Results
This SAE lab test procedure should be used when performing the following specialized weathering tests for wheels; Florida Exposure, QUV, Xenon and Carbon Weatherometer. In addition to these procedures, some additional post-weathering tests may be specified. Please refer to customer specifications for these requirements.
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes additional performance requirements and provides test methods and requirements to evaluate the suitability of materials intended for optical applications in motor vehicles. The tests are intended to determine physical and optical characteristics of the materials only. Performance expectations of finished assemblies, including plastic components, are to be based on tests for lighting devices, as specified in SAE Standards and Recommended Practices for motor vehicle lighting equipment. Glass and materials inclusive to the light source are not in scope for this method.
This specification covers a corrosion- and heat-resistant steel in the form of welding wire.
This specification covers quality assurance sampling and testing procedures used to determine conformance to applicable specification requirements of carbon and low-alloy steel forgings.
The purpose of this SAE Aerospace Recommended Practice (ARP) is to provide recommendations which will lead to the standardization of interior door design and operation in all transport aircraft. Interior doors are broadly classified into two main categories which include egress path doors and non-egress path doors. The scope of this ARP does not include crew rest doors, secondary barriers to the flight deck, or doors incorporated in furniture surrounding passenger seats as defined in AS6960.
These general guidelines and precautions apply to personnel operating directional drilling tracking equipment when used with horizontal directional drilling (HDD) machines as defined in ISO 21467:2023.
This specification covers an aluminum alloy in the form of Alclad sheet and plate 0.040 to 1.000 inch, inclusive (1.02 to 25.40 mm, inclusive) in nominal thickness (see 8.5).
This specification covers a heat-treatable, corrosion-resistant steel in the form of bars, wire, forgings, mechanical tubing, and stock for forging or heading.
This SAE Aerospace Recommended Practice (ARP) is written for individuals associated with the ground-level testing of large and small gas turbine engines and particularly for those who might be interested in constructing new or adding to existing engine test cell facilities.
This SAE Aerospace Standard (AS) establishes the requirements for AS3504 and AS3505 thin wall self-locking inserts made from a corrosion and heat resistant, age hardenable nickel base alloy of the type identified under the Unified Numbering System as UNS N07718.
IEEE-1394b, Interface Requirements for Military and Aerospace Vehicle Applications, establishes the requirements for the use of IEEE Std 1394™-2008 as a data bus network in military and aerospace vehicles. The portion of IEEE Std 1394™-2008 standard used by AS5643 is referred to as IEEE-1394 Beta (formerly referred to as IEEE-1394b.) It defines the concept of operations and information flow on the network. As discussed in 1.4, this specification contains extensions/restrictions to “off-the-shelf” IEEE-1394 standards and assumes the reader already has a working knowledge of IEEE-1394. This document is referred to as the “base” specification, containing the generic requirements that specify data bus characteristics, data formats, and node operation. It is important to note that this specification is not designed to be stand-alone; several requirements leave the details to the implementations and delegate the actual implementation to be specified by the network architect/integrator for a
This SAE Aerospace Standard (AS) establishes requirements for manufacturing, testing, identification, packaging, and quality of tubes for application in commercial and military aircraft wheel assemblies.
This document provides a method/procedure for specifying the properties of vulcanized elastomeric materials (natural rubber or synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications. This document covers materials that do not contain any re-use, recycled, or regrind materials unless otherwise agreed to by manufacturer and end user. The use of such materials, including maximum percent, must be specified using a “Z” suffix. This classification system covers thermoset High Consistency Elastomers (HCEs) only. Thermoplastic Elastomer (TPE) materials are classified using SAE J2558. Silicone Formed In Place Gasket (FIPG) systems such as Room Temperature Vulcanized (RTV) Silicones, and Liquid Silicone Rubber (LSR) systems are classified using ASTM F2468.
This document is intended to satisfy the data reporting requirements of standardization regulations in the United States and Europe, and any other market that may adopt similar requirements in the future. This document specifies: a Message formats for request and response messages. b Timing requirements between request messages from external test equipment and response messages from vehicles, and between those messages and subsequent request messages. c Behavior of both the vehicle and external test equipment if data is not available. d A set of diagnostic services, with corresponding content of request and response messages. e Standardized source and target addresses for clients and vehicle. This document includes capabilities required to satisfy OBD requirements for multiple regions, model years, engine types, and vehicle types. At the time of publication many regional regulations are not yet final and are expected to change in the future. This document makes no attempt to interpret
There are four basic conditions requiring the dispensing of oxygen through oxygen masks to aircraft occupants in turbine powered aircraft during flight. The following conditions are derived from the Federal Aviation Regulations (FAR) as listed in Section 2.
SAE J1939-31 network layer describes the requirements and services for network interconnection ECUs (NIECU) that enable electronic control units (ECUs) on an SAE J1939 network segment to intercommunicate with other ECUs on different network segments of the vehicle or system network. This document defines various types of NIECUs. The information in this document applies only to ECUs that are intended to provide networking services. It is not necessary for an ECU to provide any of these services in order to be compliant with the SAE J1939 protocol.
To provide a method by which to assess the cleanliness of new hydraulic fluids. The method is applicable to new mineral and synthetic hydraulic fluids - regardless of packaging. This SAE Standard is not intended as a procedure for operating equipment.
This SAE Recommended Practice describes the specific measures required to meet SAE established criteria when retrofitting CFC-12 (R-12) mobile air-conditioning (A/C) systems to HFC-134a (R-134a), with regards to fittings and labeling. This document is complete only when combined with the requirements of SAE J1657.
This SAE Standard covers specifications and performance requirements for 37-degree and 45-degree single and double flares for tube ends intended for use with SAE J512, SAE J513, SAE J514, and ISO 8434-2 connectors. The flares described in this document are intended for use with SAE metallic tube materials. Considerations such as the effects of wall thickness selection for specific working pressures, identifying the appropriate length of thread engagements for specific applications with mating connectors, and other associated criteria shall be the responsibility of the user. For applicable nominal reference working pressures for hydraulic tubing, refer to SAE J1065 and ISO 10763. In an effort to standardize within a global marketplace and ensure that companies can remain competitive in an international market, it is the intent of this document to promote the use of metric tube and connector sizes, which will: Lead to one global system. Guide users to a preferred system. Reduce
This SAE Standard applies to off-road self-propelled construction, forestry and industrial machines as listed in categories 1, 2, and 4 of SAE J1116.
This SAE Standard establishes the Tonne Kilometer Per Hour Test Procedure for off-the-road tires. This document is applicable to only those tires used on certain earthmoving machines referenced in SAE J1116.
This specification covers hand and air operated, solvent and oil spray guns.
This method is recommended for establishing breakage allowances for parts fabricated from cut lengths or blanks, or from coils processed directly into a progressive-die pressline, and is equitable to both the sheet producer and the fabricator.
This specification covers all aspects in Electrical Wiring Interconnection Systems (EWIS) from the selection through installation of wiring and wiring devices and optical cabling and termination devices used in aerospace vehicles. Aerospace vehicles include manned and unmanned airplanes, helicopters, lighter-than-air vehicles, missiles, and external pods.
Items per page:
50
1 – 50 of 215714