This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
An Evaluation of Interface Friction in Different Forming Models for Coated Steel Sheets
Annotation ability available
Sector:
Language:
English
Abstract
Interface friction between sheet metal and tooling in sheet metal forming is examined in different forming modes using laboratory simulative tests. Stretchability is studied by the limiting dome height test; drawability is investigated by a four inch Swift cup draw test and the coefficient of friction is measured by the draw bead simulator under bending and unbending deformation. The responses of the interface friction in six different coated and uncoated steel sheets are studied using seven different lubricants. It is found that the interface friction between sheet metal and tooling is very sensitive to the forming mode and the type of coating. For the same lubricant and coated material, two different forming modes may produce very different results in interface friction. However, overall good and bad lubricants for all forming modes can be determined for a given coated material using these three tests. These three tests are found to be very efficient and useful in the study of interface friction behavior of steel sheets in different forming modes.
Recommended Content
| Technical Paper | Frictional Characteristics of Galvanized Steels Evaluated with a Draw Bead Simulator |
| Technical Paper | The Effect of Zinc Coatings on the Formability of Automotive Sheet Steels |
Topic
Citation
Shi, M. and Meuleman, D., "An Evaluation of Interface Friction in Different Forming Models for Coated Steel Sheets," SAE Technical Paper 920633, 1992, https://doi.org/10.4271/920633.Also In
References
- “Intermaterial Competition for the Body in White of the Passenger Car” International Iron and Steel Institute Brussels 1990
- Meuleman D. J. Zoldak J. J. “The Interactions of Coated Steels, Die Materials and Forming Lubricants” SAE Paper No. 860432 1986
- Meuleman D. J. Dwyer T. E. “Die Materials and Treatments with Electrogalvanized Steels” SAE Paper No. 880369 1988
- Brazier W. G. Thompson R. W. “The Effect of Die Materials and Lubrication on Punch Stretching and Draw Forces of Cold Rolled and Zinc Coated Steels” SAE Paper No. 850274 1985
- Brazier W. G. Thompson R. W. “The Effect of Zinc Coating Die Materials and Lubricants on Sheet Metal Formability” SAE Paper No. 860434 1986
- Meuleman D. J. Denner S. G. Cheng F. V. “The Effect of Zinc Coatings on the Formability of Automotive Sheet Steels” SAE Paper No. 840370 1984
- Nine H. D. “Friction Measurement For Forming of Zinc-Based Coated Sheet Steel” in Zinc-Based Steel Coating System: Metallurgy and Performance Krauss G. Matlock D. K. 233 242 1990
- Keeler S. P. Nine H. D. Siekirk J. F. “Formability Criteria for Selecting Sheet Metal Lubricants” SAE Paper No. 880366 1988
- Shi M. F. Smith G. M. Moore M. Meuleman D.J. “Galvannealed Coating Optimized for Coating for Coating Adhesion through Dies” in Zinc-Based Steel Coating Systems: Metallurgy and Performance Krauss G. Matlock D. K. TMS 387 398 1990
- Kumpulainen J. O. “Factors Influencing Friction and Galling Behavior of Sheet Metals” Proc. of 13th IDDRG Melbourne, Australia 476 490 1984
- Hashimoto K. Ohwue T. Takita M. “Effect of Temperature, Die Materials and Lubricant on Sliding Behavior of Various Coated Steel Sheets” Proc. of 16th IDDRG Borlänge Sweden 153 160 1990
- Rangarajan V. Matlock D. K. Krauss G. “The Effects of Coating Properties on the Frictional Response of Zinc-Coated Sheet Steels” in Zinc-Based Steel Coating Systems: Metallurgy and Performance Krauss G. Matlock D. K. 263 280 1990
- Wojtowicz W. J. Lubrication Engineering 11 174 177 1955
- Nakayama M. Kanamaru T. Numakura Y. Yamada M. “Improvement of Press Formability of Precoated Sheet Steels by Lubricant” TABTECH INTERNATIONAL 89 Rosemont, Illinois 1989
- Sulonen M. Eskola P. Kampulainen J. Ranta-Eskola A. “A Reliable Method for Measuring the Friction Coefficient in Sheet Metal Forming” Proc. of IDDRG Working Group III 1981
- Duncan J. L. Shabel B. S. Gerbase Filho J. “A Tensile Strip Test for Evaluating Friction in Sheet Metal Forming” SAE Paper No. 780391 1978
- Nine H. D. “Drawbead Forces in Sheet Metal Forming” in Mechanics of Sheet Metal Forming: Behavior and Deformation Analysis Koistinen D. P. Wang N. M. New York, NY plenum press 179 211 1978
- Meuleman D. J. Siles J. L. Zoldak J. J. “The Limiting Dome Height Test for Assessing the Formability of Sheet Steel” SAE Paper No. 850005 1985
- Hecker S. S. “A Cup Test for Assessing Stretchability” Met. Engng. Quart. 14 30 1974
- Ghosh A. K. “The Effect of Lateral Drawing-in on Stretch Formability” Mat. Engng. Quart. 15 53 64 1975
- Chung S. Y. Swift H.W. “Cup Drawing From Flat Blank” Proc. Inst. Mech. Eng. London 65 1990 223 1951
- Chu E. Shi M.F. Gerdeen J. C. “Certain Aspects of the Limiting Drawing Ratio in Sheet Metal Forming Processes” Proc. of 15th IDDRG Dearborn, Michigan, USA 171 183 1988