This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Characterization of the Reversal Discharge Coefficient of Intake Port and Direct Discharge Coefficient of Exhaust Port of an Engine Used in Formula SAE Prototype
Technical Paper
2021-36-0107
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Event:
SAE BRASIL 2021 Web Forum
Language:
English
Abstract
In the present work it was studied the flow around the intake and discharge valves of the HONDA CBR 600RR Engine, used in Formula SAE by the team of CEFET-MG, Formula Cefast.
Presenting the methodology and experimental results in the measurement of the reversal discharge coefficient of the intake port and the discharge coefficient of exhaust valve of the engine used in the prototype, serving as a starting point for further studies and development of the prototype drive system. These experimental tests were performed on the flow bench infrastructure of the Pontificia Universidade Católica de Minas Gerais, PUC-MG, using the engine head, same model as used in the Formula Cefast team prototype. Necessary parts and adaptations for tests were developed, such as a mechanism for opening and closing the valves during the experiment. Measurements were taken to define the actual mass flow rate of air through the valves for valve lifts, ranging from 0 mm to 7.3 mm for the exhaust valve and from 0 mm to 8.2 mm for the intake valve. The study was performed by opening only one valve. Increment between valve lift measurements was 0.2 mm and 03 measurements were made for each valve lift. From the measurements of the pressure difference before and after the valves and the air temperature it was possible to determine the theoretical mass flow as a function of the valve lift. The ratio between the actual mass flow rate and the theoretical mass flow rate, characterized the discharge coefficient of the flow. The methodology applied in the experiment was effective with a behavior of discharge coefficients as a function of valve lift comparable with other works and theoretical reviews, ranging from 0.45 to 0.91 for the exhaust valve and ranging from 0.42 to 0.69 for the intake valve.
Authors
- Heitor Augusto Ivo de Oliveira - Centro Federal de Educação Tecnológica de Minas Gerais
- Márcio Expedito Guzzo - Centro Federal de Educação Tecnológica de Minas Gerais
- Fernando Antonio Rodrigues Filho - Centro Federal de Educação Tecnológica de Minas Gerais
- Thiago Augusto Araújo Moreira - Centro Federal de Educação Tecnológica de Minas Gerais
- Jaqueline Mendes Queiroz - Pontifícia Universidade Católica de Minas Gerais
Topic
Citation
de Oliveira, H., Guzzo, M., Filho, F., Moreira, T. et al., "Characterization of the Reversal Discharge Coefficient of Intake Port and Direct Discharge Coefficient of Exhaust Port of an Engine Used in Formula SAE Prototype," SAE Technical Paper 2021-36-0107, 2022, https://doi.org/10.4271/2021-36-0107.Also In
References
- Heywood , John B. Internal Combustion Engine Fundamentals New York McGraw-Hill 1988 205 270 9780070286375
- Semlitsch , B. , Wang , Y. , and Mihâescu , M. Flow Effects Due to Valve and Piston Motion in an Internal Combustion Engine Exhaust Port Energy Conversion and Management , 2015 18 30
- da Costa , R. , Franco , R. , Gomes , C. , Coelho , R. et al. Experimental Methodology and Numerical Simulation of Intake Valves Discharge Coefficients for a Single Cylinder Research Engine SAE Technical Paper 2015-36-0267 2015 https://doi.org/10.4271/2015-36-0267
- Li , Q. , Liu , J. , Fu , J. , Zhou , X. , et al. Comparative Study on the Pumping Losses between Continuous Variable Valve Lift (CVVL) Engine and Variable Valve Timing VVT Engine Applied Thermal Engineering 137 710 720 2018
- Fontana , G. , and Galloni , E. Variable Valve Timing for Fuel Economy Improvement in a Small Spark-Ignition Engine Applied Energy 86 96 105 2009
- Maier , A. , Sheldrake , T., H. , Wilcock , D. Geometric Parameters Influencing Flow in an Axisymmetric IC Engine Inlet Port Assembly: Part I - Valve Flow Characteristics Journal of Fluids Engineering 122 4 650 657 2000
- da Rocha , D. , Guzzo , M. , Gomes Júnior , C. , da Costa , R. et al. Diesel Spray Characterization and Numerical Simulation Using Eulerian-Lagrangian Model SAE Technical Paper 2014-36-0321 2014 https://doi.org/10.4271/2014-36-0321
- Passos Costa , S. , Guzzo , M. , Júnior , C. , Franco , R. et al. Comparative analysis of spray parameters for ethanol and gasoline from a multi-hole direct injector SAE Technical Paper 2018-36-0051 2018 https://doi.org/10.4271/2018-36-0051
- Guzzo , M. , Barros , J. , Júnior , C. , Costa , R. et al. Analysis of ethanol spray behavior into a Single Cylinder Optical Research Engine SAE Technical Paper 2019-36-0223 2020 https://doi.org/10.4271/2019-36-0223
- Guzzo , M. , Filho , F. , Júnior , C. , Costa , S. et al. A Comparative Analysis of Direct Injection into a Pressurized Chamber Using an Automatic Image Treatment Methodology SAE Technical Paper 2016-36-0163 2016 https://doi.org/10.4271/2016-36-0163
- Shudo , T. , and Oba , S. Mixture Distribution Measurement Using Laser Induced Breakdown Spectroscopy in Hydrogen Direct Injection Stratified Charge International Journal of Hydrogen Energy 34 2488 2493 2009
- Algieri , A. Fluid Dynamic Efficiency of a High Performance Multi-Valve Internal Combustion Engine During the Intake Phase - Influence of Valve-Valve Interference Phenomena Thermal Science 17 25 34 2013
- Queiroz , J., M. Influência de um ressonador de volume variável na vazão mássica em um motor de combustão interna 2011
- Çengel , Yunus A. , and Boles , Michael A. Thermodynamics: an Engineering Approach Eighth New York McGraw-Hill 1988 9780073398174