This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Simulation of the Effect of Intake Pressure and Split Injection on Lean Combustion Characteristics of a Poppet-Valve Two-Stroke Direct Injection Gasoline Engine at High Loads
Technical Paper
2018-01-1723
ISSN: 0148-7191, e-ISSN: 2688-3627
This content contains downloadable datasets
Annotation ability available
Sector:
Language:
English
Abstract
Poppet-valve two-stroke gasoline engines can increase the specific power of their four-stroke counterparts with the same displacement and hence decrease fuel consumption. However, knock may occur at high loads. Therefore, the combustion with stratified lean mixture was proposed to decrease knock tendency and improve combustion stability in a poppet-valve two-stroke direct injection gasoline engine. The effect of intake pressure and split injection on fuel distribution, combustion and knock intensity in lean mixture conditions at high loads was simulated with a three-dimensional computational fluid dynamic software. Simulation results show that with the increase of intake pressure, the average fuel-air equivalent ratio in the cylinder decreases when the second injection ratio was fixed at 70% at a given amount of fuel in a cycle. With the increase of intake pressure, ignition timing advances, combustion duration slightly decreases first and then increases while the maximum pressure rise rate first increases and then drops. High intake pressure can prevent the occurrence of knock through decreased fuel-air equivalent ratio around the cylinder. The second injection timing can also influence combustion processes. The improved indicated thermal efficiency occurs when the second injection timing is 90°CA after top dead center. Delayed second injection timing is beneficial for the development of initial flame kernel. But when the second injection timing is 60°CA after top dead center, the fuel is only consumed by flame propagation. When auto-ignition occurs in the end mixture, the heat released by auto-ignition gradually increases with the delay of the second injection timing. Meanwhile, indicated thermal efficiency is increased when little amount of end mixture auto-ignites without knock.
Authors
Topic
Citation
Li, X., He, B., Zhao, H., Zhang, Y. et al., "Simulation of the Effect of Intake Pressure and Split Injection on Lean Combustion Characteristics of a Poppet-Valve Two-Stroke Direct Injection Gasoline Engine at High Loads," SAE Technical Paper 2018-01-1723, 2018, https://doi.org/10.4271/2018-01-1723.Data Sets - Support Documents
Title | Description | Download |
---|---|---|
Unnamed Dataset 1 | ||
Unnamed Dataset 2 |
Also In
References
- Mock P. 2 2014
- Mock P. 2 2016
- Osborne , R. , Stokes , J. , Lake , T. , Carden , P. et al. Development of a Two-Stroke/Four-Stroke Switching Gasoline Engine - The 2/4SIGHT Concept SAE Technical Paper 2005-01-1137 2005 10.4271/2005-01-1137
- Yang , X. , Okajima , A. , Takamoto , Y. , and Obokata , T. Numerical Study of Scavenging Flow in Poppet-Valved Two-Stroke Engines SAE Technical Paper 1999-01-1250 1999 10.4271/1999-01-1250
- Nomura , K. and Nakamura , N. Development of a New Two-Stroke Engine with Poppet-Valves: Toyota S-2 Engine A New Generation of Two-Stroke Engines for the Future 1993 53 62
- Turner , J. , Blundell , D. , Pearson , R. , Patel , R. et al. Project Omnivore: A Variable Compression Ratio ATAC 2-Stroke Engine for Ultra-Wide-Range HCCI Operation on a Variety of Fuels SAE Int. J. Engines 3 1 938 955 2010 10.4271/2010-01-1249
- Blundell , D. , Turner , J. , Duret , P. , Lavy , J. et al. Design and Evaluation of the ELEVATE Two-stroke Automotive Engine SAE Technical Paper 2003-01-0403 2003 10.4271/2003-01-0403
- Li , Z. , He , B. , and Zhao , H. The Influence of Intake Port and Pent-Roof Structures on Reversed Tumble Generation of a Poppet-Valved Two-Stroke Gasoline Engine SAE Technical Paper 2014-01-1130 2014 10.4271/2014-01-1130
- Howell , T. , Swanbon , B. , Baltrucki , J. , Steines , A. et al. Vehicle Demonstration of 2 Stroke Engine Brake in a Heavy Duty Truck SAE Int. J. Commer. Veh. 9 2 260 269 2016 10.4271/2016-01-8061
- Nakano , M. , Sato , K. , and Ukawa , H. A Two-Stroke Cycle Gasoline Engine with Poppet Valves on the Cylinder Head SAE Technical Paper 901664 1990 10.4271/901664
- Hundleby , G. Development of a Poppet-Valved Two-Stroke Engine - The Flagship Concept SAE Technical Paper 900802 1990 10.4271/900802
- Dalla , N. and Zhao , H. High Load Performance and Combustion Analysis of a Four-Valve Direct Injection Gasoline Engine Running in the Two-Stroke Cycle Applied Energy 159 117 131 2015 10.1016/j.apenergy.2015.08.122
- Garg , M. , Kumar , D. , Syed , M. , and Nageswara , S. CFD Modelling of a Two Stroke Engine to Predict and Reduce Short Circuit Losses SAE Int. J. Engines 9 1 355 364 2016
- Zhang , Y. and Zhao , H. Investigation of Combustion, Performance and Emission Characteristics of 2-Stroke and 4-Stroke Spark Ignition and CAI/HCCI Operations in a DI Gasoline Applied Energy 130 244 255 2014 10.1016/j.apenergy.2014.05.036
- Zhang , Y. and Zhao , H. Optimisation of Boosting Strategy for Controlled Auto-Ignition Combustion in a Four-Valve Camless Gasoline Direct Injection Engine Running in Two-Stroke Cycle Int. J. Engine Res. 15 7 850 861 2014 10.1177/1468087413519991
- Marseglia , G. , Costa , M. , Catapano , F. , Sementa , P. et al. Study about the Link between Injection Strategy and Knock Onset in an Optically Accessible Multi-Cylinder GDI Engine Energy Convers. Manag. 134 1 19 2017 10.1016/j.enconman.2016.12.012
- Zhao , H. Advanced Direct Injection Combustion Engine Technologies and Development Florida CRC Press 2010
- Smith , J. , Szekely Jr , G. , Solomon , A. , and Parrish , S. A Comparison of Spray-Guided Stratified-Charge Combustion Performance with Outwardly-Opening Piezo and Multi-Hole Solenoid Injectors SAE Int. J. Engines 4 1 1481 1497 2011 10.4271/2011-01-1217
- Drake , M.C. and Haworth , D.C. Advanced Gasoline Engine Development Using Optical Diagnostics and Numerical Modeling Proceedings of the Combustion Institute 31 1 99 124 2007 10.1016/j.proci.2006.08.120
- Migliaccio , M. , Montanaro , A. , Beatrice , C. et al. Experimental and Numerical Analysis of a High-Pressure Outwardly Opening Hollow Cone Spray Injector for Automotive Engines Fuel 196 508 519 2017 10.1016/j.fuel.2017.01.020
- Schmid , A. , Schneider , B. , Boulouchos , K. et al. Experimental Investigations on a Piezo Activated Hollow Cone Injector-Part I: Measurement of Needle Lift and Its Influence on Spray Morphology Atomization & Sprays 24 10 841 857 2014 10.1615/AtomizSpr.2014007329
- Araneo , L. and Donde , R. Flash Boiling in a Multihole GDI Injector-Effects of the Fuel Distillation Curve Fuel 191 500 510 2017 10.1016/j.fuel.2016.11.104
- He , B. and Ye , F. Spray Characteristics of an Outward-Opening Gasoline Piezoelectric Injector Trans. Chinese Soc. Agric. Mach. 46 6 275 281 2015 https://10.6041/j.issn.1000-1298.2015.06.040
- Zhao , F. , Lai , M.C. , and Harrington , D.L. Automotive Spark-Ignited Direct-Injection Gasoline Engines Progress in Energy and Combustion Science 25 5 437 562 1999 10.1016/S0360-1285(99)00004-0
- Chevillard , S. , Colin , O. , Bohbot , J. , Wang , M. et al. Advanced Methodology to Investigate Knock for Downsized Gasoline Direct Injection Engine Using 3D RANS Simulations SAE Technical Paper 2017-01-0579 2017 10.4271/2017-01-0579
- Mubarak Ali , M. , Hernandez Perez , F. , Vedharaj , S. , Vallinayagam , R. et al. Effect of Timing and Location of Hotspot on Super Knock during Pre-Ignition SAE Technical Paper 2017-01-0686 2017 10.4271/2017-01-0686
- Merola , S.S. et al. Effect of the Fuel-Injection Strategy on Flame-Front Evolution in an Optical Wall-Guided DISI Engine with Gasoline and Butanol Fueling J. Energy Engine 142 2 E4015004 2016 10.1061/(ASCE)EY.1943-7897.0000301
- Wei , H. , Shao , A. , Hua , J. , Zhou , L. et al. Effects of Applying a Miller Cycle with Split Injection on Engine Performance and Knock Resistance in a Downsized Gasoline Engine Fuel 214 98 107 2018 10.1016/j.fuel.2017.11.006
- Li , J. , Ling , X. , Liu , D. , Yang , W. et al. Numerical Study on Double Injection Techniques in a Gasoline and Biodiesel Fueled RCCI (Reactivity Controlled Compression Ignition) Engine Applied Energy 211 382 392 2018 10.1016/j.apenergy.2017.11.062
- Richards , K.J. , Senecal , et al. 2016
- Cung , K. , Moiz , A. , Johnson , J. , Lee , Y. et al. Spray-Combustion Interaction Mechanism of Multiple-Injection under Diesel Engine Conditions Proc. Combust. Inst. 35 3 3061 3068 2015 10.1016/j.proci.2014.07.054
- Han , Z. and Reitz , R. Turbulence Modeling of Internal Combustion Engines Using RNG κ-ε Models Combust. Science Tech. 106 4-6 267 295 1995 10.1080/00102209508907782
- Amsden , A. , Orourke , P. , and Butler , T. 1989 89
- Reitz , R. and Bracco , F. Mechanisms of Breakup of Round Liquid Jets Encyclo. Fluid Mech. 3 233 249 1986
- Xin , J. , Ricart , L. , and Reitz , R. Computer Modeling of Diesel Spray Atomization and Combustion Combust. Science Tech. 137 1-6 171 194 1998 10.1080/00102209808952050
- Reitz , R. and Diwakar , R. Structure of High-Pressure Fuel Sprays SAE Technical Paper 870598 1987 10.4271/870598
- Schmidt , D. and Rutland , C. A New Droplet Collision Algorithm J. Comput. Phys. 164 1 62 80 2000 10.1006/jcph.2000.6568
- Gonzalez , D.M. , Lian , Z. , and Reitz , R. Modeling Diesel Engine Spray Vaporization and Combustion SAE Technical Paper 920579 1992 10.4271/920579
- Bai , C. and Gosman , A. Development of Methodology for Spray Impingement Simulation SAE Technical Paper 950283 1995 10.4271/950283
- Tan , Z. and Reitz , R. Development of a Universal Turbulent Combustion Model for Premixed and Direct Injection Spark/Compression Ignition Engines SAE Technical Paper 2004-01-0102 2004 10.4271/2004-01-0102
- Liang , L. , Reitz , R. , Iyer , C. , and Yi , J. Modeling Knock in Spark-Ignition Engines Using a G-equation Combustion Model Incorporating Detailed Chemical Kinetics SAE Technical Paper 2007-01-0165 2007 10.4271/2007-01-0165
- Liu , Y. , Jia , M. , Xie , M. et al. Enhancement on a Skeletal Kinetic Model for Primary Reference Fuel Oxidation by Using a Semi Decoupling Methodology Energy Fuels 26 12 7069 7083 2012 https://pubs.acs.org/doi/10.1021/ef301242b
- Senecal , P. , Pomraning , E. , Richards , K. , Briggs , T. et al. Multi-Dimensional Modeling of Direct-Injection Diesel Spray Liquid Length and Flame Lift-off Length using CFD and Parallel Detailed Chemistry SAE Technical Paper 2003-01-1043 2003 10.4271/2003-01-1043
- Ewald , J. and Peters , N. A Level Set Based Flamelet Model for the Prediction of Combustion in Spark Ignition Engines 15th International Multidimensional Engine Modeling User’s Group Meeting Detroit 2005
- Yang , X. , Solomon , A. , and Kuo , T. Ignition and Combustion Simulations of Spray-Guided SIDI Engine using Arrhenius Combustion with Spark-Energy Deposition Model SAE Technical Paper 2012-01-0147 2012 10.4271/2012-01-0147
- Fu , X. , He , B. , and Zhao , H. The Upper-Load Extension of a Boosted Direct Injection Poppet Valve Two-Stroke Gasoline Engine SAE Technical Paper 2016-01-2339 2016 10.4271/2016-01-2339
- Dahms , R. , Fansler , T. , Drake , M. et al. Modeling Ignition Phenomena in Spray-Guided Spark-Ignited Engines Proc. Combust. Inst. 32 2 2743 2750 2009 10.1016/j.proci.2008.05.052
- Singh , S. , Reitz , R. , Wickman , D. , Stanton , D. et al. Development of a Hybrid, Auto-Ignition/Flame-Propagation Model and Validation Against Engine Experiments and Flame Liftoff SAE Technical Paper 2007-01-0171 2007 10.4271/2007-01-0171
- Martz , J. , Kwak , H. , Im , H. et al. Combustion Regime of a Reacting Front Propagating into an Auto-Igniting Mixture Proc. Combust. Inst. 33 2 3001 3006 2011 10.1016/j.proci.2010.07.040
- He , B. and Lin , C. Numerical Study of the Effect of Injection Strategies on SFI Hybrid Combustion Process on a Poppet-Valve Two-Stroke DI Gasoline Engine Trans. CSICE 05 406 414 2017 https://10.16236/j.cnki.nrjxb.201705057
- Wang , X. , Zhao , H. , and Xie , H. Effect of Dilution Strategies and Direct Injection Ratios on Stratified Flame Ignition (SFI) Hybrid Combustion in a PFI/DI Gasoline Engine Appl. Energy 165 801 814 2016 10.1016/j.apenergy.2015.12.116
- Mehl , M. , Pitz , W. , Westbrook , C. , Yasunaga , K. et al. Autoignition Behavior of Unsaturated Hydrocarbons in the Low and High Temperature Regions Proc. Combust. Inst. 33 1 201 208 2011 10.1016/j.proci.2010.05.040
- Park , S. and Furukawa , T. Validation of Turbulent Combustion and Knocking Simulation in Spark-Ignition Engines Using Reduced Chemical Kinetics SAE Technical Paper 2015-01-0750 2015 10.4271/2015-01-0750