This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Experimental Analysis on the ‘Exact’ Cremer Impedance in Rectangular Ducts
Technical Paper
2018-01-1523
ISSN: 0148-7191, e-ISSN: 2688-3627
This content contains downloadable datasets
Annotation ability available
Sector:
Language:
English
Abstract
Cremer impedance, first proposed by Cremer (Acustica 3, 1953) and then improved by Tester (JSV 28, 1973), refers to the locally reacting boundary condition that can maximize the attenuation of a certain acoustic mode in a uniform waveguide. One limitation in Tester’s work is that it simplified the analysis on the effect of flow by only considering high frequencies or the ‘well cut-on’ modes. This approximation is reasonable for large duct applications, e.g., aero-engines, but not for many other cases of interest, with the vehicle intake and exhaust system included. A recent modification done by Kabral et al. (Acta Acustica united with Acustica 102, 2016) has removed this limitation and investigated the ‘exact’ solution of Cremer impedance for circular waveguides, which reveals an appreciable difference between the exact and classic solution in the low frequency range. Consequently, the exact solution can lead to a much higher low-frequency attenuation level. In addition, the exact solution is found to exhibit some special properties at very low frequencies, e.g., a negative resistance. In this paper, liners designed on the basis of the exact solution are tested and the difference between the exact and classic solution in the low frequency range (not low enough to go into the negative resistance region) is experimentally investigated.
Authors
Citation
Zhang, Z., Tiikoja, H., Peerlings, L., and Abom, M., "Experimental Analysis on the ‘Exact’ Cremer Impedance in Rectangular Ducts," SAE Technical Paper 2018-01-1523, 2018, https://doi.org/10.4271/2018-01-1523.Data Sets - Support Documents
Title | Description | Download |
---|---|---|
Unnamed Dataset 1 | ||
Unnamed Dataset 2 | ||
Unnamed Dataset 3 |
Also In
References
- Cremer , L Theory Regarding the Attenuation of Sound Transmitted by Air in a Rectangular Duct with an Absorbing Wall, and the Maximum Attenuation Constant Produced during This Process Acustica 3 249 263 1953
- Tester , B. J. The Optimization of Modal Sound Attenuation in Ducts, in Absence of Mean Flow J. Sound Vib 27 477 1973
- Tester , B.J. The Propagation and Attenuation of Sound in Lined Ducts Containing Uniform or “Plug” Flow J. Sound Vib. 28 151 203 1973
- Kabral , R. , Du , L. , Åbom , M. , and Knutsson , M. A Compact Silencer for the Control of Compressor Noise SAE Int. J. Engines. 7 1572 1578 2014 10.4271/2014-01-2060
- Kabral , R. , Du , L. , and Åbom , M. Optimum Sound Attenuation in Flow Ducts Based on the “Exact” Cremer Impedance Acta Acust. United with Acust. 102 851 860 2016
- Zhang , Z. , Kabral , R. , Nilsson , B. , and Åbom , M. Revisiting the Cremer Impedance Proc. Mtgs. Acoust. 30 2017 040009 10.1121/2.0000619
- Eversman , W. Computation of Axial and Transverse Wave Numbers for Uniform Two-Dimensional Ducts with Flow Using a Numerical Integration Scheme J. Sound Vib. 41 252 255 1975
- Maa , D. Y. Potential of microperforated panel absorber The Journal of Acoustical Society of America 104 5 2861 2866 1998
- Allam , S Numerical Assessment and Shape Optimization of Dissipative Muffler and Its Effect on I.C. Engine Acoustic Performance American Journal of Vehicle Design 2 1 22 31 2014
- Temiz , M.A. , Arteaga , I.L. , Efraimsson , G. , Åbom , M. , and Hirschberg , A. The Influence of Edge Geometry on End-correction Coefficients in Microperforated Plates The Journal of the Acoustical Society of America 138 6 3668 3677 2015
- A. B. Comsol www.comsol.se
- Åbom , M. Measurement of the Scattering-matrix of Acoustical Two-ports Mechanical Systems and Signal Processing 5 2 89 104 1991
- Jing , X. D. , Peng , S. , Sun X. F. A Straightforward Method for Wall Impedance Eduction in a Flow Duct J. Acoust. Soc. Am. 124 1 227 234 2008
- Zhou , L. Comparison of Impedance Eduction Results Using Different Methods and Test Rigs 20th AIAA/CEAS Aeroacoustics Conference 2014