This content is not included in your SAE MOBILUS subscription, or you are not logged in.
Realizing Stoichiometric, Natural Gas-Fueled Combustion in Diesel Engines
ISSN: 0148-7191, e-ISSN: 2688-3627
Published April 03, 2018 by SAE International in United States
Annotation ability available
For high-load applications, natural gas represents a clean burning, readily available, and relatively inexpensive alternative to number 2 Diesel fuel. However, the fuel’s poor ignitability has previously limited implementation to spark ignited and dual-fueled engines. These approaches suffer from reduced peak load and high engine-out particulate emissions, respectively, requiring lean operation and expensive aftertreatment to meet regulatory standards. A high-temperature combustion strategy can overcome the difficult ignitibility, allowing for true Diesel-style combustion of pure methane-the least ignitable and least sooting component of natural gas. In order to achieve this result, a compression system was designed to supply fuel at pressures suitably high to achieve good mixing and short injection durations, and a solenoid-actuated Diesel fuel injector was modified to function at these pressures with a gaseous fuel. This fuel supply system was paired with a single-cylinder research engine equipped with an insulated piston face. An intake preheat temperature of 250 °C was shown to provide the best combination of ignition delay and engine performance. A sweep of equivalence ratio then demonstrated soot emissions close to or below the current regulatory limit and combustion efficiencies greater than 96% up to stoichiometric fuel loadings. However, both soot emissions and combustion efficiency were worse than expected at low fuel loadings, and cycle-to-cycle variability was high throughout. Schlieren imaging and numerical investigation of the injection process demonstrate oscillatory dynamics and poor control over the end of injection. This indicates that further improvements to performance and emissions could be made by developing purpose-built gaseous fuel injectors. However, even with coarse control over injection, the improvements in particulate emissions over number 2 Diesel fuel and potential for stoichiometric operation-enabling NOx control using a three-way catalyst-make a strong case for further investigation and refinement.
CitationOliver, N. and Edwards, C., "Realizing Stoichiometric, Natural Gas-Fueled Combustion in Diesel Engines," SAE Technical Paper 2018-01-1148, 2018, https://doi.org/10.4271/2018-01-1148.
- Boyer, R., “Status of Dual Fuel Engine Development,” SAE Technical Paper 490018, 1949, doi:10.4271/490018.
- Karim, G., “A Review of Combustion Processes in the Dual Fuel Engine-The Gas Diesel Engine,” Progress in Energy and Combustion Science 6(3):277-285, 1980, doi:10.1016/0360-1285(80)90019-2.
- Papagiannakis, R., Rakapoulos, C., Hountalas, D., and Rakopoulos, D., “Emission Characteristics of High Speed, Dual Fuel, Compression Ignition Engine Operating in a Wide Range of Natural Gas/Diesel Fuel Proportions,” Fuel 89(7):1397-1406, 2010, doi:10.1016/j.fuel.2009.11.001.
- Draper, R., Lenski, B., Foltz, F., Beazley, R. et al., “Measured and Predicted Performance of a Downsized, Medium Duty, Natural Gas Engine,” SAE Technical Paper 20017-01-0775, 2017, doi:104271/2017-01-0775.
- Zoldak, P. and Naber, J., “Spark Ignited Direct Injection Natural Gas Combustion in a Heavy Duty Single Cylinder Test Engine - Nozzle Included Angle Effects,” SAE Technical Paper 2017-01-0781, 2017, doi:10.4271/2017-01-0781.
- Harrington, J., Munshi, S., Nedelcu, C., Ouellette, P. et al., “Direct Injection of Natural Gas in a Heavy-Duty Diesel Engine,” SAE Technical Paper 2002-01-01630, 2002, doi:10.4271/2002-01-1630.
- Willi, M. and Richards, B., “Design and Development of a Direct Injected, Glow Plug Ignition-Assisted, Natural Gas Engine,” Journal of Engineering for Gas Turbines and Power 117(4):799-803, 1995, doi:10.1115/1.2815467.
- Fraser, R., Sieber, D., and Edwards, C., “Autoignition of Methane and Natural Gas in a Simulated Diesel Environment,” SAE Technical Paper 910227, 1991, doi:10.4271/910227.
- Johnson, B. and Edwards, C., “Exploring the Pathway to High Efficiency IC Engines through Exergy Analysis of Heat Transfer Reduction,” SAE Int. J. Engines 6(1):150-166, 2013, doi:104271/2013-01-0278.
- Roberts, G., Johnson, B., and Edwards, C., “Prospects for High-Temperature Combustion, Neat Alcohol-Fueled Diesel Engines,” SAE Int. J. Engines 7(1):448-457, 2014, doi:10.4271/2014-01-1194.
- Johnson, B., “Exploring the Pathway to High-Efficiency, High-Power IC Engines Through Exergy Analysis and Stoichiometric Direct Injection,” Ph.D. thesis, Department of Mechanical Engineering, Stanford University, 2015.