This content is not included in your SAE MOBILUS subscription, or you are not logged in.
- Ground Vehicle Standard
Published December 15, 2016 by SAE International in United States
Downloadable datasets availableAnnotation ability available
This SAE Standard provides general, dimensional and performance specifications for the most common hoses used in hydraulic systems on mobile and stationary equipment.
The general specifications contained in Sections 1 through 12 are applicable to all hydraulic hoses and supplement the detailed specifications for the 100R-series hoses contained in the later sections of this document. (See Tables 1A and 1B).
This document shall be utilized as a procurement document only to the extent as agreed upon by the manufacturer and user.
The maximum working pressure of a hose assembly comprising SAE J517 hose and hose connectors per SAE J516, SAE J518, SAE J1453, etc., shall not exceed the lower of the respective SAE maximum working pressure values.
When using SAE J517 hose for marine applications, see SAE J1475, SAE J1942 and SAE J1942-1.
The SAE J517 100R9, 100R10 and 100R11 hoses are discontinued due to lack of demand. For DOD orders see Appendix C.
The SAE J517 100R1A, 100R2A, 100R2B and 100R 2BT are discontinued due to lack of demand. For DOD orders replace 100R1A with 100R1AT, replace 100R2A, 100R2B and 100R2BT with 100R2AT.
The SAE J517 100R1AT maximum working pressures were replaced by the type S maximum working pressures beginning with the year 2009, eliminating the need to label 100R1 as type S.
The SAE J517 100R2AT maximum working pressures were replaced by the type S maximum working pressures beginning with the year 2009, eliminating the need to label 100R2 as type S.
The SAE J517 100R16 maximum working pressures were replaced by the type S maximum working pressures beginning with the year 2009, eliminating the need to label 100R16 as type S.
General revision of SAE J517 to add a workmanship clause to Wire Inserted Hydraulic Suction Hose (SAE 100R4)
Paragraph 19.5 workmanship clause to ensure that the internal wire is clipped sufficiently back far enough for handling of the hose.
Paragraph 7 was added to describe how the overall length of a hose is measured along with the cut on the end.
Figure 1 was added to graphically show the dimension of the hose end cut.
Figure 5 was added to graphically show the spiral wire inside the hose and minimum dimension back it shall be cut.
|Ground Vehicle Standard||Hydraulic Hose|
|Ground Vehicle Standard||Hose Assemblies, Rubber, Hydraulic, Steel Wire Reinforced -Part 2: Ordering Information|
Data Sets - Support Documents
|Unnamed Dataset 1|
|Unnamed Dataset 2|
|Unnamed Dataset 3|
|Unnamed Dataset 4|
|Unnamed Dataset 5|
|Unnamed Dataset 6|
|Table 1||Summary of SAE J517 100R-series hose maximum working pressures (MPa) metric-Size (SAE dash size)|
|Table 2||Summary of SAE J517 100R-series hose maximum working pressure (MPa) metric-size (SAE dash size)|
|Unnamed Dataset 9|
|Unnamed Dataset 10|
|Table 3||Tolerances on assembly length|
|Table 4||SAE J517 Qualification test requirements|
|Table 5||Dimensions and specifications for SAE 100R1 hose|
|Table 6||Hose concentricity (100R1)|
|Table 7||Dimensions and specifications for SAE 100R2 hose|
|Table 8||Hose concentricity (100R2)|
|Table 9||Dimensions and specifications for SAE 100R3 hose|
|Table 10||Hose concentricity (100R3)|
|Table 11||Dimensions and specifications for SAE 100R4 hose|
|Table 12||Dimensions and specifications for SAE 100R5 hose|
|Table 13||Hose concentricity (100R5)|
|Table 14||Dimensions and specifications for SAE 100R6 hose|
|Table 15||Hose concentricity (100R6)|
|Table 16||Dimensions and specifications for SAE 100R7 hose|
|Table 17||Hose concentricity (100R7)|
|Table 18||Dimensions and specifications for SAE 100R8 hose|
|Table 19||Hose concentricity (100R8)|
|Table 20||Dimensions and specifications for SAE 100R12 hose|
|Table 21||Hose concentricity (100R12)|
|Table 22||Dimensions and specifications for SAE 100R13 hose|
|Table 23||Hose concentricity (100R13)|
|Table 24||Dimensions and specifications for SAE 100R14 hose|
|Table 25||Hose tube dimensions and concentricity (100R14)|
|Table 26||Dimensions and specifications for SAE 100R15 hose|
|Table 27||Hose concentricity (100R15)|
|Table 28||Dimensions and specifications for SAE 100R16 hose|
|Table 29||Hose concentricity (100R16)|
|Table 30||Dimensions and specifications for SAE 100R17 hose|
|Table 31||Hose concentricity (100R17)|
|Table 32||Dimensions and specifications for SAE 100R18 hose|
|Table 33||Hose concentricity (100R18)|
|Table 34||Dimensions and specifications for SAE 100R19 hose|
|Table 35||Hose concentricity (100R19)|
|Table 36||MPa to psi conversion table|
|Table 37||Hose codes|
|Table 38||Replacement recommendations for 100R9, 100R10 and 100R11 spiral hoses|
Hydraulic Hose and Hose Fittings Committee
The Hydraulic Hose and Hose Fittings Subcommittee of the FCCTC develops and maintains SAE Standards, Recommended Practices and Information Reports relating to hydraulic hose and hose fittings with an intended use in pressure applications. Participants in the FCCTC Hydraulic Hose and Hose Fittings Subcommittee include OEMs, suppliers, consulting firms, government and other interested parties.
* Redlines comparisons are available for those standards listed in the Revision History that contain a radio button. A redline comparison of the current version against a revision is accomplished by selecting the radio button next to the standard and then selecting 'compare'. At this time, Redline versions only exist for some AMS standards. SAE will continue to add redline versioning with ongoing updates to SAE MOBILUS.