This content is not included in your SAE MOBILUS subscription, or you are not logged in.
Calibration Procedure for Measurement-Based Fast Running Model for Hardware-in-the-Loop Powertrain Systems
ISSN: 0148-7191, e-ISSN: 2688-3627
Published April 14, 2020 by SAE International in United States
This content contains downloadable datasetsAnnotation ability available
The requirements set for the next-generation powertrain systems (e.g. performance and emissions) are becoming increasingly stringent with ever-shortening time-to-markets at reduced costs. To remain competitive automotive companies are progressively relying on model-driven development and virtual testing. Virtual test benches, such as HiL (Hardware-in the-Loop) simulators, are powerful tools to reduce the amount of physical testing and speed up engine software calibration process. The introduction of these technologies places new, often conflicting demands (such as higher predictability, faster simulation speed, and reduced calibration effort) upon simulation models used at HiL test benches. The new models are also expected to offer compliance to industry standards, performance and usability to further increase the usage of virtual tests in powertrain development. This paper presents the methodology for creating and calibrating a computational model of a heavy-duty diesel engine suitable for HiL simulations. The novelty of the study is two-fold: it relies solely on engine dynamometer test data (does not use manufacturers’ inputs) and it employs a generic builder in GT-SUITE simulation software to create a baseline real-time model for calibration (does not rely on a detailed simulation model). The obtained results for engine performance and exhaust emissions provide favorable results for both steady-state and transient operating conditions. The developed model is successfully employed at the VIRTEC (VIRtual Test Cell) system at Volvo Penta for the purpose of validation and optimization of engine control strategies.
CitationAndric, J., Schimmel, D., and Heide, J., "Calibration Procedure for Measurement-Based Fast Running Model for Hardware-in-the-Loop Powertrain Systems," SAE Technical Paper 2020-01-0254, 2020, https://doi.org/10.4271/2020-01-0254.
Data Sets - Support Documents
|Unnamed Dataset 1|
- Gehring , J. and Schütte , H. A Hardware-in-the-Loop Test Bench for the Validation of Complex ECU Networks SAE Technical Paper 2002-01-0801 2002 https://doi.org/10.4271/2002-01-0801
- Ruggiero , A. , Montalto , I. , Poletto , P. Pautasso , E. , Mustafaj , K. , and Servetto , E. Development and Assessment of a Fully-Physical 0D Fast Running Model of an E6 Passenger Car Diesel Engine for ECU Testing on a Hardware-in-the-Loop System International Conference SIA Powertrain, Rouen 2014
- Barasa , P. , Tian , Y. , Hardes , S. , Owlia , S. et al. Virtual Engine, Controls, and Calibration Development in Automated Co-Simulation Environment SAE Technical Paper 2016-01-0090 2016 https://doi.org/10.4271/2016-01-0090
- Andric , J. , Schimmel , D. Sediako , A.D. , Sjöblom , J. , and Faghani , E. Development and Calibration of One-Dimensional Engine Model for Hardware-in-the-Loop Applications SAE Technical Paper 2018-01-0874 2018 https://doi.org/10.4271/2018-01-0874
- Pfau , R.U. and Schaden , T. Real-Time Simulation of Extended Vehicle Drivetrain Dynamics Multibody Dynamics Computational Methods in Applied Sciences 23 195 214 2011
- Gamma Technologies GT-Power User’s Manual Version 2019
- Nguyen-Schäfer , H. Rotordynamics of Automotive Turbochargers: Linear and NonlinearRotordynamics-Bearing Design -Rotor Balancing Springer-Verlag 2012