This content is not included in your SAE MOBILUS subscription, or you are not logged in.

The Influence of Diesel End-of-Injection Rate Shape on Combustion Recession

Journal Article
2015-01-0795
ISSN: 1946-3936, e-ISSN: 1946-3944
Published April 14, 2015 by SAE International in United States
The Influence of Diesel End-of-Injection Rate Shape on Combustion Recession
Sector:
Citation: Koci, C., Martin, G., Bazyn, T., Morrison, W. et al., "The Influence of Diesel End-of-Injection Rate Shape on Combustion Recession," SAE Int. J. Engines 8(2):647-659, 2015, https://doi.org/10.4271/2015-01-0795.
Language: English

References

  1. Erlach, H., Chmela, F., Cartellieri, W., and Herzog, P., “Pressure Modulated Injection and Its Effect on Combustion and Emissions of a HD Diesel Engine,” SAE Technical Paper 952059, 1995, doi:10.4271/952059.
  2. Miura, A. and Yuhji, Y., “Injection Rate Control of In-Line Injection Pump - Cam Design Through Injection Process Simulation,” SAE Technical Paper 950606, 1995, doi:10.4271/950606.
  3. Nishimura, T., Satoh, K., Takahashi, S., and Yokota, K., “Effects of Fuel Injection Rate on Combustion and Emission in a DI Diesel Engine,” SAE Technical Paper 981929, 1998, doi:10.4271/981929.
  4. Kohketsu, S., Tanabe, K., and Mori, K., “Flexibly Controlled Injection Rate Shape with Next Generation Common Rail System for Heavy Duty DI Diesel Engines,” SAE Technical Paper 2000-01-0705, 2000, doi:10.4271/2000-01-0705.
  5. Mahr, B., Durnholz, M., Polach, W., Grieshaber, H., “Heavy Duty Diesel Engines - The Potential of Injection Rate Shaping for Optimizing Emissions and Fuel Consumption,” presented at 21st International Engine Symposium 2000, Vienna, May 4-5, 2000.
  6. Hountalas, D., Kouremenos, D., Pariotis, E., Schwarz, V. et al., “Using a Phenomenological Multi-Zone Model to Investigate the Effect of Injection Rate Shaping on Performance and Pollutants of a DI Heavy Duty Diesel Engine,” SAE Technical Paper 2002-01-0074, 2002, doi:10.4271/2002-01-0074.
  7. Juneja, H., Ra, Y., and Reitz, R., “Optimization of Injection Rate Shape Using Active Control of Fuel Injection,” SAE Technical Paper 2004-01-0530, 2004, doi:10.4271/2004-01-0530.
  8. Seebode, J., Merker G., and Lettmann H., “Injection Strategies under the Influence of Pressure Modulation and Free Rate Shaping in Modern DI-Diesel Engines.” In CIMAC Congress. 2004.
  9. Tanabe, K., Kohketsu, S., and Nakayama, S., “Effect of Fuel Injection Rate Control on Reduction of Emissions and Fuel Consumption in a Heavy Duty DI Diesel Engine,” SAE Technical Paper 2005-01-0907, 2005, doi:10.4271/2005-01-0907.
  10. Rottmann, M., Menne, C., Pischinger, S., Luckhchoura, V. et al., “Injection Rate Shaping Investigations on a Small - Bore DI Diesel Engine,” SAE Technical Paper 2009-01-0850, 2009, doi:10.4271/2009-01-0850.
  11. Atzler, F., Kastner, O., Rotondi, R., and Weigand, A., “Multiple injection and rate shaping Part 1: Emissions reduction in passenger car Diesel engines,” SAE Technical Paper 2009-24-0004, 2009, doi:10.4271/2009-24-0004.
  12. Atzler, F., Kastner, O., Rotondi, R., and Weigand, A., “Multiple injection and rate shaping Part 2: Emissions reduction in passenger car Diesel engines Computational investigation,” SAE Technical Paper 2009-24-0012, 2009, doi:10.4271/2009-24-0012.
  13. Macian, V., Payri, R., Ruiz, S. et al., “Experimental study of the relationship between injection rate shape and Diesel ignition using a novel piezo-actuated direct-acting injector,” Applied Energy 118(1):100-113, 2014, DOI: 10.1016/j.apenergy.2013.12.025
  14. Gebert, K., Barkhimer, R., Beck, N., Wickman, D. et al., “An Evaluation of Common Rail, Hydraulically Intensified Diesel Fuel Injection System Concepts and Rate Shapes,” SAE Technical Paper 981930, 1998, doi:10.4271/981930.
  15. Wakisaka, Y. and Azetsu, A., “Effect of Fuel Injection Rate Shaping and Injection Pressure on Intermittent Spray Combustion,” SAE Technical Paper 2000-01-2793, 2000, doi:10.4271/2000-01-2793.
  16. Wakisaka, Y. and Azetsu, A., “Effects of Fuel Injection Rate Shaping on Combustion and Emission Formation in Intermittent Spray,” SAE Technical Paper 2002-01-1159, 2002, doi:10.4271/2002-01-1159.
  17. Yu, R., Kuo, T., Shahed, S., and Chang, T., “The Effect of Mixing Rate, End of Injection, and Sac Volume on Hydrocarbon Emissions from a D.I. Diesel Engine,” SAE Technical Paper 831294, 1983, doi:10.4271/831294.
  18. Musculus, M., Lachaux, T., Pickett, L., and Idicheria, C., “Endof-Injection Over-Mixing and Unburned Hydrocarbon Emissions in Low-Temperature-Combustion Diesel Engines,” SAE Technical Paper 2007-01-0907, 2007, doi:10.4271/2007-01-0907.
  19. Wickman, D., Tanin, K., Senecal, P., Reitz, R. et al., “Methods and Results from the Development of a 2600 Bar Diesel Fuel Injection System,” SAE Technical Paper 2000-01-0947, 2000, doi:10.4271/2000-01-0947.
  20. Greeves, G., Tullis, S., and Barker, B., “Advanced Two-Actuator EUI and Emission Reduction for Heavy-Duty Diesel Engines,” SAE Technical Paper 2003-01-0698, 2003, doi:10.4271/2003-01-0698.
  21. Musculus, M. and Kattke, K., “Entrainment Waves in Diesel Jets,” SAE Int. J. Engines 2(1):1170-1193, 2009, doi:10.4271/2009-01-1355.
  22. Kook, S., Pickett, L., and Musculus, M., “Influence of Diesel Injection Parameters on End-of-Injection Liquid Length Recession,” SAE Int. J. Engines 2(1):1194-1210, 2009, doi:10.4271/2009-01-1356.
  23. Malbec, L. and Bruneaux, G., “Study of Air Entrainment of Multi-hole Diesel Injection by Particle Image Velocimetry - Effect of Neighboring Jets Interaction and Transient Behavior After End of Injection.,” SAE Int. J. Engines 3(1):107-123, 2010, doi:10.4271/2010-01-0342.
  24. Eagle, W., Musculus, M., Malbec, L. and Bruneaux, G., “Measuring Transient Entrainment Waves of a Confined Vaporizing Diesel Jet,” ILASS Americas, 26th Annual Conference on Liquid Atomization and Spray Systems, Portland, OR, May, 2014.
  25. Moon, S., Matsumoto, Y., and Nishida, K., “Entrainment, Evaporation and Mixing Characteristics of Diesel Sprays around End-of-Injection,” SAE Technical Paper 2009-01-0849, 2009, doi:10.4271/2009-01-0849.
  26. Hu, B., Musculus, M., and Oefelein, J., “Large Eddy Simulation of a Transient Air Jet with Emphasis on Entrainment during Deceleration,” SAE Technical Paper 2010-01-1133, 2010, doi:10.4271/2010-01-1133.
  27. Skeen, S., Manin, J., and Pickett, L., “Simultaneous Formaldehyde PLIF and High-Speed Schlieren Imaging for Ignition Visualization in High-Pressure Spray Flames,” Proceedings of 35th International Symposium on Combustion, San Francisco, 3-8 August 2014.
  28. Bruneaux, G. and Maligne, D., “Study of the Mixing and Combustion Processes of Consecutive Short Double Diesel Injections,” SAE Int. J. Engines 2(1):1151-1169, 2009, doi:10.4271/2009-01-1352.
  29. Coldren, D. and Moncelle, M., “Advanced Technology Fuel System for Heavy Duty Diesel Engines,” SAE Technical Paper 973182, 1997, doi:10.4271/973182.
  30. Hsieh, T. and Coldren, D., “Application of Computational Fluid Dynamics for Flow Force Optimization of a High Pressure Fuel Injector Spill Valve,” SAE Technical Paper 1999-01-1537, 1999, doi:10.4271/1999-01-1537.
  31. Svensson, K. and Koci, C., “Non-classical Orifice Characterization,” SAE Technical Paper 2014-01-1431, 2014, doi:10.4271/2014-01-1431.
  32. Bazyn, T. and Martin, G.C., “Spray Combustion Measurements in a Flow-Through High Temperature, High Pressure Chamber,” ILASS Americas, 23th Annual Conference on Liquid Atomization and Spray Systems, Ventura, CA, May, 2011.
  33. Bazyn, T. and Koci, C. “The Effect of Jet Spacing on the Combustion Characteristics of Diesel Sprays,” presented at THIESEL Conference on Thermo- and Fluid Dynamic Processes in Direct Injection Engines 2014, Spain, September 9-12, 2014.

Cited By