Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This standard specifies the communications hardware and software requirements for fueling hydrogen surface vehicles (HSV), such as fuel cell vehicles, but may also be used where appropriate with heavy-duty vehicles (e.g., buses) and industrial trucks (e.g., forklifts) with compressed hydrogen storage. It contains a description of the communications hardware and communications protocol that may be used to refuel the HSV. The intent of this standard is to enable harmonized development and implementation of the hydrogen fueling interfaces. This standard is intended to be used in conjunction with the hydrogen fueling protocols in SAE J2601 and nozzles and receptacles conforming with SAE J2600 and ISO 17628. It may also be used with future hydrogen fueling protocols at the discretion of those fueling protocols.
This specification covers a standard acrylonitrile butadiene (NBR-H) rubber stock with medium-high acrylonitrile content in the form of molded test slabs.
This specification covers an aluminum alloy in the form of die forgings, hand forgings, and rolled rings 4 inches (102 mm) and under in nominal thickness and forging stock of any size (see 8.6).
This SAE Standard establishes the minimum construction and performance requirements for seven conductor 1/8-2/10-4/12 cable for use on trucks, trailers, and converter dollies for 12 VDC nominal applications. Where appropriate, the standard refers to two types of cables (Type F and S, described later in the standard), due to the variation in the performance demands of cables used in flexing and stationary applications. While the document’s title refers to ABS Power to differentiate the document from the SAE J1067 standard that it supersedes, the scope applies to both the primary green cable for powering ABS and lighting and the yellow auxiliary cable of the same construction.
This SAE Standard establishes the minimum performance requirements for electrical distribution systems for use in dollies and trailers in single or multiple configurations for 12 VDC nominal applications.
This SAE Recommended Practice specifies the design and/or evaluation with the specific equipment, conditions, and methods for distributorless battery ignition systems intended for use in various internal combustion engines including automotive, marine, motorcycle, and utility engine applications. The test procedures listed in this document are limited to measurements performed on a test bench only and do not include measurements made directly on engines or vehicles. This standard is not intended to supply information for battery ignition systems used in aircraft applications of any type.
This standard presents the designer with sufficient information to fully define the configuration of the connection and to determine the limits of application for given conditions.
This test method outlines a standard procedure for performing cyclic reversing load testing on oscillating sliding bearings. The wear data from these tests is to be used for qualification requirements and to establish bearing design criteria.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This specification covers established inch/pound manufacturing tolerances applicable to copper and copper alloy seamless tubing ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term “exclusive” is used to apply only to the higher figure of a specified range.
This SAE Recommended Practice defines the tests for three basic categories of pump characteristics. These are the basic functional performance tests, the pump limitation tests and the pump integrity tests. The basic functional tests included are three individual tests, with the first being for pump speed, current draw, and electrical resistance. The other two individual tests are for the deadhead pressure and the delivered fuel flow rate at the rated delivery pressure and voltage. The included tests for pump limitations are individual tests for hot fuel handling, cold magnet knockdown, load dump transient, electrical interference, and reverse flow leak. The testing for pump integrity includes individual tests for vibration, temperature cycling, internal fluid compatibility, and operational durability. These 12 individual tests provide a characterization of the particular pump. This document only addresses the in-tank-mounted, electric-motor-driven, low-pressure fuel pump itself, and
This SAE Aerospace Standard (AS) covers helical coil locking screw thread inserts made from formed wire in which the inner surface of the coil, after assembly, provides threads of standard Unified 60° form as specified on the assembly drawing. This document also covers the performance requirements of the locking feature of the insert which will retain Unified ANSI B1.1 (UN Profile) or AS8879 (UNJ Profile) external threaded parts.
This SAE Recommended Practice defines a procedure for determining shear strengths of adhesives used for bonding automotive oil metal substrates.
This specification covers a fluorosilicone rubber in the form of molded rings.
This specification covers a synthetic rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
The intent of this document is to provide recommended practices for conducting shock absorption testing of civil aircraft landing gear equipped with oleo-pneumatic shock absorbers. The primary focus is for Part 25 aircraft, but differences for Part 23, 27, and 29 aircraft are provided where appropriate.
This specification covers the specific requirements for aluminum alloy 5086 bar, rod, shapes, tube, and wire produced by extrusion.
This SAE Standard covers empty cartridges, plungers, cartridge assemblies, and nozzles which are used to package, store, and dispense single or multiple component sealants, adhesives, and other similar materials. This document defines the size, shape, composition, and function of the plastic molded cartridges, plungers, and cartridge assemblies. This document is not intended as a detailed manufacturing document.
This recommended practice provides the dimensional data for the diameters of surfaces that interface with the following tee head bolt series: AS3232 thru AS3235, MS9397 thru MS9402 and MS9432 thru MS9437, or other parts with compatible dimensions.
This SAE Aerospace Recommended Practice (ARP) describes a procedure for determining the insoluble contamination level of the downstream side of filter elements. Results of this procedure represent the particulate released from the tested filter element under the prevailing conditions of the test. The results may be used for comparative evaluation of the effectiveness of various cleaning methods or the cleanliness of elements after cleaning or as received from manufacturers.
This SAE Aerospace Information Report (AIR) describes the aspects of hydraulic system design and installation to minimize the effects of lightning. Techniques for effective electrical bonding, hydraulic system lightning protection, and lightning protection verification techniques are discussed.
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements and procedures for three classes of gas, vacuum, liquid, and low pressure (LPC) carburizing and related heat treatment of parts fabricated from carburizing grade steels. Parts made from steels other than those specified in the detail specifications may be heat treated in accordance with the applicable requirements using processing temperatures, times, and other parameters recommended by the material producer unless otherwise specified by the purchaser. This specification does not cover pack carburizing.
To provide the curved hose industry and their customers with a recommended practice for applying GD&T procedures to curved hoses and to provide generic curved hose drawings that represent the application of GD&T to typical curved hose parts. Dimensioning and Tolerancing will be in accordance with ASME Y14.5M.
This specification covers a beryllium aluminum alloy in the form of investment castings.
Items per page:
50
1 – 50 of 215889