Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers the requirements for an electroless nickel-thallium-boron or nickel-boron deposit on various substrates.
This specification covers an aluminum alloy in the form of castings.
It is recommended that all helicopter engine development programs include an evaluation of engine starting requirements. The evaluation should include starting requirement effects on helicopter weight, cost, and mission effectiveness. The evaluation should be appropriate to the engine stage of development.
This specification covers a titanium alloy in the form of welding wire (see 8.5).
This specification covers an aluminum alloy in the form of castings (see 8.6).
This specification covers a corrosion- and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash-welded rings, and stock for forging, flash-welded rings, or heading.
This document presents design and application information which will allow optimized utilization of filter line wire and cable purchased to AS85485. Filter line wire is defined and design information is presented. The electrical and mechanical performance characteristics of the wire, along with recommended harnessing methods and techniques, are also presented.
This SAE Standard applies to machines as defined in Appendix A. Some of these machines can travel on-highway but function primarily off-highway.
This specification covers an aluminum alloy in the form of bars and rods 0.500 to 8.000 inches (12.7 to 203.2 mm) in nominal diameter or least difference between parallel sides and up to 50 square inches (322.6 cm2) in cross-sectional area (see 8.6).
This specification covers a titanium alloy in the form of sheet 0.020 to 0.1874 inch (0.51 to 4.760 mm), inclusive, in nominal thickness (see 8.6).
This specification covers a corrosion- and heat-resistant steel in the form of investment castings.
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing up to and including 1.000 inch (25.4 mm) in diameter, least thickness, or tube wall thickness (see 8.6).
SAE J1978-1 specifies a complementary set of functions to be provided by an OBD-II scan tool. These functions provide complete, efficient, and safe access to all regulated OBD (on-board diagnostic) services on any vehicle which complies to SAE J1979. The content of this document is intended to satisfy the requirements of an OBD-II scan tool as required by current U.S. OBD regulations. This document specifies: A means of establishing communications between an OBD-equipped vehicle and an OBD-II scan tool. A set of diagnostic services to be provided by an OBD-II scan tool in order to exercise the services defined in SAE J1979. In addition, SAE J1978-1 covers first generation protocol functionality defined in SAE J1979 plus automatic protocol determination for all SAE J1979/J1979-2/J1979-3 application content. The presentation of the SAE J1978 document family, where SAE J1978-1 covers first generation protocol functionality defined in SAE J1979 and protocol determination for SAE J1979, SAE
This specification covers flash-welded rings made of titanium and titanium alloys (see 8.5).
This specification covers a titanium alloy in the form of sheet 0.025 through 0.100 inch (0.63 through 2.54 mm), inclusive, in thickness (see 8.6).
This specification covers an aluminum alloy in the form of sand castings (see 8.6).
This specification covers a corrosion- and heat-resistant nickel alloy in the form of investment castings.
This specification covers a copper-beryllium alloy in the form of bars, rods, shapes, and forgings (see 8.5).
This SAE Recommended Practice was developed primarily for passenger car and truck applications but may be used in marine, industrial, and similar applications. It addresses nonmetallic caps and both metallic and nonmetallic filler necks.
This document applies to the development of Plans for integrating and managing COTS assemblies in electronic equipment and Systems for the commercial, military, and space markets, as well as other ADHP markets that wish to use this document. For purposes of this document, COTS assemblies are viewed as electronic assemblies such as printed wiring assemblies, disk drives, servers, printers, laptop computers, etc. There are many ways to categorize COTS assemblies1, including the following spectrum: At one end of the spectrum are COTS assemblies whose design, internal parts2, materials, configuration control, traceability, reliability, and qualification methods are at least partially controlled, or influenced, by ADHP customers (either individually or collectively) or by industry standards. An example at this end of the spectrum is a VME circuit card assembly. At the other end of the spectrum are COTS assemblies whose design, internal parts, materials, configuration control, and
This specification covers an aluminum alloy in the form of sheet and plate with a thickness of 0.125 to 0.499 inch (3.20 to 12.67 mm), inclusive (see 8.5).
This specification covers an aluminum alloy in the form of hand forgings 8 inches (203 mm) and under in nominal thickness and of forging stock (see 8.6).
This specification covers an aluminum-lithium alloy in the form of extruded profiles with a maximum cross-sectional area of 19 square inches (123 cm2) and a maximum circle size of 11 inches (279 mm) from 0.040 to 0.499 inch (1.00 to 12.50 mm) in thickness (see 8.6).
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
To establish the acceptance criteria for discontinuities as revealed by magnetic particle or liquid penetrant examination of aircraft utility parts as in 1.2.
This SAE Aerospace Standard provides minimum design, installation, and removal requirements for AS3319 through AS3322 studs and is applicable when specified on engineering drawings, or in procurement documents.
This SAE Recommended Practice defines the minimum performance specifications for sensors used within anthropomorphic test devices (ATDs) when performing impact tests per SAE J211. It is intended that any agency proposing to conduct tests in accordance with SAE J211 shall be able to demonstrate that the transducers they use would meet the performance requirements specified in this document.
The scope of this document is to provide the design specifications/requirements/guidelines for concrete divider surrogates that represent actual concrete dividers to the in-vehicle sensors and can be used for performance assessment of such in-vehicle sensing systems in real-world test scenarios/conditions. Therefore, this document only includes the recommended concrete divider surrogate characteristics for automotive cameras, LiDARs, and/or radars. Concrete dividers are also known as concrete barriers [1].
Almost all light trucks now are being manufactured with at least a driver side air bag and all will have dual air bags by 1998. The driving forces behind this feature are occupant safety, federal regulations, and competition in the industry. Along with the booming popularity of pickups and SUVs, they are commonly accessorized with a wide variety of products. Many accessories for four-wheel drives in particular are mounted on the front of the vehicle. These products include grille/brush guards, winches, snow plows, replacement bumpers, bicycle carriers, etc. Concerns have arisen over the compatibility of these accessories with the vehicle’s air bag system. The vehicle manufacturers are concerned because of their huge investment in design and crash test verification of the complete vehicle system and keen awareness of the federal regulations. The crushability of the front bumper and supporting structure are key elements in the system, so alterations to that area become logical concerns
This SAE Recommended Practice provides a system for classification and specification for limited number of polyamides (nylons) used in the Automotive Industry. Based upon ASTM D 4066, Classification System for Nylon Injection and Extrusion Materials (PA), it calls for additional descriptive characteristics and properties commonly used in the Automotive Industry. This document applies to natural and non-color matched black, heat-stabilized polyamide compounds only. Color matched compounds shall be defined by the proprietary OEM standards. This document allows for the use of recycled, reconstituted, and regrind materials provided that the requirements as stated in this document are met, the material has not been altered or modified to change its suitability for safe processing and use, and the material shall be identified as such.
This SAE Recommended Practice establishes uniform test procedures and certain minimum performance requirements for motor vehicle seats and seat adjusters. It is limited to tests that can be conducted on uniform test fixtures and equipment available in commercial laboratory test facilities. This practice includes a minimum requirement for horizontal forward loads encountered in vehicle forward impacts, and horizontal loads obtained by impacting the vehicle from the rear. The requirements and test procedures in this recommended practice reflect current technology and industry experience. It is intended to subject this recommended practice to a continuing review and revision as technology advances and experience is expanded.
Items per page:
50
1 – 50 of 216126