This content is not included in your SAE MOBILUS subscription, or you are not logged in.
Investigate Partial Cabin Air Recirculation Strategy to Improve HVAC System’s Heating Performance Using 1D Simulation
ISSN: 0148-7191, e-ISSN: 2688-3627
Published April 14, 2020 by SAE International in United States
This content contains downloadable datasetsAnnotation ability available
In cold weather conditions, cabin heating performance is critical for retaining the thermal comfort. Heat is absorbed from the engine by circulating coolant through the engine water jacket and same will be rejected by the heater core. A variable speed blower is used to transfer heat from the heater core to the passenger compartment through floor ducts. The time taken to achieve comfortable cabin temperature determines the performance and capacity of heating ventilating and air conditioning (HVAC) system. In current automotive field, the engine options are provided to customers to meet their needs on the same vehicle platforms. Hence few engine variants cannot warm the cabin up to customer satisfaction. To improve the existing warm up performance of system, Positive thermal coefficient heater (PTC), electric coolant PTC heater, auxiliary pump etc. can be used which increases the overall cost of the vehicle.
During warmup, HVAC system operates in 100% fresh mode. In this study, Partial cabin recirculation is investigated to understand the effect on the cabin warmup. In order to demonstrate this phenomenon, a one dimensional (1D) modelling approach is used for simulation and predicted the performance of different percentage of partial cabin air recirculation. Baseline correlation simulation is done with vehicle test data to reproduce the same test conditions in 1D software. Model output parameters such as floor duct outlet air temperature, Cabin warmup temperature are correlated at 0% partial recirculation in other words 100% fresh mode. By increasing the partial recirculation at each simulation run, increase in the floor duct outlet air temperatures is observed and witnessed through 1D model. This strategy can be applied to upcoming vehicle to improve the cabin warmup performance without any additional cost.
CitationBelsare, S., Danapalan, P., Sambandan, S., and Govindarajalu, M., "Investigate Partial Cabin Air Recirculation Strategy to Improve HVAC System’s Heating Performance Using 1D Simulation," SAE Technical Paper 2020-01-0159, 2020, https://doi.org/10.4271/2020-01-0159.
Data Sets - Support Documents
|[Unnamed Dataset 1]|
- Sambandan, S., Valencia, M., and Sathish Kumar, S. , “Robust 1D Modelling for Automotive HVAC Warmup Prediction Using DFSS Approach,” SAE Technical Paper 2017-01-0179, 2017, https://doi.org/10.4271/2017-01-0179.
- Vasanth, B. , “HVAC Defrost System Assessment through 1D and 3D Simulation during Concept Development,” SAE Technical Paper 2019-01-0911, 2019, https://doi.org/10.4271/2019-01-0911.
- Grady, M., Jung, H., Kim, Y., and Park, J. , “Vehicle Cabin Air Quality with Fractional Air Recirculation,” SAE Technical Paper 2013-01-1494, 2013, https://doi.org/10.4271/2013-01-1494.
- Galatsis, K. , Car Cabin Air Quality Sensors and Systems (American Scientific Publishers, 2006), 1-58883-056-X.
- Matton, T.J.P. , “Simulation and Analysis of Air Recirculation Control Strategies to Control Carbon Dioxide Build-Up inside a Vehicle Cabin,” Electronic theses and dissertations, 2015, Paper 5269.
- Atkinson, W., Hill, W., and Mathur, G. , “The Impact of Increased Air Recirculation on Interior Cabin Air Quality,” SAE Technical Paper 2017-01-0169, 2017, https://doi.org/10.4271/2017-01-0169.
- Filho, A. , “New Vehicles Cabin Indoor Air Quality,” SAE Technical Paper 2010-36-0390, 2010, https://doi.org/10.4271/2010-36-0390.
- ASHRAE , “Standard 62-2001, Ventilation for Acceptable Indoor Air Quality,” American Society of Heating, Refrigerating, and Air-Conditioning Engineers, Atlanta, GA, www.ASHRAE.org, 2001.
- Walter, F.B. , Medical Physiology: A Cellular and Molecular Approach (Elsevier/Saunders, 2005), 829. ISBN:1-4160-2328-3.