This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Heavy Duty Drivetrains - The System and Component Application
Annotation ability available
Sector:
Language:
English
Abstract
Heavy truck drivetrains, while comprised of components produced by various manufacturers, must perform as an integrated system. The system has primary responsibility for transmitting engine power to the ground in a manner that will propel the vehicle over widely varying conditions. In doing so, it must provide long, trouble free life, while optimizing vehicle performance. The properly matched drivetrain system will complement the engine in minimizing vehicle fuel consumption.
Standardized component-to-vehicle and component-to-operator interfaces assist the vehicle manufacturer in simplifying his assembly process.
Humanistic consideration for driver comfort, and public health and safety further illustrate the necessity for matching and integrating drivetrain components into a system.
This paper addresses first, various system traits, then a detailed review of component considerations when matching components and integrating them into a drivetrain system.
Recommended Content
Technical Paper | Overview of an HVE Vehicle Database |
Technical Paper | Procurement and Development of the M715 1¼ Ton Truck Series |
Technical Paper | Statistical Amplitude Distribution Analyzer |
Authors
Topic
Citation
Jones, C., "Heavy Duty Drivetrains - The System and Component Application," SAE Technical Paper 910035, 1991, https://doi.org/10.4271/910035.Also In
Heavy Duty Drivetrains - The System and Component Application
Number: SP-0868; Published: 1991-02-01
Number: SP-0868; Published: 1991-02-01
References
- Hermanns, Martin J. “Heavy Duty, Long Life Dry Clutches” SAE Publication 700874 1970
- Willyard, John J. “Heavy Duty, Large Single Plate Diaphragm Spring Dry Clutches” SAE Publication 892976 1989
- Eaton Truck Components The Fuller Blue Book Eaton Corporation Kalamazoo 1981
- Buttermore, John R. 1991 SAE Buckendale unpublished material submittal Allison Transmission Division General Motors Corporation Indianapolis August 1990
- Ross, William A. “Designing a Hydromechanical Transmission for Heavy Duty Trucks” SAE Publication 720725 September 1972
- Fugoros, Bob “Series 60 Driveline Specification” 1991 SAE Buckendale unpublished material submittal Detroit Diesel Corporation Detroit June 1990
- Herman, Dan 1991 SAE Buckendale unpublished material submittal Navistar International Transportation Corporation Chicago 23 July 1990
- Fitch, James William Motor Truck Engineering Handbook Anacortes, Washington James W. Fitch Third 1984
- Smith, Gary L “Commercial Vehicle Performance and Fuel Economy” SAE Publication SP-355 16th L. Ray Buckendale Lecture 1970
- Focus T-Cape Publication Number PSM 15200 Navistar International Transportation Corporation Chicago January 1990
- Ford, Thomas F. Charles, Fred S. “Heavy Duty Truck Tire Engineering” SAE Publication SP-729 34th L. Ray Buckendale Lecture 1988
- Northrup, Thomas SAE staff 20 August 1990
- Performance, Formulas, Conversions, Tables, Graphs, Definitions Publication number SA 1309B Allison Transmission Division of General Motors Corporation Indianapolis August 1988
- Tables and Formulas Clark Axle and Transmission Division Buchanan 1979
- Deierlein, Bob “Maximizing Fuel Economy” Fleet Equipment February 1988
- Fugoros, Bob “Application Design Analysis Methods” 1991 SAE Buckendale unpublished material submittal Detroit Diesel Corporation Detroit June 1990
- Transmissions Publication number 1B-T Mack Trucks Inc. Allentown April 1988
- Deierlein, Bob “Fleet Feedback from Buyers and Specifiers-Fuel Economy” Fleet Equipment July 1989
- SAE Recommended Practice J 366 “Exterior Sound Level for Henry Trucks and Buses” February 1987
- Stadt, Richard L. “Truck Noise Control” SAE Publication SP-386 20th L. Ray Buckendale Lecture 1974
- Schetter, George Spicer Transmission Division, Dana Corporation 20 July 1990
- McCormick, Ernest J. Human Engineering New York McGraw-Hill 1957
- SAE Recommended Practice J/521 “Clutch Pedal Position”
- Pedue, Michael D. “Clutch Developments for Improved Vehicle Performance” SAE Truck and Bus meeting 1989
- “Rockwell Adds New Clutch Line” Southern Motor Cargo October 1988
- Kroemer, K.H. Eberhard “Pedal Operation by the Seated Operator” SAE Publication 720004 January 1972
- Stoneburner, Larry Spicer Clutch Division, Dana Corporation July 1990
- SAE Recommended Practice J 617C “Engine Flywheel Housings” June 1976
- SAE Recommended Practice J 618 “Flywheels for Single-Plate Spring Loaded Clutches” June 1980
- SAE Recommended Practice J 619 “Flywheels for Two Plate Spring Loaded Clutches” June 1980
- Engine Match Charts Publication number FUL-69-R5 Eaton Corporation, Transmission Division Kalamazoo April 1989
- Lubrication Specification for Spicer Transmissions Publication number 2508-11 Spicer Transmission Division, Dana Corporation Toledo March 1990
- Heavy Duty and Mid Range Lubrication Recommendations Publication number 121-R6 Eaton Corporation, Transmission Division Kalamazoo April 1988
- Engine-Converter Matching Technical Document number 148 Allison Transmission Division General Motor Corporation Indianapolis January 1990
- MT(B) 600 Series Installation Manual Technical Document number 102 Allison Transmission Division General Motors Corporation Indianapolis March 1989
- Mazziotti, Philip J “Dynamic Characteristics of Truck Driveline Systems” SAE Publication SP 262 11th L. Ray Buckendale Lecture 1964
- Holzinger, D.W. Powers, R.W. Lyons, J.M. “Application Parameters and Established Practices” Universal Joint and Driveshaft Design Manual SAE Publication AE-7 1979
- Joyner, Robert 1991 SAE Buckendale unpublished material submittal Spicer Universal Joint Division, Dana Corporation Toledo July 1990
- Wagner, E.R. “Duty Cycle Determination” Universal Joint and Driveshaft Design Manual SAE Publication AE-7 1979
- Wagner, E.R. Holzinger, D.W. Naegle, F.C. “Critical Speed” Universal Joint and Driveshaft Design Manual SAE Publication AE-7 1979
- SAE Recommended Practice J 901 “Universal Joints and Driveshafts-Nomenclature-Terminology-Application Guidelines” March 1985
- Multipiece Driveshaft Center Bearing Assemblies Publication number 3237-1 Spicer Universal Joint Division, Dana Corporation Toledo 1989
- Spicer-Life Universal Joint Kit Lube Specs Publication number 3306-3UJ Spicer Universal Joint Division, Dana Corporation Toledo January 1989
- Hansz, Frederich H. 1991 SAE Buckendale unpublished material submittal Automotive Operations, Rockwell International Corporation Troy, Michigan 20 August 1990
- Ecklund, William 1991 SAE Buckendale unpublished material submittal Eaton Corporation, Axle and Brake Division Kalamazoo 2 July 1990
- Eaton Axles and Brakes Service Manual EA-42 Eaton Corporation, Axle and Brake Division Kalamazoo November 1983
- Wagner, E.R. “Axle Driveshafts” Universal Joint and Driveshaft Design Manual SAE Publication AE-7 1979
- Lubrication Publication number FMM-1 Rockwell International Corporation Troy, Michigan March 1985
- Wallace, Richard G. 26 June 1990
- SAE Recommended Practice J 704 “Openings for Six-and Eight-Bolt Truck Transmission Mounted Power-Take-Offs” June 1983
- SAE Recommended Practice J 772 “Clearance Envelopes for Six-and Eight-Bolt Truck Transmission Mounted Power Take-Offs” November 1983
- Chelsea Power Take-Off Service Guide-Understanding the PTO Publication number P1-2-DSD Drivetrain Services Division, Dana Corporation Toledo 1981
- “Product Showcase - Retarders” Heavy Duty Trucking February 1990