Results
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry
This SAE Recommended Practice specifies graphic symbols for operator controls, gauges, tell-tales, indicators, instructions, and warning against risks in small craft and for engines and other equipment intended to be used in small craft
This SAE Recommended Practice establishes uniform procedures for testing fuel cell and hybrid fuel cell electric vehicles, excluding low speed vehicles, designed primarily for operation on the public streets, roads and highways. The procedure addresses those vehicles under test using compressed hydrogen gas supplied by an off-board source or stored and supplied as a compressed gas onboard. This practice provides standard tests that will allow for determination of fuel consumption and range based on the US Federal Emission Test Procedures, using the Urban Dynamometer Driving Schedule (UDDS) and the Highway Fuel Economy Driving Schedule (HFEDS). Chassis dynamometer test procedures are specified in this document to eliminate the test-to-test variations inherent with track testing, and to adhere to standard industry practice for fuel consumption and range testing. Communication between vehicle manufacturer and the governing authority is essential when starting official manufacturer in
This document seeks to classify all-wheel drive (AWD) architectures primarily based on the installed hardware and does not consider the implementation of the controls and software. For example, a power transfer unit (PTU) may be equipped with a clutch that is capable of torque management, but the control implementation only uses it for disconnection functions without torque management. In this SAE Recommended Practice, attention will be given to passenger cars and light trucks (through Class III). The definitions presented herein may also be applicable to heavy trucks (Class 4 through 8) and off-highway applications using more than two axles but are primarily focused on passenger cars and light trucks
This SAE Recommended Practice provides test methods and criteria for evaluating the internal cleanliness and air leakage for engine charge air coolers. This SAE Recommended Practice also provides nomenclature and terminology in common use for engine charge air coolers, related charge air cooling system components, and charge air cooling system operational performance parameters
This document derives from the Federal Motor Vehicle Safety Standards (FMVSS) 105 and 135 vehicle test protocols as single-ended inertia-dynamometer test procedures. The test sequences enable brake output measurement, friction material effectiveness, and corner performance in a controlled and repeatable environment. This SAE Document also includes optional sections for parking brake output performance for rear brakes with hydraulic or Electric Park Brakes (EPB). It applies to brake corners from vehicles covered by the FMVSS 105 and 135 when using the appropriate brake hardware and test parameters. The FMVSS 135 applies to all passenger cars and light trucks up to 3500 kg of gross vehicle weight (GVWR). The FMVSS 105 applies to all passenger cars, multi-purpose vehicles, buses, and trucks above 3500 kg of GVWR. This document does not include testing for school bus applications or vehicles equipped with hydraulic brakes with a GVWR above 4540 kg. This document does not evaluate or
To harmonize and define terminology associated with occupant protection for children for vehicle manufacturers and child restraint manufacturers in the United States and Canada
This SAE Recommended Practice establishes the test procedure, environment, instrumentation, and data analyses for comparing interior sound level of passenger cars, multipurpose vehicles, and light trucks having gross vehicle weight rating (GVWR) of 4540 kg (10 000 lb) or less. The test procedure is characterized by having fixed initial conditions (specified initial vehicle speed and gear selection at the starting point on the test site) to obtain vehicle interior sound measurement during road load operation over various road surfaces at specified constant speeds. The measurement data so derived is useful for vehicle engineering development and analysis
This SAE Aerospace Recommended Practice (ARP) addresses the general requirements for data recording procedures, packaging, and storing of elastomeric seals and seal assemblies which include an elastomeric element prior to the seal being assembled into hardware components. It applies specifically to those elastomeric seals and seal assemblies packaged shortly after manufacture. The storage period prior to installation of the elastomeric seals and seal assemblies into hardware components is commonly referred to as shelf life. The information contained in this ARP is intended to be utilized by those organizations who do not have specific requirements or recommendations already in place for the control of elastomeric seals and seal assemblies. This ARP can be specified in control, storage, and procurement documents. However, when the requirements of this document are in conflict with the customer's requirements or specifications, the requirements of the customer's detailed specification
This SAE Aerospace Standard (AS) specifies the dimensions, tolerances and size codes (dash numbers) for O-rings with a larger cross-section than those to AS568, for use in glands per MIL-G-5514 where squeeze at low temperature is often insufficient to provide a leak-tight seal
This standard establishes the dimensional and visual quality requirements, lot requirements, and packaging and labeling requirements for back-up rings machined from AMS3678/1 polytetrafluoroethylene materials for use in AS5202 ports. It shall be used for procurement purposes
There is no ISO standard equivalent to this SAE Standard. This SAE Standard identifies and defines the most commonly used terms for piston ring-groove characteristics, specifies dimensioning for groove widths, and demonstrates the methodology for calculation of piston groove root diameter. The requirements of this document apply to pistons and rings of reciprocating internal combustion engines and compressors working under analogous conditions, up to and including 200 mm diameter and 4.5 mm width for compression rings and 8.0 mm width for oil rings. The specifications in this document assume that components are measured at an ambient temperature of 20 °C (68 °F). Tolerances specified in this document represent practical functional limits and do not imply process capabilities
This SAE Recommended Practice covers the requirements for ethernet physical layer (PHY) qualification (and as applicable to other high-speed networks [i.e., Audio Bus, LVDS, Ser-Des, etc.]). Requirements stated in this document provide a minimum standard level of performance for the PHY in the IC to which all compatible ethernet communications PHY shall be designed. When the communications chipset is an ethernet switch with an integrated automotive PHY (xBASE-T1), then the testing shall include performance for all switch PHY ports as well as each controller interface. No other features in the IC are tested or qualified as part of this SAE Recommended Practice. This assures robust serial data communication among all connected devices regardless of supplier. The goal of SAE J2962-3 is to commonize approval processes of ethernet PHYs across OEMs. The intended audience includes, but is not limited to, ethernet PHY suppliers, component release engineers, and vehicle system engineers
This SAE Standard prescribes the procedure for making hardenability tests and recording results on shallow and medium hardening steels, but not deep hardening steels that will normally air harden. Included are procedures using the 25 mm (1 in) standard hardenability end-quench specimen for both medium and shallow hardening steels and subsize method for bars less than 32 mm (1-1/4 in) in diameter. Methods for determining case hardenability of carburized steels are given in SAE J1975. Any hardenability test made under other conditions than those given in this document will not be deemed standard and will be subject to agreement between supplier and user. Whenever check tests are made, all laboratories concerned must arrange to use the same alternate procedure with reference to test specimen and method of grinding for hardness testing. For routine testing of the hardenability of successive heats of steel required to have hardenability within certain limits, it is sufficient to designate
This test code describes tests for determining characteristics of hydraulic positive displacement pumps used on off-road self-propelled work machines as referenced in SAE J1116
To determine the ability of a fuel/water separator to separate emulsified or finely dispersed water from fuels. This test method is applicable for biodiesel fuel
Items per page:
50
1 – 50 of 211041