Search
Advanced Search
of the following are true

Results

Items (208,252)
This specification covers pyrometric requirements for equipment used for the thermal processing of metallic materials. Specifically, it covers temperature sensors, instrumentation, thermal processing equipment, correction factors and instrument offsets, system accuracy tests, and temperature uniformity surveys. These are necessary to ensure that parts or raw materials are heat treated in accordance with the applicable specification(s
AMS B Finishes Processes and Fluids Committee
AS22759 specification covers fluoropolymer-insulated single conductor electrical wires made with tin-coated, silver-coated, or nickel-coated conductors of copper or copper alloy as specified in the applicable detail specification. The fluoropolymer insulation may be polytetrafluoroethylene (PTFE), fluorinated ethylene propylene (FEP), polyvinylidene fluoride (PVF2), ethylene-tetrafluoroethylene copolymer (ETFE), or other Fluoropolymer resin. The fluoropolymer may be used alone or in combination with other insulation materials. These abbreviations shall be used herein. When a wire is referenced herein, it means an insulated conductor (see 7.7
AE-8D Wire and Cable Committee
This SAE Aerospace Recommended Practice (ARP) provides a framework for establishing methods and stakeholder responsibilities to ensure that seats with integrated electronic components (e.g., actuation system, reading light, inflatable restraint, in-flight entertainment equipment, etc.) meet the seat technical standard order (TSO) minimum performance standards (MPS). These agreements will allow seat suppliers to build and ship TSO-approved seats with integrated electronic components. The document presents the roles and accountabilities of the electronics manufacturer (EM), the seat supplier, and the TC/ATC/STC applicant/holder in the context of AC 21-49, Section 7.b (“Type Certification Using TSO-Approved Seat with Electronic Components Defined in TSO Design”). This document applies to all FAA seat TSOs C39( ), C127( ), etc. The document defines the roles and responsibilities of each party involved in the procurement of electronics, their integration on a TSO-approved seat, and the
Aircraft Seat Committee
This SAE Aerospace Recommended Practice (ARP) provides recommended use and installation procedures for bonded cable harness supports
AE-8A Elec Wiring and Fiber Optic Interconnect Sys Install
This specification covers a magnesium alloy in the form of sand castings
AMS D Nonferrous Alloys Committee
This specification covers a copper-nickel-tin alloy in the form of castings, made using the investment process unless sand or centrifugal processes are agreed upon by the purchaser (see 8.5
AMS D Nonferrous Alloys Committee
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet and strip up to 0.187 inch (4.75 mm) thick, inclusive, and plate up to 4.000 inches (101.6 mm) thick, inclusive
AMS F Corrosion and Heat Resistant Alloys Committee
This SAE Aerospace Information Report (AIR) is a process verification guide for evaluating implementation of key factors in repair of fiber reinforced composite bonded parts or assemblies in a repair shop, hangar, or on-wing environment. This guide is to be used in conjunction with a regulatory approved and substantiated repair and is intended to promote consistency and reliability
AMS CACRC Commercial Aircraft Composite Repair Committee
The scope of this SAE Information Report is limited to a lift crane mounted on a fixed or floating platform, lifting loads from a vessel alongside. The size of the vessel is assumed not to exceed that of a workboat as defined in 3.15
Cranes and Lifting Devices Committee
The scope of this SAE Recommended Practice is limited to cranes mounted on a fixed platform lifting loads from a vessel alongside. The size of the vessel is assumed not to exceed that of a work boat as defined in 3.14
Cranes and Lifting Devices Committee
Because of the drastic chilling involved in die casting and the fact that the solid solubilities of both aluminum and copper in zinc change with temperature, these alloys are subject to some aging changes, one of which is a dimensional change. Both of the alloys undergo a slight shrinkage after casting, which at room temperature is about two-thirds complete in five weeks. It is possible to accelerate this shrinkage by a stabilizing anneal, after which no further changes occur. The recommended stabilizing anneal is 3 to 6 h at 100 °C (212 °F), or 5 to 10 h at 85 °C (185 °F), or 10 to 20 h at 70 °C (158 °F). The time in each case is measured from the time at which the castings reach the annealing temperature. The parts may be air cooled after annealing. Such a treatment will cause a shrinkage (0.0004 in per in) of about two-thirds of the total, and the remaining shrinkage will occur at room temperature during the subsequent few weeks. Stabilizing results in a decrease in dimensions of
Metals Technical Committee
SIMILAR SPECIFICATIONS—UNS Z33521, former SAE 903, ingot is similar to ASTM B 240-79, Alloy AG40A; and UNS Z33520, former SAE 903, die casting is similar to ASTM B 86-76, Alloy AG40A. UNS Z35530, former SAE 925, ingot is similar to ASTM B 240-79, Alloy AC41A; and UNS Z35531, former SAE 925, die casting is similar to ASTM B 86-82a, Alloy AC41A
Metals Technical Committee
This SAE Standard covers the most common magnesium alloys used in wrought forms, and lists chemical composition and minimum mechanical properties for the various forms. A general indication of the usage of the various materials is also provided
Metals Technical Committee
The purpose of this SAE Recommended Practice is to establish a standardized method for determining maximum front and rear axle load ratings for industrial wheel loaders and backhoe loaders
Machine Technical Steering Committee
This recommended practice covers methods for measuring or evaluating five properties or characteristics of sintered carbide which contribute significantly to the performance of sintered carbide tools. These properties are: hardness, specific gravity, apparent porosity, structure, and grain size. They are covered under separate headings below
Metals Technical Committee
This standard is for cutting edge sections typically used in earth-moving machinery defined in SAE J1116 and ISO 6165: a Scrapers as defined in ISO 7133. b Dozers as described in ISO 6747. c Loaders as described in ISO 7131. d Graders as described in ISO 7134. Hole spacing is defined ISO 7129. Hole conformation is defined in SAE J740
MTC1, Earthmoving Machinery
This Standard provides provides names of major components peculiar to crawler tractors as defined in SAE J1057a (June, 1975). Illustrations of components are not intended to be exactly descriptive of any particular machine
MTC1, Earthmoving Machinery
This standard covers the identification, classification, and chemical composition of tool and die steels for use by engineers, metallurgists, tool designers, tool room supervisors, heat treaters, and tool makers
Metals Technical Committee
The information in this report covers data relating to SAE J438, Tool and Die Steels, and is intended as a guide to the selection of the steel best suited for the intended purpose and to provide recommended heat treatments and other data pertinent to their use. Specific requirements as to physical properties are not included because the majority of tool and die steels are either worked or given special heat treatments by the purchaser. The purchaser may or may not elect to use the accompanying data for specification purposes
Metals Technical Committee
This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration
MTC1, Earthmoving Machinery
This specification covers the requirements for producing a continuous white layer with controlled extent of porosity by means of a gaseous process, automatically controlled to maintain set values of the nitriding and carburizing potentials that determine properties of the nitrocarburized surface. Automatic control is intended to ensure repeatability of nitrogen and carbon content of the white layer which influences properties such as wear and corrosion resistance, ductility and fatigue strength
AMS B Finishes Processes and Fluids Committee
This specification covers the requirements for electrodeposition of a zinc-nickel alloy and the properties of the deposit
AMS B Finishes Processes and Fluids Committee
This SAE Standard specifies basic tolerances and dimensions for inboard propeller-shaft ends, propeller hubs and keyways for shaft sizes 3/4 in (19 mm) through 8 in (203 mm
Marine Technical Steering Committee
This SAE Recommended Practice describes the classification of off-road tires and rims for use on construction machines (see SAE J1116), defines related terminology in common use, and shows representative construction details of component parts
MTC8, Tire and Rim
This SAE Recommended Practice has been set up by Subcommittee 4 of the Off-Road Machinery Technical Committee and is primarily for directional control valves on construction and industrial machinery equipment as referenced in SAE J1116. The purpose is to establish port area to flow relationship and match valve spool eye ends in relation to rated capacity. Port connections are optional for either the 4-bolt split flange connection or the internal straight thread "O" ring connection
CTTC C1, Hydraulic Systems
This specification provides requirements and procedures for gas-pressure leak testing of parts
AMS B Finishes Processes and Fluids Committee
This SAE Recommended Practice describes a test procedure for evaluating the abrasion resistance characteristics of webbing when used in hardware of seat belt assemblies such as those described in SAE J140
Motor Vehicle Council
The comfort and fatigue of vehicle passengers is a major engineering consideration. Among the many factors involved are vibratory and auditory disturbances. Tires participate, among other elements of the vehicle, in exciting vibrations and noises. Furthermore, tires also may generate forces leading to lateral drift of the vehicle. This SAE Recommended Practice describes the design requirements for equipment to evaluate some of the characteristic excitations of passenger car and light truck tires which may cause disturbance in vehicles. The kinds of excitations treated result from nonuniformities in the structure of the tire and have their effect when a vehicle bearing the tire travels on a smooth road. This document also describes some broad aspects of the use of the equipment and lists precautionary measures that have arisen out of current experience. The intention underlying these recommendations is to establish a standardized measurement for use by the engineering community. The
Highway Tire Committee
This SAE Recommended Practice (RP) normalizes kinematic performance metrics and testing for powered standing scooters as defined in SAE J3194. Specifically, it describes: Test procedures to measure the top speed, acceleration, and deceleration performance of powered standing scooters; Test scenarios that consider initial vehicle conditions, operator anthropometry, environmental and roadway conditions, and operating domains (e.g., geofence); Relevant units, accuracy, and precision of measurement for each test; and Methods to collect and report such kinematic data. This RP does not prescribe pass/fail criteria for testing. This RP is applicable to powered standing scooters that are privately owned or available via shared- or rental-fleet operations
Powered Micromobility Vehicles Committee
This SAE Standard defines a minimum set of acceptable safety criteria for a lithium-based rechargeable battery system to be considered for use in a vehicle propulsion application as an energy storage system connected to a high voltage power train. While the objective is a safe battery system when installed into a vehicle application, this Standard is primarily focused, wherever possible, on conditions which can be evaluated utilizing the battery system alone. As this is a minimum set of criteria, it is recognized that battery system and vehicle manufacturers may have additional requirements for cells, modules, packs and systems in order to assure a safe battery system for a given application. A battery system is a completely functional energy storage system consisting of the pack(s) and necessary ancillary subsystems for physical support and enclosure, thermal management, and electronic control
Battery Safety Standards Committee
The intent of the specification is to present a functional set of requirements which define the user and hardware interfaces while providing sufficient capability to meet the misfire patterns for compliance demonstration and engineering development. Throughout this requirement, any reference to “ignition or injector control signal” is used interchangeably to infer that the effected spark ignition engine’s ignition control signal or the compression ignition engine’s injector control signal is interrupted, timing phased, or directly passed by the misfire generator. For spark ignition engines, the misfire generator behaves as a spark-defeat device which induces misfires by inhibiting normal ignition coil discharge. It does so by monitoring the vehicle’s ignition timing signals and suspends ignition coil saturation for selected cylinder firing events. The misfire generator will thereby induce engine misfire in spark ignited gasoline internal combustion engines; including rotary engines
Vehicle E E System Diagnostic Standards Committee
This SAE Standard provides testing and functional requirements to meet specified minimum performance criteria for electronic probe-type leak detectors. The equipment specified here will identify smaller refrigerant leaks when servicing motor vehicle air conditioning systems, including those engineered with improved sealing and smaller refrigerant charges to address environmental concerns and increase system efficiency. This document does not address any safety issues concerning the equipment design or use beyond that of sampling a flammable refrigerant save those described in 3.1 and 3.2 of this document. All requirements of this standard shall be verified in SAE J2911
Interior Climate Control Service Committee
This document will cover the aspects of the design and test of Class 4 through 8 electric and hybrid-electric trucks and buses for electrical safety. The document is intended to address the safety concerns of electrical systems in commercial vehicles that employ voltages greater than 60 VDC or 30 VAC RMS
Truck and Bus Powertrain Committee
This specification establishes acceptance criteria for discontinuities revealed by magnetic particle inspection of parts made from wrought, ferromagnetic materials
AMS B Finishes Processes and Fluids Committee
This Information Report along with SAE J500 and J501 is generally understood to be technically obsolete for the design of new applications. However, it is listed for those existing applications where it may be required. For the design of new applications, consult ANSI B92.1-1970—Involute Splines and Inspections Standard. [The dimensions, given in inches, apply only to soft broached holes. The shaft dimensions depend upon the shape and material of the parts, their heat treatment, and methods of machining to give the required fit. The method and amount of "breaking" sharp corners and edges also depend upon the conditions and requirements of each application. The formula for theoretical torque capacity (pressure on sides of spline) in inch-pounds per inch of bearing length (L) and at 1000 psi pressure is: The tolerances allowed are for good construction and may be readily maintained by usual broaching methods. The tolerances selected for the large and small diameters will depend upon
Materials, Processes and Parts Council
This specification covers the requirements for the application and properties of a titanium nitride coating on metal parts applied by physical vapor deposition (PVD
AMS B Finishes Processes and Fluids Committee
This SAE Recommended Practice describes a laboratory test procedure for measuring the acoustical performance of a system consisting of a body cavity filler material formed into a rectangular cross-section channel. Materials for this test may include both heat reactive and chemically reactive products, with or without a shelf to simulate a baffle in an application, or a combination of body cavity filler and aluminum foil to enhance the performance. These materials are commonly installed in transportation systems such as ground vehicles, and thus reduce the noise propagation through the rails, rockers, and pillar/posts. This document is intended to rank order the acoustical performance of materials for application on channels using general automotive steel, such that the effects of sealing of pinch welds in addition to the material could be easily evaluated. However, the channel is not an actual part (i.e., real life section) of the vehicle, and therefore results obtained from this study
Acoustical Materials Committee
The CRABI dummy was developed to evaluate small child restraint systems in automotive crash environments, in all directions of impact, with or without air bag interaction Basic anthropometry for this test device was taken from the University of Michigan Transportation Research Institute Report 85-23. Weight distribution and scaling methods for the infant were approved by the Society of Automotive (SAE) Infant Dummy Task Group. The dummy weighs 17.2 pounds and has a 26.4 inches standing or 17.3 inches sitting height. The Hybrid Ill-like neck and lumbar spine are laterally notched to reduce lateral stiffness The shoulders have flesh support for durability and human-like performance in areas where seatbelt webbing may be placed. In addition, rubber elements are used in each joint to improve biofidelity and to give the CRABI infant-like range of motion. The CRABI Six-Month-Old design meets all the SAE Infant Dummy Task Group anthropometry, biomechanical and instrumentation requirements
Dummy Testing and Equipment Committee
These test procedures apply to complete seat systems (production seats or prototypes built at the intended manufacturing quality); however, the procedures can be modified for subsystem or component level testing
Human Accom and Design Devices Stds Comm
As the number of Hydraulic Hybrid Powertrain equipped motor vehicles has increased, the number of terms, abbreviations, and acronyms which describe various components of these systems has increased. For the sake of industry standardization and to bring some order to the proliferation of such terms, abbreviations, and acronyms, the SAE Truck and Bus Hydraulic Hybrid committee prepared this document
Truck and Bus Powertrain Committee
This SAE Recommended Practice covers the design and application of a 120 VAC single phase engine based auxiliary power unit or GENSET. This document is intended to provide design direction for the single phase nominal 120 VAC as it interfaces within the truck 12 VDC battery and electrical architecture providing power to truck sleeper cab hotel loads so that they may operate with the main propulsion engine turned off
Truck and Bus Electrical Systems Committee
This Recommended Practice defines a procedure, which will aid in assessing the contaminant wear characteristics of hydraulic components. This procedure utilizes a very high level of contaminant that permits an accelerated test to determine the wear effects of contamination in a relatively short period. This recommended practice utilizes the contamination sensitivity test circuit identified in SAE J2470
Ship Fluid Systems Committee
This SAE Standard establishes a uniform procedure and performance requirements for snowmobile fuel tanks
Snowmobile Technical Committee
This SAE Standard is derived from SAE J2805 and specifies an engineering method for measuring the sound emitted by M and N category road vehicles at standstill and low speed operating conditions.. The specifications reproduce the level of sound which is generated by the principal vehicle sound sources consistent with stationary and low speed vehicle operating conditions relevant for pedestrian safety. The method is designed to meet the requirements of simplicity as far as they are consistent with reproducibility of results under the operating conditions of the vehicle. The test method requires an acoustic environment which is only obtained in an extensive open space or in special designed indoor facilities replicating the conditions of an extensive open space. Such conditions usually exist during: Measurements of vehicles for regulatory certification. Measurements at the manufacturing stage. Measurements at official testing stations. The results obtained by this method give an
Advanced Driver Assistance Systems (ADAS) Committee
This SAE Standard covers fittings, couplers, and hoses intended for connecting service hoses from mobile air-conditioning Systems to service equipment such as charging, recovery and recycling equipment. (Figure 1) This specification covers service hose fittings and couplers for MAC service equipment service hoses, per SAE J2843 and SAE J2851, from mobile air-conditioning systems to service equipment such as manifold gauges, vacuum pumps, and air-conditioning charging, recovery and recycling equipment
Interior Climate Control Service Committee
This SAE Recommended Practice was developed by SAE, and the section “Standard Classification and Specification for Service Greases” cooperatively with ASTM and NLGI. It is intended to assist those concerned with the design of automotive components, and with the selection and marketing of greases for the lubrication of certain of those components on passenger cars, trucks, and buses. The information contained herein will be helpful in understanding the terms related to properties, designations, and service applications of automotive greases
Fuels and Lubricants TC 3 Driveline and Chassis Lubrication
Items per page:
1 – 50 of 208252