This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Preliminary Heat Release Analysis in a Single-Cylinder Two-Stroke Production Engine
Annotation ability available
Sector:
Language:
English
Abstract
The net heat release rate and net heat release fraction for a spark-ignited (SI) single-cylinder two-stroke, production engine were analyzed using the one-zone model. Three different throttle positions and four engine speeds for each position were considered for this study. The method used required cylinder pressure and crank-angle data which were obtained from a pressure transducer mounted in the cylinder head and a shaft encoder connected to the crankshaft. An effective routine referred to as the overlap method was used to smooth undesirable oscillations on the heat release rate curves after investigation of several different approaches. Parameters such as maximum heat release rate, rapid burn angle, combustion duration, maximum heat release rate angle, imep, bmep, etc. were calculated and discussed. It is shown that the trends for the results obtained by this simple model can be adequately explained using independent information regarding the effects of parameters such as residual burned mass fraction, equivalence ratio, and turbulence on flame burning speed. For not-too-rich mixture, a parameter is proposed to provide information regarding the short-circuiting in two-stroke engine. On this basis, “simple” one-zone heat release calculations can be used for rapid computations of important combustion-related parameters for engine analysis and diagnostics in two-stroke engines.
Two-stroke engines are being considered by auto-makers today as a possible alternative to the four-stroke engine because of their superior power-to-weight ratio, less number of parts, and smaller engine size. In the past, these engines were typically known to produce high levels of pollutants due to the scavenging of burned gases with the fresh incoming charge. But recent developments in electronic fuel injection have made it possible to overcome this problem, and to improve performance in other areas such as fuel consumption as well.
The more that is known about the combustion process, the easier it is to control it. One approach for examining the combustion process in an internal combustion engine is the heat release analysis. This provides valuable information on combustion behavior which is an important factor in fuel economy, engine performance, and emissions of harmful pollutants. Different models are used to analyze the heat release rate in engines. For example, Deshpande et al. (1) used a two-zone heat release model to calculate mass of the gases in the burned zone in a two-stroke engine. This was done by performing an energy balance on both the burned and unburned regions in the combustion chamber. The resulting equations were algebraic in nature requiring very little computer time. Consequently, a computer program using these equations could be employed for real time monitoring of the mass fraction burned behavior in a running engine. They also used this model to investigate the effects of the heat transfer term in the heat release rate equation on the mass fraction burned profile and found that it was negligible. Although it is generally understood that the two-zone model is more accurate, it has been shown by Chun and Heywood (2) that the fraction of fuel chemical energy released by combustion and the mass fraction of the air-fuel mixture burned can be estimated by a simpler one-zone model if an appropriate value for the “average ratio of specific heats”, γ (T), for the contents of the cylinder is chosen.
Based on the work of Rassweiler and Withrow (3), Abraham and Prakash (4) used a beat release analysis on their experimentally-obtained pressure-time histories to help them investigate causes of cyclic variations in a two-stroke engine. Their results suggested that cyclic variations depend primarily on the flame initiation period (the crank-angle duration from the spark to the point where 10% of the fuel mass is burned) due to variations of the mixture composition in the region where the spark occurs. They also concluded that the gross mixture quality, due to air/fuel ratio and incomplete mixing of fresh charge with residual gases, is not an important factor during the early phases of combustion. These conclusions were then tested analytically and confirmed using a thermodynamic model together with a model for turbulent flame propagation.
The amount of previous work in which a simple one-zone heat release model is used in a two-stroke SI engine is very limited. Hence, the purpose of this work is to investigate the usefulness of this “simple” model in a two-stroke engine by examining if the trends can be adequately explained using independent information regarding the effects of parameters such as residual burned mass fraction, equivalence ratio, and turbulence on flame burning speed. Other objective is to establish a basis from which further work can be done to improve the accuracy of the one-zone model for use with two-stroke engines.
Recommended Content
Authors
Topic
Citation
Rohrer, R. and Chehroudi, B., "Preliminary Heat Release Analysis in a Single-Cylinder Two-Stroke Production Engine," SAE Technical Paper 930431, 1993, https://doi.org/10.4271/930431.Also In
References
- Deshpande, S.R. Narasimhan, R. “Heat Release Analysis of a Two-Stroke Engine” SAE Paper 880175 1988
- Chun, K. M. Heywood, J.B. “Estimating Heat-Release and Mass-of-Mixture Burned from Spark-Ignition Engine Pressure Data,” Combustion Science and Technology 54 133 143 1987
- Rasseweiler, G.M. Withrow, L. Motion Pictures of Engine Flames Correlated with Pressure Cards,” SAE Trans 42 185 204 May 1938
- Abraham, M. Prakash, S. “A Theory of Cyclic Variations in Small Two-Stroke Cycle Spark Ignited Engines - Analytical Validation of Experimentally Observed Behaviour,” SAE Paper 920426 1992
- Mansouri, S.H. Heywood, J.B. “Correlation for the Viscosity and Prandtl Number of Hydrocarbon-Air Combustion Products,” Combustion Science and Technology 23 251 256 1980
- Lancaster, D. R. Krieger, R. B. Lienesch, J.H. “Measurement and Analysis of Engine Pressure Data,” SAE Paper 750026 1975
- Grimm B.M. Johnson R.T. “Review of Simple Heat Release Computations,” SAE Paper 900445 1990
- Heywood, J.B. Internal Combustion Engine Fundamentals MeGraw-Hill 1988
- Gatowski, J.A. Balles, E.N. Chun, K.M. Nelson, F.E. Ekehian, J.A. Heywood, J.B. “Heat Release Analysis of Engine Pressure Data,” SAE Paper 841359 SAE Trans. 93 1984
- Hires, S.D. Tabaczyriski, R.J. Novak, J.M. “The Prediction of Ignition Delay and Combustion Intervals for a Homogeneous Charge, Spark Ignition Engine,” SAE Paper 780232 SAE Trans. 87 1978
- Metghalchi, M. Keck, J.C. “Burning Velocities of Mixtures of Air with Methanol, Isooctane, and Indolene at High Pressure and Temperature” Combustion and Flame 48 191 210 1982
- Rhodes, D.B. Keck, J.C. “Laminar Burning Speed Measurements of Indolene-Air-Diluent Mixtures at High Pressures and Temperature,” SAE Paper 850047 1985