Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This procedure describes a method of measuring the resistance to wet color transfer of materials such as textiles, leather, and composites.
This SAE Recommend Practice establishes for passenger cars, light trucks, and multipurpose vehicles with GVW of 4500 kg (10000 pounds) or less, as defined by the EPA, and M1 category vehicles, as defined by the European Commission:
This SAE Aerospace Recommended Practice (ARP) provides the user with standardized guidelines for the measurement of effective intensity of short pulse width strobe anticollision lights for aircraft in the laboratory, in maintenance facilities, and in the field. A common source of traceability for calibration of the measurement systems, compensation for known causes of variation in light output such as the use of colored lenses, and recommendations which minimize sources of errors and uncertainties are included in this document. Estimates of uncertainty and error sources for each class of measurement are discussed.
This specification covers a magnesium alloy in the form of investment castings (see 8.6).
This specification covers an aluminum alloy in the form of sheet from 0.063 to 0.249 inch (1.60 to 6.30 mm) in nominal thickness (see 8.6).
This specification covers a low-alloy steel in the form of sheet, strip, and plate 4.00 inches (101.6 mm) and under in thickness.
This specification covers a copper-zinc alloy (brass) in the form of sheet, strip, and plate (see 8.6).
The purpose of this SAE Recommended Practice is to establish a uniform laboratory procedure for securing and reporting the friction and wear characteristics of brake linings. The performance data obtained can be used for in-plant quality control by brake lining manufacturers and for the quality assessment of incoming shipments by the purchasers of brake linings.
This specification covers a carbon steel in the form of bars up through 3.000 inches (76.20 mm) and forgings and forging stock of any size.
This specification covers engineering requirements for applying tungsten carbide thermal spray coatings to ultrahigh-strength steels (220 ksi and above) utilizing high-velocity oxygen fuel (HVOF) combustion-driven processes and the properties for such coatings. The processes and procedures herein apply only to the properties of the as-deposited coating.
This specification covers an aluminum alloy in the form of sheet and plate 0.010 to 1.750 inch (0.25 to 44.45 mm) in thickness, supplied in the annealed (O temper) condition. When specified, product shall be supplied in the “as fabricated” (F) temper (see 8.5).
This specification covers an aluminum alloy in the form of castings with nominal wall thickness up to 1.0 inch (25 mm) (see 8.8).
This specification covers a titanium alloy in the form of bars, wire, forgings up to 4.000 inches (101.60 mm), inclusive, and forging stock.
This specification covers an aluminum alloy in the form of centrifugal castings (see 8.6).
This specification covers a titanium alloy in the form of sheet, strip, and plate up through 4.000 inches (101.60 mm), inclusive, in thickness (see 8.6).
This specification covers a premium aircraft-quality, corrosion-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash-welded rings up to 8.0 inches (203 mm) in diameter or least distance between parallel sides in the solution heat-treated condition (see 8.4), and stock of any size for forging, flash-welded rings, or heading.
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a corrosion- and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash-welded rings, and stock for forging or flash-welded rings.
This specification covers a corrosion-resistant steel product 12 inches (305 mm) and under in nominal diameter, thickness, or for hexagons, least distance between parallel sides in the solution and precipitation heat treated (H950) condition.
This specification covers a premium aircraft-quality alloy steel in the form of welding wire.
This specification covers a titanium alloy in the form of forgings 3.000 inches (76.20 mm) and under in nominal diameter or least distance between parallel sides and 9 square inches (58 cm2) and under in cross-sectional area, and forging stock of any size (see 8.6).
This specification covers a corrosion- and heat-resistant nickel alloy in the form of investment castings.
This specification covers an iron-nickel alloy in the form of strip 0.020 to 0.250 inch (0.51 to 6.35 mm), inclusive, in thickness.
This specification covers one type of a non-melting, heat-stable silicone compound, for use in high tension electrical connections, ignition systems, and electronics equipment, for application to unpainted mating threaded or non-threaded surfaces, and as a lubricant for components fabricated from elastomers. This compound is effective in the temperature range from -54 °C (-65 °F) to +204 °C (400 °F) for extended periods. This compound is identified by NATO symbol S-736 (see 6.5).
This SAE Aerospace Recommended Practice (ARP) describes training and approval of personnel performing certain thermal processing and associated operations that could have a material impact on the properties of materials being processed. It also recommends that only approved personnel perform or monitor the functions listed in Table 1.
This specification covers a titanium alloy in the form of forgings, 6.000 inches (152.40 mm) and under in cross-sectional thickness and forging stock of any size.
The intent of this specification is for the procurement of the material listed on the QPL; therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program must refer to the Quality Assurance section of the base specification, AMS6891.
This specification covers a dilute aluminum/TiB2 metal matrix composite in the form of investment castings.
This specification covers a corrosion and heat resistant steel in the form of sand castings.
This specification covers a low-alloy steel in the form of investment castings.
This specification covers the requirements of uncoated aluminum alloy foil for core materials required for structural sandwich construction.
This specification covers an alloy steel in the form of investment castings.
This specification covers a shampoo type carpet cleaner in the form of a liquid.
Items per page:
50
1 – 50 of 216063