This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Fitting—O-Ring Face Seal
- Ground Vehicle Standard
- J1453_200901
- Cancelled
Downloadable datasets available
Annotation ability available
Sector:
Issuing Committee:
Language:
English
Scope
This SAE Standard covers material, dimensional, and performance requirements of steel O-ring face seal fittings for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube or hose diameters 6.35 mm (0.250 in) through 38.1 mm (1.500 in). These fittings are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These fittings are capable of providing leak-proof full flow connections in hydraulic systems operating from 95 kPa (28 in Hg) vacuum to working pressures shown in Table 1. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums. For any application, it is recommended that sufficient testing be conducted and reviewed by both the user and manufacturer to assure that required performance levels will be safe. See Figure 1.
The rated working pressure of a fluid conductor assembly using SAE J1453 hose stem connections or formed tube connection per Figure 32a, shall not exceed rated working pressure of the lowest rated component thereof.
Rationale
SAE J1453 is being cancelled because it has been replaced by SAE J1453-1, SAE J1453-2, and SAE J1453-3.
Recommended Content
Ground Vehicle Standard | Specification for O-Ring Materials Used with Hydraulic Connectors |
Aerospace Standard | PACKING, PREFORMED - O-RING SEAL AMS7259 |
Ground Vehicle Standard | Automotive Tube Fittings |
Topic
Data Sets - Support Documents
Title | Description | Download |
---|---|---|
TABLE 1 | WORKING PRESSURE RATINGS CAPABLE OF 4 TO 1 MINIMUM BURST | |
TABLE 2 | DRILL TOLERANCES | |
TABLE 3 | MAXIMUM TORQUE TO MOVE WASHER AND WASHER FLATNESS | |
TABLE 4 | WORKING, PROOF, AND MINIMUM BURST PRESSURES | |
TABLE 5 | QUALIFICATION TEST TORQUE REQUIREMENTS | |
TABLE 6 | FITTING DIMENSIONS ( TO ) | |
Unnamed Dataset 7 | ||
Unnamed Dataset 8 | ||
Unnamed Dataset 9 | ||
Unnamed Dataset 10 | ||
Unnamed Dataset 11 | ||
Unnamed Dataset 12 | ||
Unnamed Dataset 13 | ||
Unnamed Dataset 14 | ||
Unnamed Dataset 15 | ||
Unnamed Dataset 16 | FIGURES 32 TO 32A—STANDARD SLEEVE AND CAP ASSEMBLY | |
Unnamed Dataset 17 | ||
Unnamed Dataset 18 | ||
Unnamed Dataset 19 | ||
TABLE 10B | DIMENSIONS FOR STRAIGHT O-RING BOSS JUMP FITTINGS ( ) | |
TABLE A1 | DIMENSIONS FOR SURFACE ACCEPTANCE CRITERIA | |
TABLE D1 | METRIC FLAT SIZES |
Issuing Committee
Hydraulic Tube Fittings Committee
The Hydraulic Tube Fittings Subcommittee of the FCCTC develops and maintains SAE Standards, Recommended Practices and Information Reports relating to hydraulic and pneumatic tube fittings for all fluid power applications except hydraulic and pneumatic brake applications Participants in the FCCTC Hydraulic Tube Fittings Subcommittee include OEMs, suppliers, consulting firms, government and other interested parties.
Reference
Number | Title |
---|
* Redlines comparisons are available for those standards
listed in the Revision History that contain a radio button. A
redline comparison of the current version against a revision is
accomplished by selecting the radio button next to the standard and
then selecting 'compare'. At this time, Redline versions only exist
for some AMS standards. SAE will continue to add redline versioning
with ongoing updates to SAE MOBILUS.