131 213 222 2015
- Salvador , F.J. , Gimeno , J. , Carreres , M. , and Crialesi-Esposito , M. Fuel Temperature Influence on the Performance of a Last Generation Common-Rail Diesel Ballistic Injector. Part I: Experimental Mass Flow Rate Measurements and Discussion Energy Conversion and Management 114 364 375 2016
- Zeuch , W. MTZ 344 349 1961
- Postrioti , L. , Buitoni , G. , Pesce , F.C. , and Ciaravino , C. Zeuch Method-Based Injection Rate Analysis of a Common-Rail System Operated with Advanced Injection Strategies Fuel 128 188 198 2014 10.1016/j.fuel.2014.03.006
- Piano , A. , Boccardo , G. , Millo , F. , Cavicchi , A. et al. Experimental and Numerical Assessment of Multi-event Injection Strategies in a Solenoid Common-Rail Injector SAE International Journal of Engines 10 2129 2140 2017 10.4271/2017-24-0012
- Catania , A.E. , Ferrari , A. , Manno , M. , and Spessa , E. Experimental Investigation of Dynamics Effects on Multiple-Injection Common Rail System Performance Journal of Engineering for Gas Turbines and Power 130 3 032806 2008
- Postrioti , L. , Cavicchi , A. , Paolino , D. , Guido , C. et al. An Experimental and Numerical Analysis of Pressure Pulsation Effects of a Gasoline Direct Injection System Fuel 173 8 28 2016