Results
This SAE Recommended Practice covers passive torque biasing axle and center differentials used in passenger car and light truck applications. Differentials are of the bevel gear, helical gear, and planetary types, although other configurations are possible.
This SAE Recommended Practice covers the design and application of a 120 VAC single phase engine based auxiliary power unit or GENSET. This document is intended to provide design direction for the single phase nominal 120 VAC as it interfaces within the truck 12 VDC battery and electrical architecture providing power to truck sleeper cab hotel loads so that they may operate with the main propulsion engine turned off.
This material type has resistance to hot air, but generally has poor resistance to fuels and lubricants, but usage is not limited to such applications. Each application should be considered separately. This material type has a typical service temperature range of -85 to 500 °F (-65 to 260 °C). The operating temperature range of the material is a general temperature range, but the presence of particular fluids and design parameters may modify this range. Recommendations on the material selection are based on available technical data and are offered as suggestions only. Each user should make his own tests to determine the suitability for his own particular use.
This specification provides dimensional standards for crimp type contact wire barrel design and is a replacement for MS3190. Some wire barrel designs may exist in AS39029 but are not considered approved for future use, therefore, will not appear in this specification. The crimp barrel sizes listed in this document have been standardized in AS39029 and AS22520 specifications, tools and contacts are available to support these listed sizes. These crimp barrel requirements shall be used for any contact, regardless of whether it is a standard or non-standard contact configuration. The specification lists details for three types of wire barrels: A, B, and C. Wire barrel type A is not recommended for new design. Table 4 lists each AS39029 detail sheet wire barrel type.
This SAE Aerospace Information Report (AIR) provides Nuclear, Biological and Chemical (NBC) protection considerations for environmental control system (ECS) design. It is intended to familiarize the ECS designer with the subject in order to know what information will be required to do an ECS design where NBC protection is a requirement. This is not intended to be a thorough discussion of NBC protection. Such a document would be large and would be classified. Topics of NBC protection that are more pertinent to the ECS designer are discussed in more detail. Those of peripheral interest, but of which the ECS designer should be aware are briefly discussed. Only radiological aspects of nuclear blast are discussed. The term CBR (Chemical, Biological, and Radiological) has been used to contrast with NBC to indicate that only the radiological aspects of a nuclear blast are being discussed. This is actually a more accurate term to describe the subject of this paper, but NBC has become more
This document establishes standard gland dimensions for low pressure static radial O-ring seal applications and provides recommendations for modifying these glands in special applications. No provisions are made in this document for anti-extrusion devices.
This document covers all-metal, self-locking nuts, plate nuts, and gang channel nuts made of a corrosion and heat resistant nickel alloy.
This SAE Aerospace Recommended Practice (ARP) establishes software capability guidelines for computer controlled test equipment, hereinafter referred to as automatic test equipment (ATE), for testing hydraulic components. A typical ATE system is shown in Figure 1. The items herein have been selected as potential features which may or may not be applicable to a particular application. This document does not address software development requirements, qualification procedures, or hardware design requirements, but encourages users to refer to existing documents, defined in 2.1.1, for guidance on such issues.
This standard includes ISO 9001:20152 quality management system requirements and specifies additional civil and military aviation maintenance and continuing airworthiness industry requirements, definitions, and notes. It is emphasized that the requirements specified in this standard are complementary (not alternative) to customer and applicable statutory and regulatory requirements. If there is a conflict between the requirements of this standard and customer or applicable statutory or regulatory requirements, the latter shall take precedence. This International Standard specifies requirements for a quality management system when an organization: a needs to demonstrate its ability to consistently provide products and services that meet customer and applicable statutory and regulatory requirements, and b aims to enhance customer satisfaction through the effective application of the system, including processes for improvement of the system and the assurance of conformity to customer and
The following recommendations and suggestions are made for consideration for procurement of new equipment, or modification to existing equipment where practical. Excluded from this AIR is mobile ground equipment, such as fork lift trucks and front end loaders, that have a functional requirement for simultaneous vehicle motion and accessory operation.
Items per page:
50
1 – 50 of 211878