This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Delamination Failure on High-Output Diesel Engine Thermal Barrier Coatings
Technical Paper
2022-01-0440
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
An analytical mechanics model was employed to predict the delamination of several thermal-barrier-coated pistons that had been previously tested in a high-output, single-cylinder diesel engine. Some of the coatings delaminated during engine operation. Results are presented for two thicknesses of the same coating material, and for two similar coatings with different levels of stiffness. All the coating thermomechanical properties such as thermal conductivity, density, volumetric heat capacity, thickness, elastic modulus, coefficient of thermal expansion, Poisson ratio and toughness, were measured prior to engine testing. Previous measurements of the piston transient heat flux, based on fast-response surface temperature data, in the same engine were used as an input to calculate the multilayer wall temperature distribution. A theoretical methodology was employed to evaluate and predict the coating durability. The method considers the release rate of elastic strain energy stored in the coating when it cracks as the main driving force for delamination; when the calculated energy release rate overcomes the toughness, coating crack failure is predicted to occur. The mechanics durability model was found to provide good trendwise comparison with the post-run coating integrity observations. When the energy release rate significantly exceeded the toughness, failure was indeed observed. Borderline cases, where the energy release rate was close to the material toughness, however, were more difficult to predict.
Authors
Topic
Citation
Koutsakis, G., Saputo, J., Gingrich, E., Tess, M. et al., "Delamination Failure on High-Output Diesel Engine Thermal Barrier Coatings," SAE Technical Paper 2022-01-0440, 2022, https://doi.org/10.4271/2022-01-0440.Also In
References
- Siegla , D.C. and Alkidas , A.C. Evaluation of the Potential of a Low-Heat-Rejection Diesel Engine to Meet Future EPA Heavy-Duty Emission Standards SAE Transactions 98 1989 294 302
- Assanis , D.N. , Wiese , K. , Schwarz , E. , and Bryzik , W. The Effects of Ceramic Coatings on Diesel Engine Performance and Exhaust Emissions SAE Technical Paper 910460 1 1991 10.4271/910460
- Tricoire , A. , Kjellman , B. , Wigren , J. , Vanvolsem , M. et al. Insulated Piston Heads for Diesel Engines Journal of Thermal Spray Technology 18 2 2009 217 222
- Kamo , R. , Bryzik , W. , Reid , M. , and Woods , M. Coatings for Improving Engine Performance SAE Transactions 1997 354 363
- Siegla , D.C. and Amann , C.A. Exploratory Study of the Low-Heat-Rejection Diesel for Passenger-Car Application SAE Transactions 1984 259 283
- Vittal , M. , Borek , J. , Marks , D. , Boehman , A. et al. The Effects of Thermal Barrier Coatings on Diesel Engine Emissions Journal of Engineering for Gas Turbines and Power 1999
- Kvernes , I. , Fartum , P. , and Henriksen , R. Development and Engine Testing of Coatings on Diesel Engine Components Central Inst. for Industrial Research, Oslo (Norway) 1979
- Kamo , R. Adiabatic Turbocompound Engine Performance Prediction SAE Technical Paper 780068 1978 10.4271/780068
- Beardsley , M.B. , Socie , D. , Redja , E. , and Berndt , C. 2006
- Beardsley , M.B. Potential Use of Quasicrystalline Materials as Thermal Barrier Coatings for Diesel Engine Components Iowa State University 2008
- Yonushonis , T.M. Thick Thermal Barrier Coatings for Diesel Components NASA Lewis Research Center 1991
- Saad , D. , Saad , P. , Kamo , L. , Mekari , M. et al. Thermal Barrier Coatings for High Output Turbocharged Diesel Engine SAE Technical Paper 2007-01-1442 2007 10.4271/2007-01-1442
- Uchida , N. and Osada , H. A New Piston Insulation Concept for Heavy-Duty Diesel Engines to Reduce Heat Loss from the Wall SAE International Journal of Engines 10 5 2017 2565 2574
- Schaedler , T. , Andruskiewicz , P. , Durrett , R. , Najt , P. et al. Temperature-Following Thermal Barrier Coatings for High Efficiency Engines DOE Vehicle Technologies Annual Merit Review 2018
- Thibblin , A. and Olofsson , U. A Study of Suspension Plasma-Sprayed Insulated Pistons Evaluated in a Heavy-Duty Diesel Engine International Journal of Engine Research 21 6 2020 987 997
- Yan , Z. , Gainey , B. , Gohn , J. , Hariharan , D. et al. The Effects of Thick Thermal Barrier Coatings on Low-Temperature Combustion SAE International Journal of Advances and Current Practices in Mobility 2 2020-01-0275 2020 1786 1799
- Morel , T. , Keribar , R. , and Blumberg , P.N. Cyclical Thermal Phenomena in Engine Combustion Chamber Surfaces SAE Technical Paper 850360 1985 10.4271/850360
- Assanis , D.N. and Heywood , J.B. 1986
- Kamo , R. , Assanis , D.N. , and Bryzik , W. Thin Thermal Barrier Coatings for Engines SAE Transactions 1989 131 136
- Wong , V.W. , Bauer , W. , Kamo , R. , Bryzik , W. et al. Assessment of Thin Thermal Barrier Coatings for IC Engines SAE Transactions 1995 1640 1650
- Mendera , K.Z. Effects of Plasma Sprayed Zirconia Coatings on Diesel Engine Heat Release Journal of KONES 7 1-2 2000 382 389
- Hejwowski , T. and Weroński , A. The Effect of Thermal Barrier Coatings on Diesel Engine Performance Vacuum 65 3-4 2002 427 432
- Tree , D.R. , Wiczynski , P.D. , and Yonushonis , T.M. Experimental Results on the Effect of Piston Surface Roughness and Porosity on Diesel Engine Combustion SAE Transactions 1996 112 121
- Kosaka , H. , Wakisaka , Y. , Nomura , Y. , Hotta , Y. et al. Concept of “Temperature Swing Heat Insulation” in Combustion Chamber Walls, and Appropriate Thermo-Physical Properties for Heat Insulation Coat SAE International Journal of Engines 6 1 2013 142 149
- Wakisaka , Y. , Inayoshi , M. , Fukui , K. , Kosaka , H. et al. Reduction of Heat Loss and Improvement of Thermal Efficiency by Application of “Temperature Swing” Insulation to Direct-Injection Diesel Engines SAE International Journal of Engines 9 3 2016 1449 1459
- Koutsakis , G. and Ghandhi , J. Analytical Solution of Unsteady Heat Conduction in Multilayer Internal Combustion Engine Walls Applied Thermal Engineering 2022
- Koutsakis , G. , Nellis , G.F. , and Ghandhi , J.B. Surface Temperature of a Multi-Layer Thermal Barrier Coated Wall Subject to an Unsteady Heat Flux International Journal of Heat and Mass Transfer 155 2020
- Koutsakis , G. and Ghandhi , J.B. An Analytical Approach for Calculating Instantaneous Multilayer-Coated Wall Surface Temperature in an Engine SAE International Journal of Advances and Current Practices in Mobility 2 2020 1303 1313
- Ghandhi , J. and Koutsakis , G. Comment on “Numerical Approach to Define a Thermodynamically Equivalent Material for the Conjugate Heat Transfer Simulation of Very Thin Coating Layers” by P. Olmeda, X. Margot, P. Quintero, J. Escalona, International Journal of Heat and Mass Transfer, Vol. 162 (2020) 120377 International Journal of Heat and Mass Transfer 173 2021 121190
- Babu , A. , Koutsakis , G. , Kokjohn , S. , and Andrie , M. Experimental and Analytical Study of Temperature Swing Piston Coatings in a Medium-Duty Diesel Engine SAE Technical Paper 2022-01-0442 2022 10.4271/2022-01-0442
- Koutsakis , G. , Miles , S. , and Ghandhi , J. Assessment of In-Cylinder Thermal Barrier Coatings over a Full Vehicle Drive Cycle SAE Technical Paper 2021-01-0456 2021 10.4271/2021-01-0456
- Koutsakis , G. and Ghandhi , J.B. Optimization of Thermal Barrier Coating Performance and Durability over a Drive Cycle International Journal of Engine Research 2022
- Saputo , J.C. , Smith , G.M. , Lee , H. , Sampath , S. et al. Thermal Swing Evaluation of Thermal Barrier Coatings for Diesel Engines Journal of Thermal Spray Technology 2021 1 15
- Chérel , J. , Zaccardi , J.-M. , Bouteiller , B. , and Allimant , A. Experimental Assessment of New Insulation Coatings for Lean Burn Spark-Ignited Engines Oil & Gas Science and Technology-Revue d’IFP Energies Nouvelles 75 2020 11
- Andrie , M. , Kokjohn , S. , Paliwal , S. , Kamo , L.S. et al. Low Heat Capacitance Thermal Barrier Coatings for Internal Combustion Engines SAE Technical Paper 2019-01-0228 1 2019 1 13 10.4271/2019-01-0228
- de Goes , W.U. , Somhorst , J. , Markocsan , N. , Gupta , M. et al. Suspension Plasma-Sprayed Thermal Barrier Coatings for Light-Duty Diesel Engines Journal of Thermal Spray Technology 28 7 1674 1687 2019
- Somhorst , J. , Oevermann , M. , Bovo , M. , and Denbratt , I. Evaluation of Thermal Barrier Coatings and Surface Roughness in a Single-Cylinder Light-Duty Diesel Engine International Journal of Engine Research 2019
- Thibblin , A. , Kianzad , S. , Jonsson , S. , and Olofsson , U. Running-In Behaviour of Thermal Barrier Coatings in the Combustion Chamber of a Diesel Engine Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering 2019
- Uchida , N. A Novel Technology Assessment Chart for Thermal Efficiency Improvement of IC Engines International Journal of Engine Research 2021 14680874211009671
- Koutsakis , G. , Begley , M.R. , Hutchinson , J.W. , and Ghandhi , J.B. Transient Thermo-Mechanical Analysis of Reciprocating Engine Thermal Barrier Coatings Journal of Surface and Coatings Technology 2022
- Gingrich , E. , Tess , M. , Korivi , V. , and Ghandhi , J. High-Output Diesel Engine Heat Transfer: Part 1 - Comparison between Piston Heat Flux and Global Energy Balance International Journal of Engine Research 2021
- Gingrich , E. , Tess , M. , Korivi , V. , Schihl , P. et al. The Impact of Piston Thermal Barrier Coating Roughness on High-Load Diesel Operation International Journal of Engine Research 2019
- Overbye , V.D. , Bennethum , J.E. , Uyehara , O. , and Myers , P. Unsteady Heat Transfer in Engines SAE Transactions 69 1961 461 494
- Chang , J. , G¨uralp , O. , Filipi , Z. , Assanis , D. et al. New Heat Transfer Correlation for an HCCI Engine Derived from Measurements of Instantaneous Surface Heat Flux SAE Transactions 2004 1576 1593
- Gingrich , E. 2020
- Srinivasan , V. , Friis , M. , Vaidya , A. , Streibl , T. et al. Particle Injection in Direct Current Air Plasma Spray: Salient Observations and Optimization Strategies Plasma Chemistry and Plasma Processing 27 5 2007 609 623
- ASTM Standard Test Method for Thermal Diffusivity by the Flash Method 2001
- Nakamura , T. and Liu , Y. Determination of Nonlinear Properties of Thermal Sprayed Ceramic Coatings via Inverse Analysis International Journal of Solids and Structures 44 6 2007 1990 2009
- Liu , Y. , Nakamura , T. , Dwivedi , G. , Valarezo , A. et al. Anelastic Behavior of Plasma-Sprayed Zirconia Coatings Journal of the American Ceramic Society 91 12 2008 4036 4043
- Dwivedi , G. , Nakamura , T. , and Sampath , S. Controlled Introduction of Anelasticity in Plasma-Sprayed Ceramics Journal of the American Ceramic Society 94 2011 s104 s111
- Tan , Y. , Shyam , A. , Choi , W.B. , Lara-Curzio , E. et al. Anisotropic Elastic Properties of Thermal Spray Coatings Determined via Resonant Ultrasound Spectroscopy Acta Materialia 58 16 2010 5305 5315
- Smith , G.M. , Resnick , M. , Kjellman , B. , Wigren , J. et al. Orientation-Dependent Mechanical and Thermal Properties of Plasma-Sprayed Ceramics Journal of the American Ceramic Society 101 6 2018 2471 2481
- Tsui , Y.a.-C. and Clyne , T. An Analytical Model for Predicting Residual Stresses in Progressively Deposited Coatings Part 1: Planar Geometry Thin Solid Films 306 1 1997 23 33
- Matejicek , J. , Sampath , S. , Brand , P. , and Prask , H. Quenching, Thermal and Residual Stress in Plasma Sprayed Deposits: NiCrAlY and YSZ Coatings Acta Materialia 47 2 1999 607 617
- Chandra , L. and Clyne , T. Possible Technique for the Characterization of Diamond Films using an Ultrasonic Resonance Technique Diamond and Related Materials 2 5-7 1993 977 983
- Slim , M.F. , Alhussein , A. , Billard , A. , Sanchette , F. et al. On the Determination of Young’s Modulus of Thin Films with Impulse Excitation Technique Journal of Materials Research 32 3 2017 497 511
- Paul , S. Stiffness of Plasma Sprayed Thermal Barrier Coatings Coatings 7 5 2017 68
- ASTM Standard Test Method for Measurement of Fracture Toughness 2001
- Smith , G.M. , Smith , A. , and Sampath , S. Fracture Toughness of Thermal Spray Ceramics: Measurement Techniques and Processing Dependence Journal of Thermal Spray Technology 27 7 2018 1076 1089
- Donohue , E.M. Investigation of the Parameters Influencing Thermal Barrier Coating Toughness Through a Novel Measurement Technique Santa Barbara 2014
- Hendricks , T.L. 2011
- Sundaram , S. , Lipkin , D. , Johnson , C. , and Hutchinson , J.W. The Influence of Transient Thermal Gradients and Substrate Constraint on Delamination of Thermal Barrier Coatings Journal of Applied Mechanics 80 1 2013