This specification covers a titanium alloy in the form of bars up through 4.000 inches (101.60 mm) in nominal diameter or least distance between parallel sides, inclusive, forgings of thickness up through 4.000 inches (101.60 mm), inclusive, with bars and forgings having a maximum cross-sectional area of 32 square inches (204.46 cm2), and stock for forging of any size (see 8.6AMS G Titanium and Refractory Metals Committee
This specification covers an aluminum alloy in the form of sheet 0.020 to 0.128 inch (0.51 to 3.25 mm), inclusive, in nominal thickness (see 8.5AMS D Nonferrous Alloys Committee
This specification covers a silicone (MQ/VMQ) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be used for molded rings, compression seals, molded O-ring cord, and molded-in-place gaskets for aeronautical and aerospace applicationsAMS CE Elastomers Committee
This specification covers an aluminum alloy in the form of plate 1.000 to 6.000 inches (25.40 to 152.40 mm), inclusive, in nominal thickness (see 8.5AMS D Nonferrous Alloys Committee
This specification covers an aluminum alloy in the form of sheet and plate 0.017 to 2.000 inches (0.43 to 50.80 mm), inclusive, in nominal thickness (see 8.6AMS D Nonferrous Alloys Committee
This specification covers an aluminum alloy in the form of extruded rods, bars, and profiles (shapes) 0.040 to 1.500 inches (1.02 to 38.10 mm), inclusive, in thickness, and produced with maximum cross-sectional area of 23.25 square inches (15000 mm2) and a maximum circumscribing circle diameter (circle size) of 15.5 inches (394 mm) (see 2.4.1 and 8.6AMS D Nonferrous Alloys Committee
This specification covers an aluminum alloy in the form of alclad coiled sheet from 0.010 to 0.128 inch (0.25 to 3.25 mm), inclusive, in thickness supplied in the -T4 temper (see 8.5AMS D Nonferrous Alloys Committee
This specification establishes requirements for a tape that is used to perform organic coatings adhesion testingAMS G8 Aerospace Organic Coatings Committee
This specification covers a titanium alloy in the form of bars, forgings, and flash-welded rings up through 12.000 inches (304.80 mm), inclusive, in diameter or least distance between parallel sides, and stock of any size for forging or flash-welded rings. Bars, forgings, and flash-welded rings with a nominal thickness of 3.000 inches (79.20 mm) or greater shall have a maximum cross-sectional area of 113 square inches (729 cm2) (see 8.5AMS G Titanium and Refractory Metals Committee
This specification establishes nondestructive testing methods, sampling frequency, and acceptance criteria for the inspection of metal castingsAMS B Finishes Processes and Fluids Committee
This specification covers an aluminum alloy in the form of alclad sheet over 0.039 to 0.126 inches (0.99 to 3.20 mm), inclusive, in nominal thickness with a fine-grain core of ASTM No. 6 or finer (see 8.5AMS D Nonferrous Alloys Committee
This method outlines a standard procedure for performing conformity tests of bearings utilizing liners of bonded polytetrafluoroethylene (PTFE). The data from these tests shall be used to determine if the product meets the conformity requirements of the applicable specificationACBG Plain Bearing Committee
This procurement specification covers the requirements for metal tube support clamps comprising of two spring clips made of corrosion and heat resistant steel and the associated PTFE single split cushion that supports the tube. See Figure 1G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies
This SAE Aerospace Standard (AS) defines minimum performance standards (MPS) for fuel flowmeters, fuel flow indicators, and fuel flow transmitters. The fuel flow indicators and transmitters are intended for use in 14 CFR Part 23, 25, 27, and 29 aircraft equipped with reciprocating and turbine engines. Multiple function displays are not within the scope of this SAE Aerospace Standard (refer to AS6296A-4FLW Fuel Flowmeters
This SAE Standard covers complete general and dimensional specifications for flareless type of hydraulic tube fittings. These fittings are intended for general application in hydraulic systems on industrial equipment and commercial products. These fittings are capable of providing leakproof, full flow connections in hydraulic systems operating at working pressures as specified in Table 1. For any application, it is recommended that sufficient testing be conducted and reviewed by both the user and fitting manufacturer to assure that performance levels will be safe and satisfactory. Formerly, SAE J514 was organized as a single document with ten clauses, which included six sections. This revision of SAE J514 has been organized into three sections as follows: Part 1: 37-degree flared fittings Part 2: Flareless (bite type) fittings Part 3: NPTF pipe fittings and pipe unions It is important to note that this and all SAE J-documents are intended for ground vehicle use only and not intendedHydraulic Tube Fittings Committee
This procurement specification covers tubular, blind rivets fabricated from a corrosion resistant nickel-copper alloy of the type identified under the Unified Numbering System as UNS N04405, and of 52 ksi minimum shear strength for self-plugging style rivetsE-25 General Standards for Aerospace and Propulsion Systems
This technical information report (IR) presents a methodology to evaluate battery pack liquid leak tightness attributes to be used in a production line to satisfy the functional requirement for IPX7, water ingress requirement, and no sustainable coolant leakage for coolant circuits. The Equivalent Channel Method is used as a suggested production leak tightness requirement for a given battery pack design that will correlate and assure that the battery pack meets or exceeds its functional requirement. Obtaining the specific geometry of the Equivalent Channel (EC) for a given battery pack is done analytically and empirically in consideration of the product design limitations. This document is a precursor to J3277-1, which will present the practices to qualify that product leak tightness is equal or better than the maximum allowed EC for that product using applicable and commercially available leak test technologies. This document may be applied to EV and HEV battery packs as tested duringBattery Standards Testing Committee
This SAE Aerospace Information Report (AIR) lists military and industry specifications, standards, recommended practices, and information reports applicable to aerospace hydraulic and pneumatic systems and componentsA-6 Aerospace Actuation, Control and Fluid Power Systems
This procurement specification covers solid rivets and hollow end rivets made from a corrosion and heat resistant steel of the type identified under the Unified Numbering System as UNS S66286 and of 80 ksi single shear strength at room temperatureE-25 General Standards for Aerospace and Propulsion Systems
This procurement specification covers aircraft-quality solid rivets made from a corrosion resistant nickel-copper alloy of the type identified under the Unified Numbering System as UNS N04400 and of 46 ksi minimum shear strengthE-25 General Standards for Aerospace and Propulsion Systems
SAE J3078 provides test methods and criteria for the evaluation of the operator enclosure environment in earth-moving machinery as defined in ISO 6165. SAE J3078/1 gives the terms and definitions which are used in other parts of SAE J3078. It is applicable to Off-Road Self-Propelled Work Machines as defined in SAE J1116 and tractors and machinery for agriculture and forestry as defined in ANSI/ASAE S390HFTC6, Operator Accommodation
This SAE Aerospace Information Report (AIR) describes a method for assessing size dependent particle losses in a sampling and measurement system of specified geometry utilizing the non-volatile PM (nvPM) mass and number concentrations measured at the end of the sampling system.1 The penetration functions of the sampling and measurement system may be determined either by measurement or by analytic computational methods. Loss mechanisms including thermophoretic (which has a very weak size dependence) and size dependent losses are considered in this method2 along with the uncertainties due to both measurement error and the assumptions of the method. The results of this system loss assessment allow development of estimated correction factors for nvPM mass and number concentrations to account for the system losses facilitating estimation of the nvPM mass and number at the engine exhaust nozzle exit plane. As the particle losses are size dependent, the magnitude of correction factors canE-31P Particulate Matter Committee
This SAE Aerospace Information Report (AIR) describes the performance of plating’s and coatings for landing gear that potentially provide environmental compliance benefits versus the current baseline processes. The hazardous systems addressed in this version of the document include cadmium plating, chromated primers, and high VOC (volatile organic compounds) topcoats. The AIR applies to landing gear structures and mechanisms for all types of civil and military aircraft. The potential replacements apply to both Original Equipment Manufacturer (OEM) hardware and overhaul of in-service landing gearsA-5 Aerospace Landing Gear Systems Committee
This document describes the aircraft industry recommendations for a headset with integral boom microphone suitable for pilot use in all types of aircraft using conventional radio installations. This document, ARINC Characteristic 535B, is in addition to and does not supersede the older ARINC Characteristic 535A: Lightweight Headset and Boom Microphone, dated March 3, 1972Airlines Electronic Engineering Committee
This SAE Standard covers the mechanical and physical requirements for Compacted Graphite Iron (CGI) castings used in automotive and allied industries. Requirements in this document include: a Tensile Strength b Yield Strength c Elongation d Graphite MorphologyMetals Technical Committee
The scope of this SAE Information Report is to provide general information relative to the nature and use of magnetic particles for nondestructive testing. The document is not intended to provide detailed technical information, but will serve as an introduction to the theory and capabilities of magnetic particle testing, and as a guide to more extensive referencesMetals Technical Committee
The scope of this SAE Information Report is to supply the user with sufficient information so that he may decide whether acoustic emission test methods apply to his particular inspection problem. Detailed technical information can be obtained by referring to Section 2Metals Technical Committee
The heating value or heat of combustion is a measure of the energy available from the fuel. The fraction or percentage of the heat of combustion that is converted to useful work is a measure of the thermal efficiency of an engine. Thus, a knowledge of the heat of combustion of the fuel is basic to the engineering of automotive engines. This SAE Information Report provides information on the standardized procedures for determining the heat of combustion of fuels that may be used for automotive engines. The changes to SAE J1498 include: SAE Publications - Added SAE Paper 2010-01-1517 Other Publications and Sections 5, 9, and 10 - Updated ASTM alphanumeric designations and titles. Section 10 - Added discussion of a method to calculate net heating value for gasoline-ethanol blends using ASTM D3338Fuels and Lubricants TC 7 Fuels Committee
SAE J1717 is an advisory document suggesting minimum recommended testing, appearance evaluation, and protocol for specifying the recommendations with regard to Singular Unassembled Automotive Interior Trim PartsPlastics Committee
See Table 1. DAx fluids are mineral oil based, DPx fluids are polyalphaolefin based, and DEx are ester basedFuel and Lubricants TC2 Industrial Lubricants
This standard sets forth the characteristics of a terrain awareness and warning system intended for installation in aircraft with digital signal interfaces. Describes the desired operational capability of the equipment, the standards necessary to ensure interchangeability, form factor, and pin assignmentsAirlines Electronic Engineering Committee
ISO 7745 shall be used for providing detailing, operational characteristics, advantages, disadvantages, and factors affecting the choice to be made among fire-resistant fluids. HFAE, HFC, HFDR, HFDU and HETG oils are covered in this specification. HFAS, HFB and HFDS fluids are not addressedFuel and Lubricants TC2 Industrial Lubricants
This specification gives general requirements for electric devices for which the detail requirements are given by standards only, as the detail requirements for the devices are not complex enough to warrant issuance of detail specifications for themAE-7 Aerospace Electrical Power and Equipment Committee
This document describes the aircraft industry recommendations for a handheld microphone and boom microphone for use with airborne radio installations. This document, ARINC Characteristic 538C, is in addition to and does not supersede the older ARINC Characteristic 538B: Hand-Held Microphone, dated February 16, 1983Airlines Electronic Engineering Committee
This information report provides basic information on leakage testing, as applied to nondestructive testing, and affords the user sufficient information so that he may decide whether leakage testing methods apply to his particular need. Detailed references are listed in Section 2Metals Technical Committee
Test equipment practices change over time to better suit the maintenance philosophies of the airlines. This standard is an update of ARINC 602 following the introduction of new digital test equipment standards and the publication of ARINC 608A. This standard includes specific references to On-board Maintenance Systems (OMS) and Automatic test Equipment (ATE) used within the maintenance communityAirlines Electronic Engineering Committee, Avionics Maintenance Committee
This Report presents general information on over 50 alloys in which nickel either predominates or is a significant alloying element. It covers primarily wrought materials, and is not necessarily all inclusive. Values given are in most cases average or nominal, and if more precise values are required the producer(s) should be contacted. This report does not cover the so-called "superalloys," or the iron base stainless steels. Refer to SAE J467, Special Purpose Alloys, and SAE J405, Chemical Compositions of SAE Wrought Stainless Steels, respectively, for data on these alloysMetals Technical Committee
This specification covers the requirements for filled, resinous thermosetting compound and sheet pre-preg to fabricate shims for use during assembly of aircraft and marine components and partsAMS P Polymeric Materials Committee
This specification covers a polytetrafluoroethylene (PTFE) resin filled with 15% glass fiber and 5% molybdenum disulfide in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion processAMS P Polymeric Materials Committee