Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers a nitriding grade of premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. AMS6496 and AMS6497 cover UNS K23280 with other quality levels.
This specification covers a magnesium alloy in the form of investment castings (see 8.6).
This specification covers an aluminum alloy in the form of rolled or forged rings up to 6 inches (152 mm), inclusive, in thickness (see 3.3.1.1.1) and an OD to wall thickness ratio of 10 or greater (see 8.5).
This procedure describes a method of measuring the resistance to wet color transfer of materials such as textiles, leather, and composites.
This SAE Aerospace Recommended Practice (ARP) provides the user with standardized guidelines for the measurement of effective intensity of short pulse width strobe anticollision lights for aircraft in the laboratory, in maintenance facilities, and in the field. A common source of traceability for calibration of the measurement systems, compensation for known causes of variation in light output such as the use of colored lenses, and recommendations which minimize sources of errors and uncertainties are included in this document. Estimates of uncertainty and error sources for each class of measurement are discussed.
This specification covers a magnesium alloy in the form of investment castings (see 8.6).
This specification covers a copper-zinc alloy (brass) in the form of sheet, strip, and plate (see 8.6).
This SAE Recommend Practice establishes for passenger cars, light trucks, and multipurpose vehicles with GVW of 4500 kg (10000 pounds) or less, as defined by the EPA, and M1 category vehicles, as defined by the European Commission:
This specification covers a low-alloy steel in the form of sheet, strip, and plate 4.00 inches (101.6 mm) and under in thickness.
This specification covers an aluminum alloy in the form of sheet from 0.063 to 0.249 inch (1.60 to 6.30 mm) in nominal thickness (see 8.6).
The purpose of this SAE Recommended Practice is to establish a uniform laboratory procedure for securing and reporting the friction and wear characteristics of brake linings. The performance data obtained can be used for in-plant quality control by brake lining manufacturers and for the quality assessment of incoming shipments by the purchasers of brake linings.
This specification covers a polytetrafluoroethylene (PTFE) resin filled with 15% aromatic polymer in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
This specification covers one type of epoxy-resin-impregnated carbon fibers in the form of tape and sheet.
This specification covers one type of epoxy-resin-impregnated carbon fibers in the form of tape and sheet.
This specification covers one type of organic fiber in the form of roving. The product shall be formed as three ends of 2450 denier yarn (AMS3901/13) collected into an approximately parallel arrangement without twist.
This specification covers a chemically or mechanically expanded polyether urethane (EU) elastomeric foam material in the form of ready-to-use sheet.
This specification establishes the requirements for a general-purpose brush plating of nickel applied by electrodeposition.
This specification covers a fluorocarbon (FKM) rubber stock in the form of molded test slabs.
This specification covers virgin, unfilled polytetrafluoroethylene (PTFE) in the form of sheet, manufactured by compression molding and sintering.
This specification covers one type of continuous multifilament carbon fibers in the form of a tow or yarn (when twisted). The weight per unit length of the tow or yarn is governed by the filament count which is identified by the supplier's grade or material designation.
This specification covers one type of polyether-type urethane (EU) resin and hardener which, when mixed and cured, produce elastomeric polyurethane products.
This specification covers an unfilled polyimide plastic in the form of molded rod and bar.
This specification covers one type of epoxy-resin-impregnated, non-woven, glass fiber in the form of tape for hand or machine layup and of flat sheet.
This specification covers a standard fluorosilicone (FVMQ) rubber stock in the form of molded test slabs.
This specification covers one type of organic fiber in the form of yarn. The product shall be formed as a multiplicity of filaments drawn together and gathered into an approximately parallel arrangement.
This specification covers a polytetrafluoroethylene (PTFE) resin filled with 40% bronze powder in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
This specification covers parallel-yarn ropes formed from impregnated aramid fibers.
This specification covers the specific requirements for aluminum alloy 5456 bar, rod, shapes, tube, and wire produced by extrusion.
This specification covers one type of paper coated on both sides with polyethylene film in the form of rolls of sheeting or reels of unperforated tape of the width specified.
This specification covers steel in the form of laminated sheet.
This specification covers one weight and strength of para-aramid thread.
This specification covers one width and strength of nylon tape.
This specification covers one type of nylon in the form of webbing.
This specification covers a polyalphaolefin/ester-blend fluid.
This specification covers one type of paper in the form of perforated tape of the width specified herein.
This specification covers a kraft paper, coated on both sides and with different release characteristics on each side (i.e., differentially coated), supplied in the form of rolls of sheeting or reels of unperforated tape of the width specified.
This specification covers a polytetrafluoroethylene (PTFE) resin filled with carbon fiber in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
Items per page:
50
1 – 50 of 216070