Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers an aluminum alloy in the form of hand forgings 8 inches (203 mm) and under in nominal thickness and of forging stock (see 8.6).
This specification covers a copper-beryllium alloy in the form of bars, rods, shapes, and forgings (see 8.5).
This document applies to the development of Plans for integrating and managing COTS assemblies in electronic equipment and Systems for the commercial, military, and space markets, as well as other ADHP markets that wish to use this document. For purposes of this document, COTS assemblies are viewed as electronic assemblies such as printed wiring assemblies, disk drives, servers, printers, laptop computers, etc. There are many ways to categorize COTS assemblies1, including the following spectrum: At one end of the spectrum are COTS assemblies whose design, internal parts2, materials, configuration control, traceability, reliability, and qualification methods are at least partially controlled, or influenced, by ADHP customers (either individually or collectively) or by industry standards. An example at this end of the spectrum is a VME circuit card assembly. At the other end of the spectrum are COTS assemblies whose design, internal parts, materials, configuration control, and
This specification covers an aluminum-lithium alloy in the form of extruded profiles with a maximum cross-sectional area of 19 square inches (123 cm2) and a maximum circle size of 11 inches (279 mm) from 0.040 to 0.499 inch (1.00 to 12.50 mm) in thickness (see 8.6).
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
To establish the acceptance criteria for discontinuities as revealed by magnetic particle or liquid penetrant examination of aircraft utility parts as in 1.2.
This specification covers an aluminum alloy in the form of sheet and plate with a thickness of 0.125 to 0.499 inch (3.20 to 12.67 mm), inclusive (see 8.5).
This SAE Recommended Practice was developed primarily for passenger car and truck applications but may be used in marine, industrial, and similar applications. It addresses nonmetallic caps and both metallic and nonmetallic filler necks.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This specification covers a corrosion-resistant steel in the form of investment castings.
This specification covers columbium in the form of sheet, strip, plate, and foil.
This SAE Information Report introduces key concepts and properties of adhesives, sealants, and heat transfer materials (HTMs) and the roles they serve in present-day battery systems applications. The basic chemistry and properties of the three types of materials are summarized along with important health and environmental information. Relevant material dispense methodologies and equipment for material dispensing is reviewed. A series of representative battery applications examples employing adhesives, sealants, and HTMs is also provided with particular attention given to end-use performance.
This specification covers an aluminum alloy in the form of sheet from 0.063 to 0.249 inch (1.60 to 6.30 mm) in nominal thickness (see 8.6).
The SAE J2923 procedure is a recommended practice that applies to on-road vehicles with a GVWR below 4540 kg equipped with disc brakes.
Applies to hydraulic fluid power valves as applied to Off-Road Self-Propelled Work Machines defined in SAE J1116.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate.
This SAE Recommended Practice defines requirements for equipment and supplies to be used in measuring shot peening intensity and other surface enhancement processes. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. Guidelines for use of these items can be found in SAE J443 and SAE J2597.
This specification covers a low-alloy steel in the form of sheet, strip, and plate 4.00 inches (101.6 mm) and under in thickness.
This specification covers a copper-zinc alloy (brass) in the form of sheet, strip, and plate (see 8.6).
The purpose of this SAE Recommended Practice is to establish a uniform laboratory procedure for securing and reporting the friction and wear characteristics of brake linings. The performance data obtained can be used for in-plant quality control by brake lining manufacturers and for the quality assessment of incoming shipments by the purchasers of brake linings.
This SAE Recommend Practice establishes for passenger cars, light trucks, and multipurpose vehicles with GVW of 4500 kg (10000 pounds) or less, as defined by the EPA, and M1 category vehicles, as defined by the European Commission:
This SAE Recommended Practice describes the dynamic testing procedures required to evaluate the integrity of patient compartment interior Storage Compartments such as cabinets, drawers, or refillable supply pouch systems when exposed to a frontal, side or rear impact (i.e., a crash impact). Its purpose is to provide component manufacturers, ambulance builders, and end-users with testing procedures and, where appropriate, acceptance criteria that, to a great extent, ensure interior Storage Compartments or systems meet the same performance criteria across the industry. Descriptions of the test set-up, test instrumentation, photographic/video coverage, test fixture, and performance metrics are included.
This SAE Recommended Practice applies to all commercial, self-propelled, or towed motor vehicles which transport property or passengers in interstate commerce in which the gross vehicle weight rating or gross combination weight rating exceeds 4550 kg (10 000 lb).
This SAE Recommended Practice is intended to establish uniform procedures for developing specifications for automotive thermoplastics. It is intended for use by automotive companies and their suppliers of molded and/ or fabricated parts from thermoplastic materials.
This SAE Standard covers the minimum requirements for metric sizes of nonmetallic tubing as manufactured for use in air brake systems. Nonreinforced products are designated type A and reinforced products type B. It is not intended to cover tubing for any portion of the system that operates below -40 °C (-40 °F), above +93 °C (+200 °F), above a maximum working gage pressure of 1.0 MPa (150 psi), or in an area subject to attack by battery acid. This tubing is intended for use in the brake system for connections that maintain a basically fixed relationship between components during vehicle operation. Coiled tube assemblies required for those installations where flexing occurs are covered by this standard and SAE J1131 to the extent of setting minimum requirements on the essentially straight tube and tube fitting connections, which are used in the construction of such assemblies.2 NOTE—As all elements of SAE J1394 are being merged into SAE J844, two separate documents are no longer
This specification covers corrosion preventive compounds for spray application to vehicle body cavities
The 3D crush model can be obtained by any suitable photogrammetry method using this image set and is intended to graphically represent in photographs the shape and orientation of the damaged surface(s) relative to the undamaged, or least damaged, portion of the vehicle. The procedure is intended to provide an image set sufficient to determine, with the use of photogrammetric methodologies, the 3D location of points on the crushed surface of the damaged vehicle. Measurement of the exterior damaged surface(s) on a vehicle is a necessary step in quantifying the deformation caused by a collision and the energy dissipated by the deformation process. The energy analysis is sometimes called a crush analysis. Evaluation of the energy dissipated is useful in reconstructing the change in the velocity of the vehicles (delta-V) involved in a collision. This guideline is intended for use by investigators who do not have photogrammetry expertise, special equipment or training and may be constrained
This SAE Recommended Practice describes the test procedures for conducting quasi-static modular body strength tests for ambulance applications. Its purpose is to establish recommended test practices which standardize the procedure for Type I and Type III bodies, provide ambulance builders and end-users with testing procedures and, where appropriate, provide acceptance criteria that, to a great extent, ensures the ambulance structure meets the same performance criteria across the industry. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
This SAE Recommended Practice describes a laboratory test procedure and requirements for evaluating the characteristics of heavy-truck steering control systems under simulated driver impact conditions, as well as driver entry/egress conditions. The test procedure employs a torso-shaped body block that is impacted against the steering wheel.
This SAE Standard establishes the maximum gradient rating during hopper discharge of self-propelled, driver-operated sweepers and scrubbers as defined by SAE J2130-1 and SAE J2130-2.
This SAE Recommended Practice describes test methods for measuring and identifying the natural frequencies for the lower order modes of an inflated radial tire with a fixed spindle while expending modest effort and employing a minimum of test equipment. The methods apply to any size of radial tire so long as the test equipment is properly scaled to conduct the measurements for the intended test tire. Two types of boundary conditions are considered for the tire: unloaded and loaded against a flat surface. The test involves the performance and measurement of an input vibratory force (excitation) to the tire and the corresponding vibratory output (response). The data are suitable for use in determining parameters for road load models and for comparative evaluations of the measured properties in research and development. NOTE 1—The focus of this standard is identification and reporting of the lower order natural frequencies of the tire using a simple test procedure. While higher order
Items per page:
50
1 – 50 of 216105