Results
This SAE Standard covers low voltage battery cable intended for use at a nominal system voltage of 60 VDC (25 VAC) or less in surface vehicle electrical systems. The tests are intended to qualify cables for normal applications with limited exposure to fluids and physical abuse.
This SAE Aerospace Recommended Practice (ARP) contains methods used to measure the optical performance of airborne electronic flat panel display (FPD) systems. The methods described are specific to the direct view, liquid crystal matrix (x-y addressable) display technology used on aircraft flight decks. The focus of this document is on active matrix, liquid crystal displays (LCD). The majority of the procedures can be applied to other display technologies, however, it is cautioned that some techniques need to be tailored to different display technologies. The document covers monochrome and color LCD operation in the transmissive mode within the visual spectrum (the wavelength range of 380 to 780 nm). These procedures are adaptable to reflective and transflective displays paying special attention to the source illumination geometry. Photometric and colorimetric measurement procedures for airborne direct view CRT (cathode ray tube) displays are found in ARP1782. Optical measurement
This SAE Recommended Practice establishes the procedure for determining if recreational motorboats have effective exhaust muffling means when operating in the stationary mode. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.
This specification covers a dilute aluminum/TiB2 metal matrix composite in the form of sand castings.
This SAE Aerospace Standard (AS) defines a series of standardized tube walls to be used for high pressure hydraulic tubing. These tube walls are applicable to all homogenous tube materials (i.e., aluminum, steel, titanium) throughout a rated pressure range of 1000 to 8000 psi and a maximum rated operating temperature range of 160 to 450 °F. All future aerospace applications for which a required tube outside diameter/tube wall combination is not presently available shall be selected from the table contained herein (see Figure 1).
This specification covers an aluminum alloy in the form of castings.
This specification covers a titanium alloy in the form of bars, wire, forgings up to 4.000 inches (101.60 mm), inclusive, and forging stock.
This SAE Aerospace Recommended Practice (ARP) discusses the desired characteristics of night vision goggle (NVG) filters that can be used with incandescent, electroluminescent (EL) and light emitting diode (LED) light sources to achieve NVG compatible lighting of aerospace crew stations. This document also discusses the parameters that need to be considered when selecting a night vision goggle/daylight viewing (NVG/DV) filter for proper contrast enhancement to achieve readability in daylight. The recommendations set forth in this document are to aid in the design of NVG compatible lighting that will meet the requirements of MIL-L-85762A and MIL-STD-3009.
This Standard covers the requirements for all marine inboard and outboard gasoline engine ignition assemblies and components.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This SAE Aerospace Standard (AS) covers components of rotary flap assemblies to be used with portable equipment for peening of metal parts. The flap assemblies consist of a flap attached to a mandrel and shall be of the following sizes:
This SAE Standard covers the dimensional and general specifications, including performance requirements, for carbon steel self-drilling tapping screws suitable for use in general applications having point Styles 2, 3, 4, and 5. It is the objective of this document to ensure that carbon steel self-drilling tapping screws, by meeting the mechanical and performance requirements specified, shall drill a hole and form or cut mating threads in materials into which they are driven without deforming their own thread and without breaking during assembly.
This SAE Recommended Practice is intended as a guide toward standard practice but may be subject to frequent change to keep pace with experience and technical advances.
Common or obvious surface imperfections are normally visible to the naked eye before or after fabrication or processing. Illustrations and definitions of these imperfections are contained in this SAE Information Report. The identifying names are those commonly used throughout the steel industry. The imperfections identified include the major and most often encountered imperfections known to exist at this time. These imperfections are variable in appearance and severity. Extreme conditions have been selected in some instances in order to obtain suitable photographs. Photographs are courtesy of the American Iron and Steel Institute, Kaiser Aluminum, U.S. Steel, Nucor Steel, Samuel Steel, Steel Dynamics, Worthington Steel, and companies no longer in existence: LTV Steel, National Steel, and The Budd Company.
This report is intended to provide users and producers of metallic shot and grit1 with general information on methods of mechanically testing metal abrasives in the laboratory.
This document applies to the requirements of a device used in the field and inspection stations to aim and check aim of mechanically aimable headlamp units. The purpose of this document is to provide a laboratory test procedure to determine whether the devices under test are capable of accurately positioning headlamp units from their aiming pads and maintaining their accuracy in service within the tolerances designated in this document.
This SAE Recommended Practice establishes for passenger cars, light trucks, and multipurpose vehicles with GVW of 4500 kg (10 000 lb) or less: a Minimum performance standards for the windshield washer system. b Test procedures that can be conducted on uniform test equipment by commercially available laboratory facilities. c Uniform terminology of windshield washer system characteristics and phenomena consistent with those found in guides for the use of engineering layout studies to evaluate system performance. d Guides for the design and location of components of the systems for function, servicing of the system, etc. The minimum performance requirements and test procedures, outlined in this document, are based on currently available engineering data. It is intended that all portions of the document will be periodically reviewed and revised as additional data on windshield washer system performance are developed.
This SAE Recommended Practice establishes the location of drivers’ eyes inside a vehicle. Elliptical (eyellipse) models in three dimensions are used to represent tangent cutoff percentiles of driver eye locations. Procedures are provided to construct 95th and 99th percentile tangent cutoff eyellipses for a 50/50 gender mix, adult user population. Neck pivot (P) points are defined in Section 6 to establish specific left and right eye points for direct and indirect viewing tasks described in SAE J1050. These P points are defined only for the adjustable seat eyellipses defined in Section 4. This document applies to Class A Vehicles (Passenger Cars, Multipurpose Passenger Vehicles, and Light Trucks) as defined in SAE J1100. It also applies to Class B vehicles (Heavy Trucks), although these eyellipses have not been updated from previous versions of SAE J941. The appendices are provided for information only and are not a requirement of this document.
This SAE Recommended Practice applies to highway trailer tow bar eye-type applications, including multiple trailers.
This SAE Recommended Practice establishes a uniform procedure for the level road test of the brake systems of new light-duty trucks and new multipurpose passenger vehicles1 up to and including 2700 kg (6000 lb) GVW and all classes of new passenger cars.
This SAE Recommended Practice applies to fifth wheel kingpins for heavy-duty commercial trailers and semitrailers, used for off-highway operation or in hauling heavy loads (see Figure 1).
This SAE Recommended Practice applies to speedometers, odometers, and speedometer drives typical of passenger vehicles, buses, and trucks used for personal or commercial purposes. The method of determining wheel revolutions per unit distance (3.1) and overall system design variation (3.3.3) are applicable to passenger cars only. Comparable recommendations for trucks and buses are under development. The data of tachometers is applicable to vehicular use, as previously described, and also to stationary and marine engines and special vehicles.
This SAE Standard applies to all machines with shovel, clam, or dragline attachment.
ARP4761A and its EUROCAE counterpart, ED-135, present guidelines for performing safety assessments of civil aircraft, systems, and equipment. They may be used when addressing compliance with certification requirements (e.g., 14 CFR/CS Parts 23, 25, 27, and 29 and 14 CFR Parts 33, 35, CS-E, and CS-P). ARP4761A/ED-135 may also be used to assist a company in meeting its own internal safety assessment standards. While the safety assessment processes described are primarily associated with civil aircraft, systems, and equipment, these processes may be used in many other applications. The guidelines herein identify a systematic safety assessment process, but other processes may be equally effective. The processes described herein are usually applicable to the new designs or to existing designs that are affected by changes to design or functions. In the case of the implementation of existing design(s) in a derivative application, complementary means such as service experience in a similar
The task of chemical process operator in the parts cleaning area is generally considered unskilled labor and in the past, little or no training had been provided or recommended. Since overhaul cleaning is a critical process step prior to visual and fluorescent penetrant inspection processes, consideration must be given to minimum levels of training for these process operators. It is the responsibility of the department supervisor to ensure that all personnel within the department are trained to acceptable level in all general aspects of health and safety and basic operating procedures. This document is intended to augment the local quality control system which will control the application and frequency of the guidelines stated within.
The material defined by this SAE document is an impact modified, heat stabilized, 66 nylon reinforced with glass fibers. This material is for use in dust shields for hydraulic disc brakes. NOTE—The applicability of a plastic dust shield must be evaluated for each individual brake system. Its use with solid rotors and/or high performance brake systems is not recommended.
Items per page:
50
1 – 50 of 212735