Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers an aluminum alloy in the form of rolled or forged rings up to 6 inches (152 mm), inclusive, in thickness (see 3.3.1.1.1) and an OD to wall thickness ratio of 10 or greater (see 8.5).
This specification covers a magnesium alloy in the form of investment castings (see 8.6).
This specification covers a nitriding grade of premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. AMS6496 and AMS6497 cover UNS K23280 with other quality levels.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This specification covers columbium in the form of sheet, strip, plate, and foil.
This SAE Information Report introduces key concepts and properties of adhesives, sealants, and heat transfer materials (HTMs) and the roles they serve in present-day battery systems applications. The basic chemistry and properties of the three types of materials are summarized along with important health and environmental information. Relevant material dispense methodologies and equipment for material dispensing is reviewed. A series of representative battery applications examples employing adhesives, sealants, and HTMs is also provided with particular attention given to end-use performance.
The SAE J2923 procedure is a recommended practice that applies to on-road vehicles with a GVWR below 4540 kg equipped with disc brakes.
This specification covers an aluminum alloy in the form of sheet from 0.063 to 0.249 inch (1.60 to 6.30 mm) in nominal thickness (see 8.6).
This specification covers a copper-zinc alloy (brass) in the form of sheet, strip, and plate (see 8.6).
The purpose of this SAE Recommended Practice is to establish a uniform laboratory procedure for securing and reporting the friction and wear characteristics of brake linings. The performance data obtained can be used for in-plant quality control by brake lining manufacturers and for the quality assessment of incoming shipments by the purchasers of brake linings.
This SAE Recommend Practice establishes for passenger cars, light trucks, and multipurpose vehicles with GVW of 4500 kg (10000 pounds) or less, as defined by the EPA, and M1 category vehicles, as defined by the European Commission:
This specification covers a low-alloy steel in the form of sheet, strip, and plate 4.00 inches (101.6 mm) and under in thickness.
This SAE Recommended Practice defines requirements for equipment and supplies to be used in measuring shot peening intensity and other surface enhancement processes. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. Guidelines for use of these items can be found in SAE J443 and SAE J2597.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This SAE Aerospace Recommended Practice (ARP) provides the user with standardized guidelines for the measurement of effective intensity of short pulse width strobe anticollision lights for aircraft in the laboratory, in maintenance facilities, and in the field. A common source of traceability for calibration of the measurement systems, compensation for known causes of variation in light output such as the use of colored lenses, and recommendations which minimize sources of errors and uncertainties are included in this document. Estimates of uncertainty and error sources for each class of measurement are discussed.
This specification covers a magnesium alloy in the form of investment castings (see 8.6).
This SAE Recommended Practice provides definitions of common terms used in SAE Documents pertaining to motor vehicle lighting. It covers not only basic lighting terms but also terms which identify major segments of technical reports.
This document describes an inspection procedure for detecting, by use of a radiographic opaque tracer and fluoroscopy or radiography methods, flaws which have been produced as the result of cutting, machining, or drilling operations in composite or laminate structures.
This specification covers a premium aircraft-quality, corrosion-resistant steel in the form of bars, wire, forgings, flash-welded rings, and extrusions up to 12 inches (305 mm) in nominal diameter or least distance between parallel sides (thickness) in the solution heat-treated condition (see 8.4) and stock of any size for forging, flash-welded rings, or extrusions.
This document establishes the minimum curriculum requirements for training, practical assessments, and certifying composite structure repair personnel and metalbond repair personnel. It establishes criteria for the certification of personnel requiring appropriate knowledge of the technical principles underlying the composite structural repairs and/or metalbond they perform. Persons certified under this document may be eligible for licensing/certification/qualification by an appropriate authority, in addition to this industry-accepted technician certification. Teaching levels have been assigned to the curriculum to define the knowledge, skills, and abilities graduates will need to make repairs to composite or metalbond structure. Minimum hours of instruction have been provided to ensure adequate coverage of all subject matter, including lecture and laboratory. These minimums may be exceeded and may include an increase in the total number of training hours and/or increase in the teaching
This specification covers a corrosion- and heat-resistant steel in the form of bars, forgings, and forging stock.
This specification covers an aluminum alloy in the form of investment castings (see 8.6).
This SAE Aerospace Information Report (AIR) provides a general description of methods for hardness testing of O-rings including factors which affect precision and comparison of results with those obtained in standard tests.
This specification covers a titanium alloy in the form of cold rolled sheet and strip up to 0.100 inch (2.540 mm), inclusive, in thickness.
This specification covers a corrosion-resistant steel product in the solution and precipitation heat-treated (H950) condition, 12 inches (305 mm) and under in nominal diameter, thickness, or, for hexagons, least distance between parallel sides.
This specification covers a fluorosilicone (FVMQ) rubber in the form of molded rings.
This specification covers two tempers of aluminum alloy in the form of bars, rods, and wire up to 8.000 inches (203.2 mm) in nominal thickness (see 8.6).
This specification covers an aluminum alloy in the form of sheet and plate, alclad both sides, supplied in the -T361 temper.
This specification covers an aluminum alloy in the form of die castings.
This specification covers a magnesium alloy in the form of investment castings (see 8.6).
This specification covers a magnesium alloy in the form of extruded bars, rods, wire, tubing, and profiles.
This specification covers a titanium alloy in the form of bars, wire, forgings, flash-welded rings 4.000 inches (101.60 mm) and under in nominal diameter or least distance between parallel sides, and stock of any size for forging or flash-welded rings (see 8.6).
This specification covers the requirements for a manganese phosphate coating on ferrous alloys.
This specification covers the requirements for electrodeposited cadmium on metal parts.
This specification covers materials in the form of a liquid used to remove smut from aluminum surfaces treated with etch-type oxidation and corrosion removers.
This specification covers the requirements for producing brazed joints in parts made of steels, iron alloys, nickel alloys, and cobalt alloys by use of nickel alloy filler metal.
Items per page:
50
1 – 50 of 216070