This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Deposits in Gasoline Engines - A Literature Review
Annotation ability available
Sector:
Language:
English
Abstract
This paper reviews the literature on deposits that form on all internal surfaces coming into contact with the fuel in a gasoline engine. It does not consider deposits that can form in areas primarily affected by the engine lubricant. The physical, and especially the chemical, mechanisms that lead to deposit formation are very complex and poorly understood, and are different in different parts of the engine. Deposits can impair engine operation in terms of fuel economy, power emissions, octane requirement and driveability. In the worst cases they could lead to engine damage. Deposits in most parts of the engine can be controlled through the use of fuel additives. Test procedures used in deposit-related studies are characterised by poor repeatability and reproducibility because of the complex nature of the processes involved. Deposit formation and, consequently, the effectiveness of deposit control additives also depend on base fuel properties and engine design and operation.
Recommended Content
| Technical Paper | Effects of Fuel Corrosion Inhibitors on Powertrain Intake Valve Deposits |
| Technical Paper | Gasoline Quality And Its Effects on Intake System Deposits |
Authors
Topic
Citation
Kalghatgi, G., "Deposits in Gasoline Engines - A Literature Review," SAE Technical Paper 902105, 1990, https://doi.org/10.4271/902105.Also In
References
- Heywood, J.B. “Internal combustion engine fundamentals” McGraw Hill Book Co. 1988
- Sigworth, H.W. Payne, J.Q. “The cause and correction of carburetor gumming” SAE National Fuels and Lubricants Meeting Tulsa, OK 1954
- Retzloff, J.B. Plonsker, L. Sneed, R.B. “Fuels detergency-effects on emissions” SAE Paper No. 720841 1972
- Ebersole, G.D. Holman, G.E. “Lubricant - closed PCV system relationships influence exhaust emission” SAE Paper No. 680113 1968
- Hall, D.W. Gibbs, L.M. “Carburetor deposits - are clean throttle bodies enough?” SAE Paper NO. 760752 1976
- Tupa, R.C. Koehler, D.E. “Gasoline port fuel injectors - keep clean/clean up with additives” SAE Paper No. 861536 SP-713 Deposit formation in gasoline fuel injected engines SAE 1986
- Benson, J.D. Yaccarino, P. “Fuel and additive effects on multiport fuel injector deposits” SAE Paper No. 861533 SP-713 1986
- Taniguchi, B.Y. Peyla, R.J. Parsons, G.M. Hoekman, S.K. Voss, D.A. “Injector deposits - the tip of intake system deposit problems.” SAE Paper No. 861534 SP-713 1986
- Rogers, D.T. Jonach, F.L. “Mechanism of intake valve underside deposit formation” SAE Paper No. 106C SAE National Fuels and Lubricants Meeting Tulsa, OK Nov. 1958
- Jewitt, C.H. Bostick, G.L. Kersey, V.L. “Fuel Injector, intake valve and carburetor detergency performance of gasoline additives” SAE Paper No. 872114 1987
- Mikkonen, S. Karlsson, R. Jouni, K. “Intake valve sticking in some carburetor engines” SAE Paper No. 881643 1988
- Swain, M.R. Swain, M.N. Blanco, J.G. Adt, R.R. “The effect of alternative gasolines on knock and intake valve sticking” SAE Paper No. 872040 1987
- Gibbs, L.M. Pereira, N.F. “Does unleaded gasoline need a deposit control additive?” National Petroleum Refiners Association Paper No. F&L-73-52 1973
- Lewis, R.A. Newhall, H.K. Peyla, R.J. Voss, D.A. Westland, J.S. “A new concept in deposit control additives for unleaded gasolines.” JSAE paper No. 830938 1983
- Graiff, L.B. “Some new aspects of deposit effects on engine octane requirement increase and fuel economy” SAE Paper No. 790938 1979
- Gething J.A. “Performance robbing aspects of intake valve and port deposits” SAE Paper No. 872116 1987
- Niewhauve, B. Giere, G. Gondermann, H. “Requirements for modern gasoline additives and their testing” Journal Erdol und Kohle Erdgas, Petrochemie 649 674 1978/79
- Bitting, W. Gschwendtner, F. Kohlepp, W. Kothe, M. Testvoet, C.J. Ziwica, K.H. “Intake valve deposits - fuel detergency requirements revisited” SAE Paper No. 872117 1987
- “Proceedings of the CRC workshop on intake valve deposits” August 22-24 1989 San Fransisco Co-ordinating Research Council 1989
- Eng. K.D. Carlson, C.A. Haydn, T.E. Sung, R.L. “Engine test procedures to evaluate octane requirement increase and intake system cleanliness” SAE Paper No. 892122 SP-794 Fuel and Induction System Deposits SAE 1989
- Adams, K.M. Baker, R.E. “Effects of combustion chamber deposits location and composition” “Chemistry of engine combustion deposits” Ebert, L.B. 19 37 Plenum Press 1985
- Benson, J.D. “Some factors which affect octane requirement increase” SAE Paper No. 750933 1975
- Greenshields, R.J. “Spark plug fouling tendencies” SAE Trans. 61 3 1953
- Kalghatgi, G.T. “Improvement in early flame development in a spark ignition engine brought about by spark aider fuel additives” Combust.Sci.Tech. 52 427 1987
- Kalghatgi, G.T. “Improvement in the ignition ability of glow discharges brought about by deposits of potassium sulphate on the electrodes” Paper No. C50/88 International Conference on Combustion in Engines - Technology and Applications I.Mech.E. London 1988
- Kalghatgi, G.T. “Flame initiation and development from glow discharges - Effect of electrode deposits” Combustion and Flame 77 321 1989
- Kalghatgi, G.T. “Effect of a spark aider fuel additive on the misfire characteristics of a spark ignition engine” Combustion Sci. Tech. 62 1 1989
- Blackmore, D.R. Graiff, L.B. Harrow, G.A. Jones, J.M. Kalghatgi, G.T. Miles, R. “Development of a novel gasoline additive: laboratory test work” Paper C311/86 I.Mech.E. 1986
- Kipp, K.L. Ingamells, J.C. Richardson, W.L. Davis C.E. “Ability of gasoline additives to clean engines and reduce exhaust emissions” SAE Paper No. 700456 1970
- Neveu, C. Lukaschek, G. Hamblin, P.C. Boettcher, W. Saville, S.B. “Sludge formation in gasoline engines - a literature survey” 3rd CEC Symposium “Performance evaluation of automotive fuels and lubricants” Paris 19-21 April 1988
- Greber, A.F. Smith, R.G. “Some effects of exhaust gas recirculation upon automotive engine intake system deposits and crankcase lubricant performance” SAE Paper No. 710142 1971
- Marbach, H.W. Johnston, A.A. Bowden, J.N. LePera, M.E. “A novel laboratory method for evaluating induction system deposits in gasoline engines” SAE Paper No. 790204 1979
- Hilden, D.L. “The relationship of gasoline diolefin content to deposits in multiport fuel injectors” SAE Paper No. 881642 1988
- Kim, C Tseregounis, S.I. Scruggs, B.E. “Deposit formation on a metal surface in oxidised gasolines” SAE Paper No. 872112 1987
- Tseregounis, S.I. “Thin deposit films from oxidised gasoline on steel surfaces as determined by ESCA” SAE Paper No. 881641 1988
- Kolobielski, M. McCaleb, F. “Gasolines and engine oils: Literature review, new laboratory oxidation method and significance of olefins in fuel” Report No. 2296 U.S. Army MERD Command Fort Belvoir, Va. Government Accession No. ADA 086740
- Nishizaki, T. Maeda, Y. Date, K. Maeda, T. “The effect of fuel composition and fuel additives on intake system detergency of Japanese automobile engine” SAE Paper No. 790203 1979
- Coordinating Research Council Inc. “Carburetor Cleanliness test procedure: State-of-the-art summary report: 1973-1981” CRC Inc. 219 Perimeter Centre, Parkway, Atlanta 1983
- Malakar, J.J. Retzloff, J.B. Gibbs, L.M. “Throttle body deposits - the CRC carburetor cleanliness test procedure.” SAE Paper No. 831708 CRC Report No. 529 1983
- Gibbs, L.M. Richardson, C.E. “Carburetor deposits and their control” SAE Paper No. 790202
- Franklin, T.M. Stambaugh, R.L. Kuhn, R.R. “Simulated road test evaluation of the effect of gasoline additives on exhaust gas emissions” SAE Paper No. 720942 1972
- Tupa, R.C. “Port fuel injector deposits: causes/consequences/cures” SAE Paper No. 872113 SP-725 1987
- Abramo, G.P. Horowitz, A.M. Trewella, J.C “Port fuel injector cleanliness studies” SAE Paper No. 861535 SP-713 1986
- Caracciolo, F Stebar, R.F. “An engine dynamometer test for evaluating port fuel injector plugging” SAE Paper No. 872111 SP-725 Deposits in Modern Engines SAE 1987
- Lenane, D.L. Stocky, T.P. “Gasoline additives solve injector deposit problems” SAE Paper No. 861537 SP-713 1986
- Tupa, R.C. Taniguchi, B.Y. Benson, J.D. “A vehicle test technique for studying port fuel injection deposits - A coordinating Research Council Program” SAE Paper No. 890213 1989
- Richardson, C.B. Gyorog, D.A. Beard L.K. “A laboratory test for fuel injector deposit studies” SAE Paper No. 892116 SP-797 1989
- CRC “Intake manifold deposit engine dynamometer test procedure. State-of-the-art summary report. 1973-1978” CRC Report No. 505 CRC Inc. April 1979
- Siegel, W.O. Zinbo, M. “On the chemical composition and origin of engine deposits” Chemistry of Engine Combustion deposits Ebert, L.B. 53 Plenum Press 1985
- Esaki, Y. Ishiguro, T. Suzuki, N. Nakada, M. “Mechanism of intake valve deposit formation Part 1: Characterisation of deposits” SAE Paper No. 900151 1990
- Lepperhoff, G. Schommers, J. “Mechanism of deposit formation at inlet valves” SAE Paper No. 872115 1987
- Tomita, M. Okada, M. Katayama, H. Nakada, M. “Effect of gasoline quality on throttle response of engines during warm-up.” SAE Paper No. 900163 1990
- Starke, L. Schwartz, E. 1982
- Alquist, H.E. Holman, G.E. Wimmer, D.B. “Some observations of factors affecting ORI” SAE Paper No. 750932 1975
- Bond, T.J. Gerry, F.S. Wagner, W. “Intake valve deposit control - a laboratory programme to optimise fuel/additive performance” SAE Paper No. 892115 SP-797 1989
- Polss, P. “What additives do for gasoline” Hydrocarbon Processing Feb 1973
- Gartenman, E. “Effectiveness of petrol additives for the maintenance of clean intake systems in internal combustion engines” Material und Technik 2 92 97 1981
- Gohn, M.R. “Evaluating gasoline additives for intake-valve cleanliness using the Volkswagen Polo engine” SAE Paper No. 892118 SP-797 1989
- Mikkonen, S. Niemi, A. Niemi, C. Niskala, J. “Effect of engine oil on intake valve deposits” SAE Paper No. 892111 1989
- Daneshgari, P. “A test procedure for identifying the gasoline's deposit formation tendency on intake valve” SAE Paper No. 892120 SP-797 1989
- Daneshgari, P. Borgman, K. Job, H. “The influence of temperature upon gasoline deposit build-up on the intake valves” SAE Paper No. 890215 1989
- Dimitroff, E Johnston, A. “Mechanism of induction system deposit formation” SAE Paper No. 660784 1966
- Bailey, B.K. Stavinoha, L.L. Present D.L. “Gasoline deposit mechanism on aluminium at various temperatures” SAE Paper No. 892117 1989
- Nomura, Y. Oshawa, K. Ishiguro, T. Nakada, M. “Mechanism of intake valve deposit formation Part 2: Simulation tests” SAE Paper No. 900152 1990
- Ebert, L.B. “Chemistry of engine combustion deposits - literature review in chemistry of engine combustion deposits” Ebert, L.B. 3 18 Plenum Press 1985
- Gebhardt, L.A. Lunt, R.S. Silbernagel B.G. “Electron spin resonance studies of internal combustion engine deposits” in chemistry of engine combustion deposits” Ebert, L.B. Plenum Press 145 175 1985
- Shore, L.B. Ockert, K.F. “Combustion chamber deposits - a radio tracer study” SAE Transactions 66 285 294 1958
- Lauer, J.L. Friel, P.J. “Some properties of carbonaceous deposits accumulated in internal combustion engines” Combust. Flame 4 107 1960
- Chapman, J.L. Williamson, J. Preston, W.H. “Deposits in internal combustion engines” Deposition from Combustion Gases Jones A.R. 113 127 IOP Publishing Ltd Bristol, UK 1989
- Dumont, L.F. “Possible mechanisms by which combustion chamber deposits accumulate and influence knock” SAE Quart. Trans. 5 565 576 1951
- Warren, J. “Combustion chamber deposits and octane number requirement” SAE Transactions 62 583 1954
- Duckworth, J.B. “Effects of combustion chamber deposits on octane requirement and engine power output” SAE Quarterly Transactions 5 571 583 1951
- Nakamura, Y Yonekawa, Y Okamoto, N. “The effect of combustion chamber deposits on octane requirement increase and fuel economy” Chemistry of engine combustion deposits Ebert, L.B. 199 211 Plenum Press 1985
- Yonekawa, Y. Nakamura, Y. Okamoto, N. “The study of combustion chamber deposits (Part 4) - Octane number requirement and fuel economy with deposit build up” J. Japan Petrol Inst. 25 173 176 1982
- Harder, R.F. Anderson, C.L. “Investigation of combustion chamber deposit thermal behaviour utilising optical radiation measurements in a fired engine” Combust. Sci. Tech. 60 423 439 1988
- Nishiwaki, K. “Unsteady thermal behaviour of engine combustion deposits” SAE Paper No. 881225 1988
- Hayes, T.K. Peters J.E White R.A. “The thermal properties of engine deposits and their effect on combustion chamber heat transfer” Proceedings of the 2nd Int. Conf. on New Developments in Powertrain and Chassis Engineering Strassbourg June 1989 I.Mech.E. 1989
- Overbye, V.D. Bennethum, J.E. Uyehara, O.A. Myers P.S. “Unsteady heat transfer in engines” Transactions of the SAE 69 461 494 1961
- Keller, B.D. Meguerin, G.H. Tracy, C.B. Smith J.B. “ORI of today's vehicles” SAE Paper No. 760195 1976
- Cooperative Octane Requirement Committee (CORC) “The effect of removing lead alkyl from European motor gasoline” October 1972
- Bachman, H.E. Prestridge, E.B. “The use of combustion deposit analysis for studying lubricant induced ORI” SAE Paper No. 750938 1975
- Ebert, L.B. Davis, W.H. Mills, D.R. Dannerlein, Di Rose, D.L. Melchior, M.T. “The chemistry of internal combustion engine deposits - Part I, II and III” chemistry of Engine combustion deposits Ebert, L.B. 71 144 Plenum Press 1985
- Spindt, R.S. Wolfe, C.L. Stevens, D.R. “Nitrogen oxides, combustion and engine deposits” SAE Transactions 64 797 1956
- Newby, W.E. “Emphasises the effect boiling point on deposit formation” SAE Transactions 66 294 1958
- Myers, P.S. Uyehara, O.A. DeYoung, R. “Fuel composition and vaporization effects on combustion chamber deposits” U.S. Dept. of Energy. Report No. DOE/CS/50020--1 December 1981
- Mikita, J.J. Sturgis, B.M. “The chemistry of combustion chamber deposits” proceedings of the 4th World Congress 357 376 Rome 1956
- Kunc, J.F. “Effect of lubricating oil on octane requirement increase” SAE Quart. Trans. 5 582 1951
- McNab, J.B. Moody, L.E. Hakala, N.V. “Effect of lubricant composition on combustion chamber deposits” SAE Transactions 62 228 242 1954
- Tsukasaki, M. Yasuda, A. Ito, S. Nohira, H. “Study of mileage related formaldehyde emission from methanol fueled vehicles.” SAE Paper No. 900705 1990
- Lee, R.C. Thomas, S.P. “Some lubricant effects on octane requirement increase” Div. Petr. Chem. Amer. Soc. 23 974 1978
- Maricante, A. Chiampo, P. “Influence of lubricating oil ash on the ORI of engines running on unleaded fuel” SAE Paper No. 720945 1972
- Coordinating Research Council (CRC) Report No. 531 “Octane Requirement Increase of 1980 model cars” 1982
- Callison, J.C. Wusz, T. Biller, W.F. “Trends in octane number requirements (ONR) increase” SAE Paper No. 892036 1989
- Van Paassen, C.W.C. “Changing refining practice to meet gasoline and diesel demand and specifications requirements” Paper No. C316/86 25 “International Conference on petroleum based fuels and automotive applications” I.Mech.E. Conference Publications 1986
- Dabelstein, W.E.A. Reglitzky, A.A. McArragher, J.S. “ A quality/quantity survey of the European situation” SAE Paper No. 861585 1986
- Saillant, R.B. Pedrys, F.J. Kidder, H.E. “More data on ORI variables” SAE Paper No. 760195 1976
- Niles, H.T. McConnell, R.J. Roberts, M.A. Saillant, R. “Establishment of ORI characteristics as a function of selected fuels and engine families” SAE Paper No. 750451 1975
- Coordinating Research Council Report No. 445 “Influence of leaded and unleaded fuels on octane requirement increase in 1971 model cars” CRC Inc. Atlanta March 1971
- Hughes, E.C. “Discusses catalytic effects of deposits on combustion” SAE Transactions 62 592 1954
- Retailliau, E.R. Ricards, H.A. Jones, M.C.K. “Pre combustion reactions in a spark ignition engine” SAE Quart. Trans. 4 438 454 1950
- Yonekawa, Y. Kokubo, K. Nakamura, Y. Okamoto, N. “The study of combustion chamber deposit (Part 5) - The role of combustion chamber deposits in fuel economy” J. Japan Petrol Inst. 25 177 182 1982
- Bradish, J.P. Myers P.S Uyehara, O.A. “Effect of deposit properties on volumetric efficiency, heat transfer and preignition in internal combustion engines” SAE Paper No. 660130 1966
- DeGregoria, A.J. “A theoretical study of engine deposit and its effect on octane requirement using an engine simulation” SAE Paper No. 820072 1982
- Harrow, G.A. Orman, P.L. “Study of flame propagation and cyclic dispersion in a spark ignition engine” ASAE Symposium on Combustion in Engines July 1965 Advances in Automobile Engineering 3 27 Pergamon Press 1966
- Bert, J.A. Gething, J.A. Hansel, T.J. Newhall, H.K. Peyla, R.J. Voss, D.A. “Authors' closure to discussion, SAE Paper No. 831709,” SAE Transactions 1983
- Graiff, L.B. “Fuel related factors affecting engine octane requirements” chemistry of engine combustion deposits Ebert, L.B. 39 51 Plenum Press 1985
- Hoult, D.P. Hamiroune, D. Keck, J.C. “Heat transfer in the end gas” SAE Paper No. 870168 1987
- Gagliardi, J.C. Ghannam, F.E. “Effects of tetraethyl lead concentration on exhaust emissions in customer type vehicle operation” SAE Paper No. 690015 1969
- Dable, J.W. Sheahan, T. “The contribution of additives to the elimination of air pollution” Proc. Instn. Mech. Eng. Paper No. C128/71 62 71 1971
- Gagliardi, J.C. “The effect of fuel anti-knock compounds and deposits on exhaust emissions” SAE Paper No. 670128 1967
- Pahnke, A.J. Conte J.F. “Effect of combustion chamber deposits and driving conditions on vehicle exhaust emissions” SAE Paper No. 690017 1969
- Liekkannen, H.E. Beckman, E.W. “The effect of leaded and unleaded gasolines on exhaust emission as influenced by combustion chamber deposits” SAE Paper 710843 1971
- Adamczyck, A.A Kach, R.A. “The effect of engine deposit layers on hydrocarbon emissions from closed vessel combustion” Combust. Sci. Tech 47 193 212 1986
- Huls, T.A. Nickol, H.A. “Influence of engine variables on exhaust oxides of nitrogen concentrations from a multicylinder engine SAE Paper No. 670482 1967
- Amberg, G.H. Craig, W.S. “Gasoline detergents control intake system deposits” SAE Paper No. 554D 1962
- Tupa, R.C. Koehler, D.E. “Intake valve deposits - effects of engines, fuels and additives” SAE Paper No. 881645 1988
- Enoch, O. “Lists effects of deposits on power at retarded spark” SAE Trans. 62 593 1954
- Wheeler, R.W. “Abnormal combustion effects on economy” “Fuel economy in road vehicles powered by spark ignition engines” Hilliard, J.C. Springer G.S. Plenum Press New York 1984
- Bert, J.A. Gething, J.A. Hansel, T.J. Newhall, H.K. Peyla, R.J. Voss, D.A. “A gasoline additive concentrate removes combustion chamber deposits and reduces vehicle octane requirements” SAE Paper No. 831709
- Asseff, P.A. “Multifunctional gasoline additives reduce engine deposits” SAE Paper No. 660543 1966
- Sheahan, T.J. Dorer, C.J. Miller, C.O. “Detergent-dispersant fuel performance and handling” SAE Paper No. 690516
- Tupa, R.C. Dorer, C.J. “Gasoline and diesel fuel additives for performance/distribution/quality - II” SAE Paper No. 861179 1986
- Gibbs, L.M. Lewis, R.A. Voss, D.A. Jones, D.R. “Chevron experience with a new deposit control gasoline” Paper No. FL-79-109 1979 National Fuels and Lubricants Meeting of the National Petroleum Refiners Association Houston Nov. 1979
- Udelhofen, J.M. Zahalka, T.L. “Gasoline additive requirements for today's smaller engines” SAE Paper No. 881644 1988
- Sturgis, B.M. “Additives in petroleum fuels - a decade of progress” ACS symposium on a Decade of Progress in Petroleum Technology 6 3 51 66 1961
- Daneshgari, P. Schafer, H.V. “The influence of gasoline components on intake valve coking” MTZ, Motortechnische Zeitschrift 49 10 397 402 1988
- Barusch, M.R. Mingle, J.G. Payne, J.Q Sigworth, H.W. “The world's first detergent action gasoline with 36 years of perspectives” SAE Paper No. 900149 1990
- Mixon, L.W. Rozmanith, A.I. Wotring, W.T. “Effect of fuel and lubricant additives on exhaust emissions” SAE Paper No. 710295 1971
- Nelson, O.L. Larson, J.E. Fein, R.S Fuller, D.D Rightmire, G.K. Krumm, R.W. Ducker, G.E. “A broad-spectrum, non-metallic additive for gasoline and diesel fuels: performance in gasoline engines” SAE Paper No. 890214 1989
- Emelyanov, V.E. Kyuregyan, S.K. Rudyak, K.B “Laboratory method for rating the effectiveness of detergent additives in automotive gasolines” Translated from Khimiya: Tekhologiya Topliv: Masel 8 40 42 1981
- Toft, G.B. Hall, C.S. -A semi-automated carburetter cleanliness test” Fourth Int. Symp. on Engine Testing. Automation, Performance, Emission and Diagnostics Naples 1975
- Smith, R.G. Doelling, R.P. “An evaluation technique for gasoline carburetter detergents” SAE Paper No. 700669 1970
- Coordinating Research Council Inc. “CRC carburetor and induction system rating manual, No. 16” CRC Inc. 219 Perimeter Centre, Parkway, Atlanta, Ga. 1987
- Coordinating European Council “The evaluation of gasoline engine intake system deposition” CEC F-04-A-87 CEC 61 New Cavendish Street, London 1988
- Coordinating European Council “CEC Round Robin Test 88” SF1/Ope1 Kadett/RR 89 CEC 61 New Cavendish Street, London 1989
- Coordinating European Council Test Procedure CEC/FO3/T/81 CEC 61 New Cavendish Street, London 1981
- Johnston, A.A. Dimitroff, E. “A bench technique for evaluating the induction system deposit tendencies of motor gasoline” SAE Paper No. 660783 1966
- Heilmann, G. Seifert, K.H. “DKA - Projektgruppe “Intake system cleanliness” Prufung von Kraftstoffzusatzen” 10 1081 1101 1976
- CRC “Development of a laboratory test for multiport fuel injector deposits - E” Rep. No. AD-A191 313 Dec. 1987
- Hall, C.A. “Effect of TEL concentration on rate-of-requirement increase” SAE Quart Trans 5 581 1951
- BTC Octane Requirement and High Speed Knock Working Group “Draft ORI code of practice - Bench Tests” Nov. 1988
- Cooperative Octane Requirement Committee (CORC) “Technique for determining road octane requirements under accelerating and constant speed conditions” 1987
- Coordinating Research Council “Technique for determination of octane number requirement of light duty, vehicles, attachment to CRC Report No. 561 CRC Atlanta 1988
- Corner, E.S. Hochauser, A.M. Shannon, M.F. “Technical vs customer knock satisfaction - Two decades” SAE Paper No. 780322 1978