Results
The content of ARP6328 contains guidance for implementing processes used for risk identification, mitigation, detection, avoidance, disposition, and reporting of counterfeit electrical, electronic, and electromechanical (EEE) parts and assemblies in accordance with AS5553 Revision D. This document may also be used in conjunction with other revisions of AS5553. This document retains guidance contained in the base document of AS5553, updated as appropriate to reflect current practices. This is not intended to stand alone, supersede, or cancel requirements found in other quality management system documents, requirements imposed by contracting authorities, or applicable laws and regulations unless an authorized exemption/variance has been obtained.
This document describes: a The preparatory steps to test experimental Type I fluids according to AMS1424; b The recommendations for the preparation of samples for endurance time testing according to ARP5945; c A short description of the recommended field spray test; d The protocol to demonstrate that Type I fluid can be used with the Type I holdover time guidelines published by the FAA and Transport Canada, including endurance time data obtained from ARP5945; e The protocol for inclusion of Type I fluids on the FAA and Transport Canada lists of fluids; f The protocol for updating the FAA and Transport Canada lists of fluids; g The role of the SAE G-12 Aircraft Deicing Fluids Committee; h The role of the SAE G-12 Holdover Time Committee; and i The process for the publication of Type I holdover time guidelines. This document does not describe laboratory-testing procedures. This document does not include the qualification requirements for AMS1428 Type II, III, and IV fluids (these are
This information report presents recommendations on part number marking which provides for the maximum identification on bolts and nuts while ensuring adequate readability.
This SAE Recommended Practice is part of the SAE J2534-2/X_0500 set of documents that extends the SAE J2534-1_0500 API (version 05.00) specification, and defines how to implement single wire CAN (SW CAN) within the SAE J2534 API framework. This document details only the changes from SAE J2534-1_0500 and items not specifically detailed in this document are assumed to have not changed. An SAE J2534-2/1_0500 interface shall be compliant to the single wire CAN feature only when all the required functionality in this SAE Recommended Practice is implemented. Any functionality not required for compliance will be specifically marked as “optional” in this document. This document must be used in conjunction with the SAE J2534-2/BA_0500 and SAE J2534-2/RE_0500 documents.
This document applies to prognostics of aerospace propulsion systems. Its purpose is to define the meaning of prognostics in this context, explain their potential and limitations, and to provide guidelines for potential approaches for use in existing condition monitoring environments. This document also includes some examples. The current revision does not provide specific guidance on validation and verification, nor does it address implementation aspects such as computational capability or certification.
This SAE Aerospace Standard (AS) establishes a Generic Open Architecture (GOA) Framework for application independent hardware/software systems. This document defines the interface classes for the GOA Framework. Supplemental documents define the guidelines for applying the GOA Framework to specific applications.
This document describes the initial development, evolution, and use of reticulated polyurethane foam as an explosion suppression material in fuel tanks and dry bays. It provides historical data, design practice guidelines, references, laboratory test data, and service data gained from past experience. The products discussed in this document may be referred to as "Safety Foam," "Reticulated Polyurethane Foam," "Baffle and Inerting Material," or "Electrostatic Suppression Material." These generic terms for the products discussed in this document are not meant to imply any safety warranty. Each individual design application should be thoroughly proof tested prior to production installation.
This SAE Aerospace Recommended Practice (ARP) lists the lamps in Table 1 that are recommended for the type of service indicated. This list is not intended as a catalog and does not include many types that are now in use. This specification is not applicable to Solid State Lighting Lamp Assemblies (Based LED lamps). It does, however, reflect current practice.
This specification defines basic physical, chemical, and performance limits for 5 cSt grades of gas turbine engine lubricating oils used in aero and aero-derived marine and industrial applications, along with standard test methods and requirements for laboratories performing them. It also defines the quality control requirements to assure batch conformance and materials traceability and the procedures to manage and communicate changes in oil formulation and brand. This specification invokes the Performance Review Institute (PRI) product qualification process. Requests for submittal information may be made to PRI at the address in 2.1.3, referencing this specification. Products qualified to this specification are listed on a Qualified Products List (QPL) managed by PRI. Additional tests and evaluations may be required by individual OEMs before an oil is approved for use in their equipment. Approval and/or certification for use of a specific gas turbine engine oil in aero and aero
This material type has resistance to hot air, but generally has poor resistance to fuels and lubricants, but usage is not limited to such applications. Each application should be considered separately. This material type has a typical service temperature range of -85 to 500 °F (-65 to 260 °C). The operating temperature range of the material is a general temperature range, but the presence of particular fluids and design parameters may modify this range. Recommendations on the material selection are based on available technical data and are offered as suggestions only. Each user should make his own tests to determine the suitability for his own particular use.
SCOPE IS UNAVAILABLE.
This document covers all metal, castellated, self-locking nuts made from alloy steel of the types identified under the Unified Numbering System as UNS G41300 and UNS G43400.
This standard establishes the dimensional and visual quality requirements, lot requirements, and packaging and labeling requirements for O-rings machined from AMS3668 material. It shall be used for procurement purposes.
This recommended practice provides the design criteria for static elastomeric O-ring seals used specifically in engine and engine control systems. It provides axial compression (face type) groove dimensions for aerospace metric O-ring sizes specified in MA2010. The conditions considered to formulate the design criteria are also described, e.g., seal squeeze and groove volume to accommodate O-ring swell. NOTE: Tables of O-ring groove dimensions are included based on the design criteria specified herein. Dimensions in this document are in millimeters unless otherwise specified.
This document is a companion document to SAE AS4893 “Generic Open Architecture (GOA) Framework Standard” and provides an overview and rationale for SAE AS4893. The GOA Framework establishes an architectural framework to assist in the application of open systems interface standards to the design of specific hardware/software systems. The GOA Framework standard is intended for use by both system designers and system implementers in the development of open systems architectures. It is intended that domain specific guidelines be developed to provide clarification for application of the GOA Framework. The Generic Open Architecture (GOA) Framework was initially developed by the SAE to provide a framework which could be used to classify interfaces needed in airborne avionics systems. At the time of the development of the GOA Framework, development of such a classification was considered crucial to the application of open systems standards to military avionics. However, it was recognized
This design standard specifies the dimensions of the externally threaded fitting end to be assembled into an internally threaded fluid system port, using an elastomeric o-ring for sealing. Fitting end dimensions and o-ring sizes agree with ISO 7320-1985.
This SAE Aerospace Standard (AS) establishes the requirements for fluid fittings that combine both weld fitting end and 24° cone flareless fitting end connections for use in all types of fluid systems.
Items per page:
50
1 – 50 of 219718