Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers a titanium alloy in the form of sheet 0.020 to 0.1874 inch (0.51 to 4.760 mm), inclusive, in nominal thickness (see 8.6).
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing up to and including 1.000 inch (25.4 mm) in diameter, least thickness, or tube wall thickness (see 8.6).
This SAE Standard applies to machines as defined in Appendix A. Some of these machines can travel on-highway but function primarily off-highway.
This document presents design and application information which will allow optimized utilization of filter line wire and cable purchased to AS85485. Filter line wire is defined and design information is presented. The electrical and mechanical performance characteristics of the wire, along with recommended harnessing methods and techniques, are also presented.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of investment castings.
This specification covers an aluminum alloy in the form of bars and rods 0.500 to 8.000 inches (12.7 to 203.2 mm) in nominal diameter or least difference between parallel sides and up to 50 square inches (322.6 cm2) in cross-sectional area (see 8.6).
This specification covers a corrosion- and heat-resistant steel in the form of investment castings.
This specification covers an aluminum alloy in the form of sand castings (see 8.6).
This specification covers a titanium alloy in the form of sheet 0.025 through 0.100 inch (0.63 through 2.54 mm), inclusive, in thickness (see 8.6).
This specification covers an aluminum alloy in the form of castings (see 8.6).
This specification covers an aluminum alloy in the form of castings.
This specification covers a titanium alloy in the form of welding wire (see 8.5).
It is recommended that all helicopter engine development programs include an evaluation of engine starting requirements. The evaluation should include starting requirement effects on helicopter weight, cost, and mission effectiveness. The evaluation should be appropriate to the engine stage of development.
This specification covers a corrosion- and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash-welded rings, and stock for forging, flash-welded rings, or heading.
This specification covers the requirements for an electroless nickel-thallium-boron or nickel-boron deposit on various substrates.
SAE J1978-1 specifies a complementary set of functions to be provided by an OBD-II scan tool. These functions provide complete, efficient, and safe access to all regulated OBD (on-board diagnostic) services on any vehicle which complies to SAE J1979. The content of this document is intended to satisfy the requirements of an OBD-II scan tool as required by current U.S. OBD regulations. This document specifies: A means of establishing communications between an OBD-equipped vehicle and an OBD-II scan tool. A set of diagnostic services to be provided by an OBD-II scan tool in order to exercise the services defined in SAE J1979. In addition, SAE J1978-1 covers first generation protocol functionality defined in SAE J1979 plus automatic protocol determination for all SAE J1979/J1979-2/J1979-3 application content. The presentation of the SAE J1978 document family, where SAE J1978-1 covers first generation protocol functionality defined in SAE J1979 and protocol determination for SAE J1979, SAE
This specification covers flash-welded rings made of titanium and titanium alloys (see 8.5).
This SAE Recommended Practice was developed primarily for passenger car and truck applications but may be used in marine, industrial, and similar applications. It addresses nonmetallic caps and both metallic and nonmetallic filler necks.
This specification covers an aluminum-lithium alloy in the form of extruded profiles with a maximum cross-sectional area of 19 square inches (123 cm2) and a maximum circle size of 11 inches (279 mm) from 0.040 to 0.499 inch (1.00 to 12.50 mm) in thickness (see 8.6).
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This document applies to the development of Plans for integrating and managing COTS assemblies in electronic equipment and Systems for the commercial, military, and space markets, as well as other ADHP markets that wish to use this document. For purposes of this document, COTS assemblies are viewed as electronic assemblies such as printed wiring assemblies, disk drives, servers, printers, laptop computers, etc. There are many ways to categorize COTS assemblies1, including the following spectrum: At one end of the spectrum are COTS assemblies whose design, internal parts2, materials, configuration control, traceability, reliability, and qualification methods are at least partially controlled, or influenced, by ADHP customers (either individually or collectively) or by industry standards. An example at this end of the spectrum is a VME circuit card assembly. At the other end of the spectrum are COTS assemblies whose design, internal parts, materials, configuration control, and
This specification covers a copper-beryllium alloy in the form of bars, rods, shapes, and forgings (see 8.5).
This specification covers an aluminum alloy in the form of hand forgings 8 inches (203 mm) and under in nominal thickness and of forging stock (see 8.6).
This specification covers an aluminum alloy in the form of sheet and plate with a thickness of 0.125 to 0.499 inch (3.20 to 12.67 mm), inclusive (see 8.5).
This specification covers a corrosion-resistant steel product 12 inches (305 mm) and under in nominal diameter, thickness or, for hexagons, least distance between parallel sides, and having a maximum cross-sectional area of 144 in2 (930 cm2) in the solution and precipitation heat treated (H900A) condition.
This specification covers a corrosion- and heat-resistant steel in the form of welding wire.
This SAE Aerospace Standard (AS) describes the requirements for high temperature insulated crimp style terminal lugs and splices.
Items per page:
50
1 – 50 of 216126