This content is not included in your SAE MOBILUS subscription, or you are not logged in.
Simultaneous Application of Optical Spark Plug Probe and Head Gasket Ionization Probe to a Production Engine
ISSN: 0148-7191, e-ISSN: 2688-3627
Published March 01, 1993 by SAE International in United States
Annotation ability available
The optical spark plug probe and ionization head gasket probe developed at Sandia Laboratories were applied to one cylinder of a production multicylinder automotive gasoline engine. The purpose of this application is to eventually study combustion phenomena leading to high emissions under cold start and cold idle conditions. As a first step in studying cold start combustion and emissions issues, diagnostic instrumentation was simultaneously applied to a production engine under steady state idle, road load and an intermediate load-speed condition. The preliminary application of such instrumentation is the subject of the present paper.
The spark plug probe was redesigned for ease of use in production engines and to provide a more robust design. The two probes were geometrically oriented to obtain radial line-up between the optical windows and ionization probes. Data were taken simultaneously with both probes at the three load-speed conditions mentioned above. In addition, the production cylinder head was modified to obtain a substantially higher tumble swirl level and the same tests repeated. Correlations between flame arrival times at the optical windows and corresponding ionization probes were attempted. Literature indicates that the shape, growth rate and displacement of the early spark kernel may be responsible for cycle to cycle variation. Data presented in this paper do not show any correlation between flame arrival times at geometrically corresponding optical (spark plug) and ionization (head gasket) probes. On a cycle by cycle basis, the shape of the early flame kernel (or its displacement) does not bear any similarity to the shape towards the end of combustion.
Flame arrival times were also determined as a function of load-speed and tumble swirl level. Data show that flame kernel speed and flame arrival times at the head gasket are strongly affected by load-speed conditions. Flame velocities (and arrival times) appear to be unaffected by high tumble swirl under all load-speed conditions tested. No direct measurement of turbulence generated by high tumble swirl was made in this paper.
Cylinder pressure measurements were made simultaneously with measurement of flame arrival times and a heat release rate analysis was done. The 0-2 percent heat release duration was arbitrarily selected for comparison with flame arrival times at the spark plug windows. The 0-90 percent heat release duration was likewise arbitrarily selected for comparison with flame arrival times at the head gasket ionization probes. The comparison shows surprisingly good correlation. It also confirms that high tumble swirl head did not have a measurable effect on heat release durations, just as it did not have a measurable effect on flame arrival times.
CitationMeyer, R., Kubesh, J., Shahed, S., and Davis, J., "Simultaneous Application of Optical Spark Plug Probe and Head Gasket Ionization Probe to a Production Engine," SAE Technical Paper 930464, 1993, https://doi.org/10.4271/930464.
- Gallopoulos, N. “Bridging the Present to the Future in Personal Transportation - The Role of the Internal Combustion Engine,” SAE 920721
- Horowitz, A. Wascher, W. “Cold Weather Driveability Performance of Late Model Cars,” SAE 740520
- Heimrich, M.J. Albu, S. Osborne, J. “Electrically Heated Catalyst System Conversions on Two Current Technology Vehicles,” SAE 910612
- Whittenberger, W.A. Scheller, D.T. Walters, J. “Experiences with 20 User Vehicles Equipped with Electrically Heated Catalyst Systems - Part I,” SAE 920722
- Young, M.B. “Cyclic Dispersion in the Homogeneous Charge Spark Ignition Engine - A Literature Survey,” SAE 810020
- Pischinger, S. Heywood, J.B. “How Heat Loss to the Spark Plug Electrodes Affects Flame Kernel Development in an SI Engine,” SAE 900021
- Sztenderowicz, M. Heywood, J. “Mixture Non-Uniformity Effects on S.E. Engine Combustion Variability,” SAE 902142
- Witze, P.O. Hall, M.J. Wallace, J.S. “Fibre-Optic Instrumented Spark Plug for Measuring Early Flame Development in Spark Ignition Engines,” SAE 881638
- Hall, M.J. “The Influence of Fluid Motion on Flame Kernel Development and Cyclic Variation in a Spark Ignition Engine,” SAE 890991
- Kerstein, A.R. Witze, P.O. “Flame Kernel Model for Analysis of Fiber Optic Instrumented Spark Plug Data,” SAE 900022
- Witze, P.O. Hall, M.J. Bennett, M.J. “Cycle Measurement of Flame Kernel Growth and Motion Correlated with Combustion Duration,” SAE 900023
- Bianco, Y. Cheng, W.K. Heywood, J.B. “The Effect of Initial Flame Kernel Condition of Flame Development in SI Engines,” SAE 912402
- Lord, D.D. Kim, Y. Anderson, R.W. Brehob, D.D. “Fiber Optic Spark Plug Analysis of Early Flame Kernel Characteristics in Production Engines with Various Charge Motions,” SAE 930463
- Witze, P.O. “Cycle Resolved Multipoint Ionization Probe Measurements in a Spark Ignition Engine,” SAE 892099
- Witze, P.O. Bopp, S.C. “Investigation of In-Cylinder Fluid Motion Using Head Gaskets Instrumented with Ionization Probes,” SAE 910719
- Nicholson, D.E. Witze, P.O. “Flame Location Measurements in a Production Engine Using Ionization Probes Embodied in a Printed-Circuit-Board Head Gasket,” SAE 930390
- Gale, N. F. “Diesel Engine Cylinder Head Design: the Compromises and the Techniques,” SAE 900133
- Keck, J.C. Heywood, J.B. Noske, G. “Early Flame Development and Burning Rates in Spark Ignition Engines and Their Cyclic Variability,” SAE 870164