Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers a 100% homopolymer of polychlorotrifluoroethylene (PCTFE) in the form of rods, sheets, and molded shapes.
This specification covers a 100% homopolymer of polychlorotrifluoroethylene (PCTFE) in the form of sheet 0.250 inch (6.35 mm) and over in thickness, rod, heavy wall tubing, and large molded and machined parts.
This SAE Recommended Practice provides procedures and methods for testing service, spring applied parking, and combination brake actuators with respect to durability, function, and environmental performance. A minimum of six test units designated A, B, C, D, E, and F are to be used to perform all tests per 1.1 and 1.2.
The scope of this document is to define a test method for performing the Compression Stress Relaxation (CSR) Test with the Automotive Standard (ASD) or HP CSR Jig using the appropriate test fixtures, configurations, and procedures. This standard defines the equipment needed, guidelines for running the test, and the format for generating the results and analyzing the data.
This specification covers a magnesium alloy in the form of plate 0.250 to 6.000 inches (6.35 to 152.40 mm), inclusive, in nominal thickness (see 8.5).
This specification covers a standard acrylonitrile butadiene (NBR-H) rubber stock with medium-high acrylonitrile content in the form of molded test slabs.
This specification covers a nitriding grade of aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. AMS6497 and AMS6498 cover UNS K23280 having other quality levels.
This method is designed to evaluate the coking propensity of synthetic ester-based aviation lubricants under two phase air-oil mist conditions as found in certain parts of a gas turbine engine, for instance, bearing chamber vent lines. Based on the results from round robin data in 2008 to 2009 from four laboratories, this method is currently intended to provide a comparison between lubricants as a research tool; it is not currently a satisfactory pass/fail test.
This SAE Standard applies to mobile, construction-type lifting cranes utilizing cantilevered boom crane structures and associated jibs (see Figure 1).
This SAE Aerospace Standard (AS) will specify what type of NVGs are required and minimum requirements for compatible crew station lighting, aircraft exterior lighting such as anti-collision lights, and position/navigation lights that are “NVG compatible.” Also, this document is intended to set standards for NVG utilization for aircraft so that special use aircraft such as the Coast Guard, Border Patrol, Air Rescue, Police Department, Medivacs, etc., will be better equipped to chase drug smugglers and catch illegal immigrants, rescue people in distress, reduce high-speed chases through city streets by police, etc. Test programs and pilot operator programs are required. For those people designing or modifying civil aircraft to be NVG compatible, the documents listed in 2.1.3 are essential.
The purpose of this SAE Aerospace Recommended Practice (ARP) is to provide the aerospace industry with recommendations concerning the minimization of stress corrosion cracking in wrought heat-treatable carbon and low-alloy steels and in austenitic, precipitation hardenable, and martensitic corrosion-resistant steels and alloys. The detailed recommendations are based on laboratory and field experience and reflect those design practices and fabrication procedures which should avoid in-service stress corrosion cracking.
This specification covers quality assurance sampling and testing procedures used to determine conformance to applicable material specifications of corrosion- and heat-resistant steel and alloy forgings.
This specification covers steel cleanliness requirements for aircraft-quality ferromagnetic steels, other than hardenable corrosion-resistant steels (refer to AMS2303), by magnetic particle inspection methods. This specification contains sampling, specimen preparation, inspection procedures, and cleanliness rating criteria (see 8.2).
This specification covers steel cleanliness requirements for special aircraft-quality ferromagnetic steels, including hardenable corrosion-resistant steels, by magnetic particle inspection methods. This specification contains sampling, sample preparation, inspection procedures, and cleanliness rating criteria (see 8.2).
Turbine engines installed in helicopters require a highly sophisticated oil system to fulfill two primary tasks: Cooling/oil supply Lubrication of rotating components (bearings, shafts, gears, etc.) While lubrication is an engine internal operation, depending on the engine oil system configuration, cooling and oil supply may require more or less design activity on the aircraft side of the engine/airframe interface for proper engine function. The necessity for engine cooling and oil supply provisions on the airframe can lead to interface problems because the helicopter manufacturer can influence engine related functions due to the design of corresponding oil system components.
This specification covers a corrosion-resistant steel in the form of investment castings.
This specification covers an aluminum alloy in the form of wire, sheet, foil, pig, grains, shot, and chips (see 8.6).
This specification covers an aluminum alloy in the form of die forgings, hand forgings, and rolled rings 4 inches (102 mm) and under in nominal thickness and forging stock of any size (see 8.6).
This specification covers a corrosion- and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash-welded rings, and stock for forging or flash-welded rings.
This document provides a summary of names commonly used throughout the industry for aircraft fuel system components. It is a thesaurus intended to aid those not familiar with the lexicon of the industry.
SCOPE IS UNAVAILABLE.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This SAE Standard provides requirements and guidance to: Develop a Materiel authenticity plan. Procure Materiel from reliable sources. Assure authenticity and conformance of procured Materiel, including methods such as certification, traceability, testing, and inspection appropriate to the Commodity/item in question. Control Materiel identified as counterfeit. Report Suspect or Counterfeit Materiel to other potential users and Authorities Having Jurisdiction.
This specification covers one weight and one strength of intermediate modulus aramid cloth.
This specification covers one weight and one strength of intermediate modulus aramid cloth.
This specification covers one width and strength of nylon tape.
This specification covers one width and strength of nylon tape.
Items per page:
50
1 – 50 of 215928