Results
This method is intended to evaluate the thermal and oxidative stability of synthetic, ester-based aviation lubricants under defined conditions of time and temperature. This method is applicable to lubricants meeting the compositional and performance requirements of AS5780.
Long wave ultraviolet or UV-A irradiation (between 320 and 400 nm) is used for fluorescent inspections in magnetic particle and liquid penetrant examinations. UV-A irradiation is obtained from either LED, fluorescent, or high intensity discharge lamps that are stationary or portable. Commercially available UV-A lamps possess a large variation in intensity output that may introduce a legitimate concern for possible health hazards. This document reviews the nature of UV-A irradiation emitted by lamps and acceptable UV dosage limits adopted by the American Conference of Governmental Industrial Hygienists (ACGIH®) and European Union and recommendation of proper practices when working with UV-A irradiation.
This specification covers the installation of aircraft interior lighting for military aircraft.
This document provides recommendations to identify battery group sizes and dimensions for 6 V, 8 V, 12 V, and 24 V lead acid batteries.
This specification covers a manganese alloy in the form of powder, preforms, and a viscous mixture (paste) of the powder in a suitable binder.
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate.
This specification establishes the procedures used to produce a hard anodic coating on magnesium alloys and the properties of the coating.
This document outlines general requirements for the use of CFD methods for aerodynamic simulation of medium and heavy commercial ground vehicles weighing more than 10000 pounds. The document provides guidance for aerodynamic simulation with CFD methods to support current vehicle characterization, vehicle development, vehicle concept development, and vehicle component development. The guidelines presented in the document are related to Navier-Stokes and Lattice-Boltzmann based solvers. This document is only valid for the classes of CFD methods and applications mentioned. Other classes of methods and applications may or may not be appropriate to simulate the aerodynamics of medium and heavy commercial ground vehicle weighing more than 10000 pounds.
This SAE Standard applies to 12-volt lead-acid storage batteries that are designed specifically for start-stop operations in on-road passenger vehicles or light trucks. Included are definitions of terms, general testing recommendations, key performance characteristics, and life testing. Properties not unique to start-stop batteries should be tested according to SAE J537 or other applicable testing protocols.
The intent of this specification is for the procurement of carbon fiber and fiberglass epoxy prepreg products with 350 °F (177 °C) cure for aerospace applications; therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program must refer to the production quality assurance section (see 4.3) of this base specification, AMS6891.
This specification covers a titanium alloy in the form of extruded bars, tubes, and shapes, flash-welded rings up through 4.000 square inches (25.81 cm2) cross section, and stock for flash-welded rings (see 8.6).
This Purchasing Specification (PS) AMS3970/4 specifies the batch release and delivery requirements for film adhesive used for repair. This specification is applicable only when the film adhesive is used as part of the prepreg system as defined in AMS3970 and AMS3970/1. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials which are qualified and shall be carried out within the responsibility of the purchaser and under control of its Quality organization.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
AMS3970/2B gives specific information about the qualification program for carbon fiber fabric reinforced epoxy structural repair prepreg systems, curing under vacuum at 120 °C (250 °F), and a companion non-structural glass fabric prepreg used for repair of carbon fiber reinforced epoxy structures. The prepreg system shall include an epoxy film adhesive to be applied in a co-curing process with the prepreg for joint solid laminate and sandwich bonding.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, flash-welded rings under 4 inches (102 mm) in least cross-sectional dimension, and stock of any size for forging or flash-welded rings (see 8.3).
This Purchase Specification (PS), AMS3970/5, specifies the batch release and delivery requirements for the companion non-structural glass fiber fabric prepreg. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials which are qualified and shall be carried out within the responsibility of the purchaser and under control of its Quality organization.
This specification covers non-silicone synthetic rubber sealing compounds supplied as a two-component or pre-mixed and frozen (PMF) system that cures at room temperature.
This Purchasing Specification (PS), AMS3970/3, specifies the batch release and delivery requirements for carbon fiber fabric epoxy prepreg used for repair. This specification is applicable only when the carbon fiber fabric epoxy prepreg is used as part of the repair system defined in AMS3970 and AMS3970/1. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials that are qualified against AMS3970 (refer to PRI QPL AMS3970) and shall be carried out within the responsibility of the purchaser and under control of its Quality organization.
The intent of this specification is for the procurement of the material listed on the QPL; therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program must refer to the Quality Assurance section of the base specification, AMS6891.
The purpose of this document is to establish guidelines for determining the critical R134a and R1234yf refrigerant charge for off-road, self-propelled work machines as defined in SAE J1116 and agricultural tractors as defined in ANSI/ASAE S390. It will develop a minimum to maximum refrigerant charge range in which the HVAC system can maintain proper operation. Operating conditions and characteristics of the equipment will influence the optimum charge. Since these conditions and characteristics vary greatly from one application to another, careful consideration should be taken to determine the optimum R134a and R1234yf refrigerant charge for the HVAC system.
This SAE Aerospace Standard (AS) defines the requirements for polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assemblies suitable for use in aerospace hydraulic, fuel, and lubricating oil systems at temperatures between -67 and 450 °F for Class I assemblies, -67 and 275 °F for Class II assemblies, and at nominal pressures up to 1500 psi. The hose assemblies are also suitable for use within the same temperature and pressure limitations in aerospace pneumatic systems where some gaseous diffusion through the wall of the PTFE liner can be tolerated. The use of these hose assemblies in pneumatic storage systems is not recommended. In addition, installations in which the limits specified herein are exceeded, or in which the application is not covered specifically by this standard (for example, oxygen), shall be subject to the approval of the procuring activity.
This SAE Standard provides general and dimensional specifications for beaded ends and hose fittings. These connections are intended for general applications in low-pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown are designed to be used with hoses that are intended to be retained by hose clamps. It is recommended that where step sizes or additional types of fittings are required they be designed to conform with the specifications of this document insofar as they may apply. The following general specifications shall supplement the dimensional data contained in the tables with respect to all unspecified detail.
This specification covers a low-carbon steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a low-alloy steel in the form of welding wire.
This specification covers types and classes of polysulfide sealing compound supplied as a two-component system suitable for application by brush, or by extrusion gun, spatula brush, or roller.
This specification covers a low-alloy steel in the form of welding wire.
This specification covers steel forgings suitable for use in the construction of aircraft/aerospace equipment, special ordnance, and related accessories.
This specification covers a maraging steel in the form of welding wire.
This SAE Standard applies to Carbon Dioxide R-744 refrigerant used to service motor vehicle passenger air-conditioning (A/C) systems designed to use CO2 (R-744). Hermetically sealed, refrigerated cargo systems are not covered by this document.
This SAE Standard applies to new refrigerant used in motor vehicle passenger air-conditioning (A/C) systems designed to use HFC-134a. Hermetically sealed, refrigerated cargo systems are not covered by this document.
The purpose of this SAE Information Report is to provide information on refrigerant issues of concern to the mobile air-conditioning industry.
This SAE standard provides manufacturers/marketers, testing facilities, and providers of technician training with a procedure for certifying compliance with the applicable standard. Manufacturers/marketers or sellers who advertise their products as certified to an SAE J standard shall follow this procedure. Certification of a product is voluntary; however, this certification process is mandatory for those advertising meeting SAE standard(s) requirements. Only certifying to this standard allows those claiming compliance to advertise that their product (unit), component, or service technician training meets all requirements of the applicable SAE standard. Certification of compliance to this and the appropriate standard and use of the SAE label on the product shall only be permitted after all the required information has been submitted to SAE International and it has been posted on the SAE website. This process is mandatory for those advertising as being “Certified to SAE JXXXX-(version
The scope of SAE J2064 covers coupled hose assemblies intended for containing and circulating lubricant, liquid, and gaseous R-134a, R-152a, and/or R-1234yf refrigerant in automotive air-conditioning systems. Historically, requirements for the hose used in coupled automotive refrigerant air conditioning assemblies was included in SAE J2064. SAE J2064 has been changed to establish the requirements for factory and field coupled hose assemblies. SAE J3062 has been issued to define requirements for the hose used in these assemblies into its own standard. SAE J2064 also provides the necessary values used in SAE J2727. The certified coupling of MAC hose assemblies is required in meeting certain regulatory requirements. A hose which has met the requirements of SAE J3062 and certified in SAE J2911 shall be used as part of the coupled assembly. A hose which meets the requirements of SAE J3062 does not ensure the assembly will meet the requirements of SAE J2064. It is the hose assembly
Items per page:
50
1 – 50 of 221931