Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers a copper-beryllium alloy in the form of bars, rods, shapes, and forgings (see 8.5).
This document applies to the development of Plans for integrating and managing COTS assemblies in electronic equipment and Systems for the commercial, military, and space markets, as well as other ADHP markets that wish to use this document. For purposes of this document, COTS assemblies are viewed as electronic assemblies such as printed wiring assemblies, disk drives, servers, printers, laptop computers, etc. There are many ways to categorize COTS assemblies1, including the following spectrum: At one end of the spectrum are COTS assemblies whose design, internal parts2, materials, configuration control, traceability, reliability, and qualification methods are at least partially controlled, or influenced, by ADHP customers (either individually or collectively) or by industry standards. An example at this end of the spectrum is a VME circuit card assembly. At the other end of the spectrum are COTS assemblies whose design, internal parts, materials, configuration control, and
This specification covers an aluminum alloy in the form of sheet and plate with a thickness of 0.125 to 0.499 inch (3.20 to 12.67 mm), inclusive (see 8.5).
This specification covers an aluminum alloy in the form of hand forgings 8 inches (203 mm) and under in nominal thickness and of forging stock (see 8.6).
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers an aluminum-lithium alloy in the form of extruded profiles with a maximum cross-sectional area of 19 square inches (123 cm2) and a maximum circle size of 11 inches (279 mm) from 0.040 to 0.499 inch (1.00 to 12.50 mm) in thickness (see 8.6).
This SAE Recommended Practice was developed primarily for passenger car and truck applications but may be used in marine, industrial, and similar applications. It addresses nonmetallic caps and both metallic and nonmetallic filler necks.
To establish the acceptance criteria for discontinuities as revealed by magnetic particle or liquid penetrant examination of aircraft utility parts as in 1.2.
This specification describes the engineering requirements for producing a non-powdery anodic coating on titanium and titanium alloys and the properties of such coatings.
This specification covers an aluminum alloy in the form of permanent mold castings (see 8.6).
This specification covers established manufacturing tolerances applicable to titanium and titanium alloy tubing. These tolerances apply to all conditions, unless otherwise noted. The term "excl" is used to apply only to the higher figure of the specified range.
This specification establishes testing methods for testing chemical composition in nickel- and cobalt-based alloys.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate.
This specification covers a corrosion-resistant steel product 8 inches (203 mm) and under in nominal diameter, thickness or for hexagons, least distance between parallel sides, and having a maximum cross-sectional area of 64 square inches (413 cm2) in the solution and precipitation heat treated (H900) condition.
This Purchasing Specification, AMS6885/3, specifies the batch release and delivery requirements for unidirectional carbon fiber tape epoxy prepreg used for repair. This specification is applicable only when the unidirectional carbon fiber tape epoxy prepreg is used as part of the repair system defined in AMS6885 and AMS6885/1. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials qualified against AMS6885 (refer to PRI-QPL-AMS6885) and shall be carried out within the responsibility of the purchaser and under control of its Quality organisation.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate 0.015 to 1.5 inches (0.38 to 38 mm) in nominal thickness.
This SAE Aerospace Information Report (AIR) provides a general description of methods for hardness testing of O-rings including factors which affect precision and comparison of results with those obtained in standard tests.
This specification covers a corrosion-resistant steel product 8 inches (203 mm) and under in nominal diameter, thickness, or for hexagons least distance between parallel sides in the solution and precipitation heat-treated (H1100) condition.
This specification covers an aluminum alloy in the form of permanent mold castings (see 8.6).
This SAE Aerospace Standard (AS) provides a standardized test procedure that can be used to evaluate material capability in a dynamic sealing application. This procedure will be utilized by applicable elastomer material specifications which are used for production of O-rings and other seals. This specification is applicable to the dynamic testing requirements for aerospace elastomer parts utilizing materials conforming to AMS7XXX series specifications, user specifications, or print on a Purchase Order (PO) that calls out this document for aerospace applications. This procedure is intended for testing NBR. Other elastomers may have different requirements which will require a separate procedure.
This material has resistance to diester-based engine oil (MIL-PRF-7808) and fuel, but usage is not limited to such applications. This material is not suitable for use in synthetic phosphate ester based hydraulic fluids (AS1241) or helicopter transmission lubricating oils (DOD-PRF-85734, MIL-PRF-32538). For gas turbine engine lubricating oils (AS5780, MIL-PRF-23699), resistance varies by class and should be evaluated individually (see Note regarding high performance oils). This material has a typical service temperature range of -70 to +392 °F (-56.7 to +200 °C) for Class 1 and Class 2 and -70 to +437 °F (-56.7 to +225 °C) for Class 3. The service temperature range of the material is a general temperature range, but the presence of particular fluids and specific design requirements may modify this range. Each application should be considered separately. It is the responsibility of the user to determine that this specification is appropriate for the environments (temperature range
This specification covers a dilute aluminum/TiB2 metal matrix composite in the form of sand castings.
This specification covers flash welded rings made of corrosion and heat-resistant austenitic steels and austenitic-type iron, nickel, or cobalt alloys, or precipitation-hardenable alloys.
This specification covers an aluminum alloy in the form of clad sheet 0.006 to 0.249 inch (0.015 to 6.32 mm), inclusive, in thickness (see 8.6).
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, and forging stock.
This specification covers one type of copper-beryllium alloy in the form of sheet and strip up to 0.188 inch (4.78 mm) in nominal thickness (see 8.7).
This specification covers a magnesium alloy in the form of sand castings (see 8.6).
This specification covers a titanium alloy in the form of bars up through 3.000 inches (76.20 mm), inclusive, in diameter or least distance between parallel sides with a maximum cross-sectional area of 10 square inches (64.5 cm2) and forging stock of any size (see 8.7).
This specification covers a 100% homopolymer of polychlorotrifluoroethylene (PCTFE) in the form of rods, sheets, and molded shapes.
This specification covers quality assurance sampling and testing procedures used to determine conformance to applicable specification requirements of carbon and low-alloy steel forgings.
This specification covers one type of carpet cleaner in the form of a liquid.
Items per page:
50
1 – 50 of 216102