This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
An Experimental Evaluation of the Oil Fouling Effects of Two-Stroke Oxidation Catalysts
Annotation ability available
Sector:
Language:
English
Abstract
Washcoat sintering and substrate meltdown have traditionally been the principle deactivating mechanisms of catalysts fitted to two-stroke engines. The reduction of the excessively high HC and CO levels responsible for these effects has therefore been the focus of considerable research which has led to the introduction of direct in-cylinder fuel injection to some larger versions of this engine. However, much less attention has been paid to the effects of oil and its additives on the performance and durability of the two-stroke catalyst. The quantity of oil emitted to the exhaust system of the majority of two-stroke engines is much greater than in four-stroke engines of comparable output due to the total loss lubrication system employed. The fundamental design of the two-stroke also permits some of this oil to ‘short-circuit’ to the exhaust in a neat or unburned form. The effect of this oil on the catalyst and the subsequent effect of the catalyst on the oil is the subject of this paper.
Two separate experimental test facilities were used during this investigation. The first was a computer-controlled catalyst test rig which uses a synthetic exhaust gas to examine the light-off characteristics of the catalyst in an accurate and repeatable manner. The second was based on a propane gas burner and was used to subject the catalyst to oil under conditions representative of those experienced on an operating engine.
Two oil types were formulated specifically for this study, one containing a minimal sulphur concentration and one containing 1.02% sulphur. It was found that oil with a low sulphur content caused only temporary deactivation which could be removed by simply heating the catalyst while oil which contained a high level of sulphur caused immediate and permanent deactivation. It was also found that the temperature at which the oil was layered onto the catalyst had a significant effect on the post-oiling light-off performance with CO conversion being inhibited to a greater degree than HC conversion. BET surface area measurements revealed a significant reduction in the number of micropores in the 5-10Å region while surface reaction rate considerations suggested a loss in metal surface area of over 50%.
Recommended Content
| Technical Paper | Catalyst Deactivation on a Two-Stroke Engine |
| Technical Paper | Minimizing Short-Circuiting Losses in 2-S Engines by Throttling the Exhaust Pipe |
Authors
Citation
McCullough, G., Douglas, R., McDowell, A., and Kenny, R., "An Experimental Evaluation of the Oil Fouling Effects of Two-Stroke Oxidation Catalysts," SAE Technical Paper 982014, 1998, https://doi.org/10.4271/982014.Also In
References
- Carberry, B. P. Magee, J. Douglas, R. “The Viability of Catalysing a Carburetted 50cc Two-Stroke Cycle Engine For Moped Applications.” SAE Paper No. 952136
- Thornhill, D.J. Fleck, R. “Design of a Blower-Scavenged, piston ported V6, Two-stroke Automotive Engine” SAE Paper No. 930980
- Williamson, W. Gandhi, H.S. Heyde, M.E. Zawacki, G.A. “Deactivation of Three-Way Catalysts by Fuel Contaminants: - Lead, Phosphorus and Sulphur” SAE Paper No. 790942
- Joy, G.C. Lester, G.R. Molinaro, F.S. “The Influence of Sulphur Species on the Laboratory Performance of Automotive Three Component Control Catalysts” SAE Paper No. 790943
- Hunter, J.E. “Studies of Catalyst Degradation in Automotive Emission Control Systems” SAE Paper No. 720122
- Furey, R.L. Monroe, D.R. “Fuel Sulphur Effects on the Performance of Automotive Three-Way Catalysts during Vehicle Emissions Tests” SAE Paper No. 811228
- McCullough, G. Douglas, R. “Reaction Mapping during light-off in a two-stroke oxidation catalyst” SAE Paper No. 961808
- Stenbom, B. Smedler, G. Nilsson, H.P. Lundgren, S. Wirmark, G. “Thermal Deactivation of a three-way Catalyst: Changes to Structural and Performance Properties” SAE Paper 900273
- Montreuil, C. N. 1992 Williams, S.C. Adamczyk, A. “Modeling Current Generation Catalytic Convertors: Laboratory Experiments and Kinetic Parameter Optimization - Steady State Kinetics” SAE 920096