Results
This specification covers a high temperature, compression set and fluid resistant fluorocarbon (FKM) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes for aeronautical and aerospace applications.
This specification covers a silicone (PVMQ) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
This standard covers plain and flanged sleeve bearings which are self-lubricating by incorporating polytetrafluoroethylene (PTFE) in a liner in the bore for use in a temperature range of -65 to +250 °F (-54 to +121 °C).
This standard covers all types of manually operated high pressure oxygen, cylinder shut off valves for use in commercial aircraft. It is intended that the valve shall be attached to a pressure cylinder storing oxygen under a nominal pressure of 12.76 MPa (1850 psig) at 21 °C (70 °F). Upon opening the valve, oxygen will be permitted to discharge from the storage cylinder to the valve outlet and to other downstream components of the oxygen system. It shall also be possible to recharge the cylinder through the valve.
This SAE Standard provides installation requirements, test procedures, design guidelines, and performance requirements for side turn signal lamps for vehicles less than 12 m in length.
This specification covers a corrosion- and heat-resistant steel in the form of seamless tubing.
This SAE Recommended Practice (RP) describes a test method for determination of heavy truck (Class VI, VII, and VIII) tire force and moment properties under straight-line braking conditions. The properties are acquired as functions of normal force and slip ratio using a sequence specified in this practice. At each normal force increment, the slip ratio is continually changed by application of a braking torque ramp. The data are suitable for use in vehicle dynamics modeling, comparative evaluations for research and development purposes, and manufacturing quality control. This document is intended to be a general guideline for testing on an ideal machine. Users of this RP may modify the recommended protocols to satisfy the needs of specific use-cases; e.g., reducing the recommended number of test loads and/or pressures for benchmarking purposes. However, due care is necessary when modifying the protocols to maintain data integrity.
This specification covers an aluminum alloy in the form of die forgings and forging stock.
This specification covers an aluminum alloy in the form of die forgings and forging stock.
This specification covers the requirements for a manganese phosphate coating on ferrous alloys.
This specification covers one type of crystallized glass ceramic in the form of cast and pressed shapes.
This specification covers an aluminum alloy in the form of welding wire.
This specification covers a copper-zinc alloy (brass) in the form of laminated sheet.
This specification covers one type of aluminum bronze in the form of bars, rods, forgings, and forging stock.
This specification covers the design requirements and test procedures for separable beam seal fittings which includes end fittings (see 2.3.4), fitting bodies (see 2.3.7), and boss fittings (see 2.3.2) for use in aerospace fluid systems. Design requirements are for class 3000 in corrosion resistant steel (15-5 PH, 17-4 PH CRES) only and for class 4000 in titanium alloy (Ti) and corrosion and heat-resistant steel (nickel alloy 718 CRES) only. Definition of fittings and related terms are defined in 2.3.
This specification covers connector accessories for use with electrical connectors; see 6.8.
This specification covers an aluminum alloy in the form of honeycomb core in a non-hexagonal, flexible cell configuration, the core being treated for increased corrosion resistance and furnished only in the expanded form.
This specification covers a corrosion and heat-resistant nickel alloy in the form of investment castings.
This specification covers an iron-nickel alloy in the form of strip.
SAE J1333 applies to hydraulic cylinders which are components of self-propelled work machines defined in SAE J1116.
This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
This specification covers a corrosion and heat resistant aluminum coating material supplied as a liquid of suitable consistency for coating parts after being thoroughly mixed.
Items per page:
50
1 – 50 of 214212