This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Solid Particle Emissions from a Diesel Fuel Based Burner Platform
Technical Paper
2021-01-0627
ISSN: 0148-7191, e-ISSN: 2688-3627
This content contains downloadable datasets
Annotation ability available
Sector:
Event:
SAE WCX Digital Summit
Language:
English
Abstract
Diesel engines are the primary power source for the medium and heavy-duty truck applications in the US. There is a wide range of regulatory developments being considered in the US that would impact the field of diesel engines and aftertreatment systems, such as the California Air Resources Board’s (CARB) low NOX standards and the extended durability requirement for aftertreatment systems. The proposed durability standards would require manufacturers to develop aftertreatment systems targeting up to 800,000 miles of full useful life (FUL) for Heavy heavy-duty (HHD) Application. Robust design and validation of aftertreatment systems is critical to ensure compliance with such stringent regulations. Several methodologies are being considered by the regulatory agencies for the compliance validation process, including the option of accelerated aging of the aftertreatment systems for a portion of the FUL. Performing FUL aging on an engine platform can be both technically challenging and resource intensive. To address these challenges, SwRI has developed a diesel fueled burner platform that could be used for accelerated aging and in-situ performance evaluation of aftertreatment systems for a wide range of engine displacements. Several SAE papers have been published on the burner performance characteristics and controls; however, burner particulate matter physical characteristics had not been addressed.
In this study, burner-out soot mass and solid particle number (PN) emissions along with particle size information were investigated over a range of steady state and transient operating conditions. Burner operation was tuned to achieve soot mass concentration varying from 0.94 mg/m3 to 38 mg/m3, and solid particle number concentration from 9.19e+05 particles/cm3 to 7.81e+07 particle/cm3. The geometric number mean diameter (GNMD) of the corresponding particle size distributions ranged from 14 nm to 58 nm. The physical characteristics of solid particles suggest that the burner-based platform can be used to generate particle emissions representative of compression ignition diesel engines. The development of such a robust burner-based technological solution coupled with detailed understanding of its particle emissions enables this technology to serve as a powerful and cost-effective alternative to engine-based development, validation and aging of next generation diesel exhaust aftertreatment systems.
Recommended Content
Authors
Topic
Citation
Thakral, N., Premnath, V., Khalek, I., Waez, M. et al., "Solid Particle Emissions from a Diesel Fuel Based Burner Platform," SAE Technical Paper 2021-01-0627, 2021, https://doi.org/10.4271/2021-01-0627.Data Sets - Support Documents
Title | Description | Download |
---|---|---|
Unnamed Dataset 1 | ||
Unnamed Dataset 2 | ||
Unnamed Dataset 3 | ||
Unnamed Dataset 4 | ||
Unnamed Dataset 5 | ||
Unnamed Dataset 6 | ||
Unnamed Dataset 7 | ||
Unnamed Dataset 8 | ||
Unnamed Dataset 9 | ||
Unnamed Dataset 10 |
Also In
References
- Buckendale , L.R. , Stanton , D.W. , and Stanton , D.W. 2015
- Puphunwivat , T. Real Driving Emissions - A Game Changer for the Industry?: Mastering On-Road Emissions Targets with Integrated Vehicle Testing Solution AVL M.O.V.E SAE Technical Paper 2015-01-0056 2015 10.4271/2015-01-0056
- EPA Control of Air Pollution From new Motor Vehicles: Heavy-Duty Engine Standards Fed. Regist. 85 13 3306 3330 2020
- Adnani , P. , Lemieux , S. , and Heroy-Rogalski , K. Proposed Durability Demonstration Program for On-Road Heavy- Duty Diesel-Cycle Engines CARB Workshop Proceedings Sacramento California Air Resources Board 2019
- Zavala , B. , Vats , S. , and Eakle , S. The Diesel Aftertreatment Accelerated Aging Cycle Protocol: An Advanced Aftertreatment Case Study SAE Technical Paper 2020-01-2210 1-11 2020 2020 10.4271/2020-01-2210
- Workshop , C. Examples of Heavy-Duty Diesel and Off-Road Diesel Engine Deterioration Factor Validation for CARB and US EPA Approval 2020
- Watson , S.A.G. , Huang , W. , and Wong , V.W. Correlations Among Ash-Related Oil Species in the Power Cylinder, Crankcase and the Exhaust Stream of a Heavy-Duty Diesel Engine SAE Technical Paper 2007-01-1965 2007 10.4271/2007-01-1965
- Sappok , A. , Wang , Y. , Wang , R.Q. , Kamp , C. , and Wong , V. Theoretical and Experimental Analysis of Ash Accumulation and Mobility in Ceramic Exhaust Particulate Filters and Potential for Improved Ash Management SAE Int. J. Fuels Lubr. 7 2 511 524 2014 10.4271/2014-01-1517
- Dittler , A. Ash Transport in Diesel Particle Filters SAE Techncial Paper 2012-01-1732 9 2012 10.4271/2012-01-1732
- Matsuno , M. , and Kitamura , T. Direct Visualization of Soot and Ash Transport in Diesel Particulate Filters During Active Regeneration Process SAE Technical Paper 2019-01-2287 Dec. 2019 10.4271/2019-01-2287
- Thakral , N. , Premnath , V. , Khalek , I. , and Eakle , S. Development of a Burner-Based Test System to Produce Controllable Particulate Emissions for Evaluation of Gasoline Particulate Filters SAE Technical Paper 2020-01-0389 2020 10.4271/2020-01-0389.
- Schindler , W. , Haisch , C. , Beck , H.A. , Niessner , R. , Jacob , E. , and Rothe , D. A Photoacoustic Sensor System for Time Resolved Quantification of Diesel Soot Emissions 2004 724 2004
- Reavell , K. , Hands , T. , and Collings , N. A Fast Response Particulate Spectrometer 2002
- Khalek , I.A. Sampling System for Solid and Volatile Exhaust Particle Size , Number , and Mass Emissions 2007 2007
- Premnath , V. , Khalek , I. , Thompson , P. , and Woo , L. Evaluation of an On-Board, Real-Time Electronic Particulate Matter Sensor Using Heavy-Duty On-Highway Diesel Engine Platform SAE Technical Paper 2020-01-0385 2020 10.4271/2020-01-0385
- Rissler , J. , Messing , M.E. , Malik , A.I. , Nilsson , P.T. et al. Effective Density Characterization of Soot Agglomerates from Various Sources and Comparison to Aggregation Theory Effective Density Characterization of Soot Agglomerates from Various Sources and Comparison to Aggregation Theory 6826 2013 10.1080/02786826.2013.791381.
- Kumar , D. , Agarwal , A.K. , and Gupta , T. Effect of Engine Load on Size and Number Distribution of Particulate Matter Emitted From a Direct Injection Compression Ignition Engine Aerosol Air Qual. Res. 11 7 915 920 2011 10.4209/aaqr.2011.05.0070.
- Fiebig , M. , Wiartalla , A. , Holderbaum , B. , and Kiesow , S. Particulate Emissions from Diesel Engines: Correlation Between Engine Technology and Emissions J. Occup. Med. Toxicol. 9 1 1 18 2014 10.1186/1745-6673-9-6.
- Khalek , I.A. , Bougher , T.L. , Merritt , P.M. , and Zielinska , B. Regulated and Unregulated Emissions from Highway Heavy-Duty Diesel Engines Complying with U.S. Environmental Protection Agency 2007 Emissions Standards J. Air Waste Manag. Assoc. 61 4 427 442 2011 10.3155/1047-3289.61.4.427
- K , A.P. , Bernemyr , H. , and Erlandsson , A. On the Effects of Turbocharger on Particle Number and Size Distribution in a Heavy - Duty Diesel Engine SAE Technical Paper 2020-24-0007 1 2020 10.4271/2020-24-0007.
- Khalek , I.A. , Blanks , M.G. , Merritt , P.M. , and Zielinska , B. Regulated and Unregulated Emissions From Modern 2010 Emissions-Compliant Heavy-Duty On-Highway Diesel Engines J. Air Waste Manag. Assoc. 65 8 987 1001 2015 10.1080/10962247.2015.1051606
- Duvvuri , P.P. , Sukumaran , S. , Shrivastava , R.K. , and Sreedhara , S. Modeling the Effect of Parametric Variations on Soot Particle Size Distribution in a Diesel Engine J. Energy Resour. Technol. 142 3 1 7 2020 10.1115/1.4044563