This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Design of Blue Tooth Controlled Robotic Arm and Development through Fused Deposition Modelling process
Technical Paper
2022-28-0565
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Additive manufacturing produces parts by adding material layer by layer with respect to time based on a computerized 3D solid model. The design model of Robotic arm was prepared using the solid works. The various components such as fingers, gripper, etc., were created and connected. After meticulous mathematical calculations, the design features of the robotic arm, including force analysis, are arrived at, and the arm is prepared to be operated using Bluetooth. Major challenges were faced during conversion of the designed model to prototype model. Furthermore, the components were created utilising fast rapid prototyping, which is more efficient than other traditional approaches. This technology has been effectively used in the production of light weight prototypes, tooling and the development low-cost bespoke designs. Finally, all the parts are assembled with Bluetooth control systems and validated with payload up to maximum of 10kgfor lowering and lifting.
Authors
- Nakandhrakumar Ramaswamy - Hindustan Institute of Tech. & Science
- Sangeethkumar Elumalai - Hindustan Institute of Tech. & Science
- Swapnanil Goswami - Hindustan Institute of Tech.& Science
- Selvakumar Raja - Hindustan Institute of Tech.& Science
- Ramanathan Velmurugan - Hindustan Institute of Tech.& Science
- Vutti Venkata Goutham - Hindustan Institute of Tech.& Science
- M Ramakrishnan - Hindustan Institute of Tech.& Science
Citation
Ramaswamy, N., Elumalai, S., Goswami, S., Raja, S. et al., "Design of Blue Tooth Controlled Robotic Arm and Development through Fused Deposition Modelling process," SAE Technical Paper 2022-28-0565, 2022, https://doi.org/10.4271/2022-28-0565.Also In
References
- Huang , S.H. , Liu , P. , Mokasdar , A. , and Hou , L. Additive Manufacturing and Its Societal Impact: A Literature Review The International Journal of Advanced Manufacturing Technology 67 5 2013 1191 1203
- Talpur , M.S.H. and Shaikh , M.H. 2012
- Houda , K. and Lakel , R. Synchronized Communication in a Set of Autonomous Mobile Robots Using Bluetooth Technology Procedia Computer Science 73 2015 154 161
- Kumar , R. , Ushapreethi , P. , Kubade , P.R. , and Kulkarni , H.B. Android Phone Controlled Bluetooth Robot International Research Journal of Engineering and Technology (IRJET) 3 4 2016 104 114
- Papcun , P. , Zolotova , I. , and Tafsi , K. Control and Teleoperation of Robot Khepera via Android Mobile Device through Bluetooth and Wifi IFAC-PapersOnLine 49 25 2016 188 193
- Jabir , M. , John , N. , Fayas , M. , Mohan , M. et al. Wireless Control of Pick and Place Robotic Arm Using an Android Application International Journal of Advanced Research in Electrical, Electronics and Instrumentation Engineering 4 2015 2410 2416
- Butkar , V.D. , Devikar , S.R. , Jaybhaye , V.B. , and Shilpa , P. Android Based Pick and Place and Place Robot International Journal of Informative and Futuristic Research 2 2014 859 867
- Lanzotti , A. , Grasso , M. , Staiano , G. , and Martorelli , M. The Impact of Process Parameters on Mechanical Properties of Parts Fabricated in PLA with an Open-Source 3-D Printer Rapid Prototyping Journal 2015
- Matsuzaki , R. , Ueda , M. , Namiki , M. , Jeong , T.-K. et al. Three-Dimensional Printing of Continuous-Fiber Composites by In-Nozzle Impregnation Scientific Reports 6 1 2016 1 7
- Putame , G. , Terzini , M. , Carbonaro , D. , Pisani , G. et al. Application of 3D Printing Technology for Design and Manufacturing of Customized Components for a Mechanical Stretching Bioreactor Journal of Healthcare Engineering 2019 2019