This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
A Development of Measurement System for Piston Ring Sliding Surface Pressure
Technical Paper
2018-32-0022
ISSN: 0148-7191, e-ISSN: 2688-3627
This content contains downloadable datasets
Annotation ability available
Sector:
Language:
English
Abstract
The piston rings, the engine sliding parts, are required to further contribute on mechanical loss reduction in order to improve fuel efficiency. However, many cases of the abnormal combustion due to oil upward flow, as well as the increase in oil consumption have been reported. Therefore, elucidation of the mechanism of those phenomena is still an urgent task. It is widely known that the distribution of the sliding face pressure in between the piston ring and the cylinder bore largely influence the oil flow via the sliding face of the piston ring. However, there are many unknown aspects in this field. Therefore, verification of the sliding face pressure during the actual operation is necessary in order to elucidate the mechanism of oil consumption. The thin-film sensor, since it has little influence on shape, is widely used as a measurement method of the sliding face pressure between two different faces, however this method has never been applied to the piston ring in the past. Authors, through the examination of various film deposition methods, succeeded in forming the thin-film sensor with a total thickness of 4-5μm by the sputtering method on the sliding face of the piston ring. In addition, with regard to each device composing the measurement system, improvements are applied to obtain better S/N ratio, which enabled the establishment of the measurement system with extended measurable area towards lower pressure region. Furthermore, authors succeeded in measuring the piston ring sliding face pressure through the examination using the rig test device.
Recommended Content
Authors
Topic
Citation
Mochizuki, K., Watanabe, Y., Owashi, M., and Mihara, Y., "A Development of Measurement System for Piston Ring Sliding Surface Pressure," SAE Technical Paper 2018-32-0022, 2018, https://doi.org/10.4271/2018-32-0022.Data Sets - Support Documents
Title | Description | Download |
---|---|---|
Unnamed Dataset 1 | ||
Unnamed Dataset 2 | ||
Unnamed Dataset 3 |
Also In
References
- Usui , M. et al. 2016
- Urabe , M. et al. 2015
- Iijima , A et al. 2012
- Tanaka , J. et al. 2015
- Furuhama , S. et al. A Study of the Oil Loss through the Piston Journal of JSME (3) 28 193 1212 1223 1962
- Hitosugi , H. et al. Study on Reduction of Lubricating Oil Consumption Caused by Cylinder Bore Deformation Journal of Internal Combustion Engine Symposium 211 216 1996
- Saitoh , S. et al. Effect of Cylinder Bore Deformation and Piston Ring Tension on SI Engine Oil Consumption Journal of JSAE 43 3 661 666 2012
- Brown , S.R. et al. Negative Pressure under a Lubricated Piston Ring Journal of Mechanical Engineering Science 20 1 49 57 1978
- Seungchul , K. et al. A Study on the Dynamic Behavior of Oil Film between Piston Ring and Cylinder Liner (2nd Report), The Measurement of oil Film Pressure Using Simulating Rig Journal of JSME (C) 60 578 260 266 1994
- Cheng , C. et al. Three-Dimensional the Piston Ring-Cylinder Bore Contact Modeling Trans. of the ASME, Journal of Engineering for Gas Turbines and Power 137 11 2015
- Hitosugi , H. et al. A Study of Piston Ring Reducing High Contact Pressure at Ring End Gap in Engine Operation Journal of JSAE 32 4 163 168 2001
- Sasaki , R. et al. Numerical Analysis of Oil Behavior around Piston Ring for Liquid-Gas Two-Phase Flow Simulation Journal of Internal Combustion Engine Symposium 2016
- Yamamoto , K. et al. Dynamic Contact Analysis of Piston Ring in Distorted Cylinder Bore Journal of Internal Combustion Engine Symposium 2016
- Bregar , J. et al. Fuel Transport across the Piston Ring Pack : Development of a Computationally Efficient Simulation Model SAE Technical Paper 2015-24-2534 2015 10.4271/2015-24-2534
- Baelden , C. 2014
- Someya , T. et al. Pressure Measurement in Engine Bearing by a New Thin-Film Sensor VAREHD 12 Suceava 8-9, Oct. 2004
- Owashi , M. et al. Development of a Measurement Method of Contact Pressure between Gear Teeth Using a Thin-Film Sensor (Measurement of Pressure Distribution by Multi-Point Pressure Sensor with Shared Lead Films) Journal of JSME (C) 77 782 396 408 2011
- Miura , K. et al. High Durability Thin-Film Pressure Sensor Development for Engine Sliding Surface The 9th International conference on Modeling and Diagnostics for Advanced Engine Systems Comodia 2017
- Kamiya , M. et al. Measurement of Piston Skirt Oil-Film Pressure under Piston Slap SAE Technical Paper 2007-01-2215 2007 10.4271/2007-01-2215
- The Handbook for Mechanical Engineering - Materials Mechanics JSME 1984
- 1997
- Watanabe , S. 1968