This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Parametric Study and Prediction of Lubrication Oil Film Thickness in Sliding and Rolling Interface Valve Trains
Technical Paper
2018-01-0931
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
To achieve acceptable valve train lubrication with low viscosity oil is challenging. Understanding the effect of valve train design parameter on valve train lubrication is important. In this study rocker arm valve train mechanism is analyzed to check the influence of valve train design parameters on lubrication at cam and rocker face interface. In valve train lubrication, lubrication oil film thickness play important role in valve train wear and friction. Main objective is to maintain acceptable oil film thickness at peak valve lift and minimizing the duration of critical minimum oil film thickness at cam flank to avoid wear at cam/ roller rocker follower interface when using low viscosity oil. Cam nose wear effect the engine performance and wear at cam flank change the dynamic characteristics of valve train.
Lubrication oil entrainment velocity is an important parameter controlling the lubrication oil film thickness in elasto hydrodynamic lubrication zone at cam / roller rocker interface. Lubrication oil film thickness is proportional to lubrication entrainment velocity. High entrainment velocity is better for high lubrication oil film thickness. Valve train design parameters including contact geometry at cam rocker interface mainly control the entrainment velocity. Entrainment velocity also increases with engine operating RPM.
This study is done using 1-D multi body dynamics simulation tools to quantify the effect of type of contact at cam / rocker face interface (slider and roller), valve train design parameter (cam base circle radius, roller radius) and different grade lubrication oil on lubrication oil film thickness which influences the friction and wear of valve train. Simulation methodology is developed to predict tribology behavior at cam / rocker face contact point.
Recommended Content
| Technical Paper | Effect of Unleaded Fuel on Lubricant Performance |
| Journal Article | Highly Efficient Lubricant for Sport Motorcycle Application - Fuel Economy and Durability Testing |
Authors
Topic
Citation
Poonia, S., Singh, A., Singh, J., Kumar, N. et al., "Parametric Study and Prediction of Lubrication Oil Film Thickness in Sliding and Rolling Interface Valve Trains," SAE Technical Paper 2018-01-0931, 2018, https://doi.org/10.4271/2018-01-0931.Also In
References
- de Paula Pignatti , T.T. , Miziara , W. , and de Cunha , R. Reduced Friction for a Four Cylinder Two Valve Otto Engine Valve Train SAE Technical Paper 2011-36-0208 2011 10.4271/2011-36-0208
- Wang , Y. Introduction to Engine Valve Trains SAE International Warrendale, PA 2007
- Chen , F.Y. Mechanics and Design of Cam Mechanisms Pergamon Press 1982
- Katoh , A. and Yasuda , Y. An Analysis of Friction Reduction Techniques for the Direct-Acting Valve Train System of a New-Generation Lightweight 3-Liter V6 Nissan Engine SAE Technical Paper 940992 1994
- Beloiu , D.M. Modeling and Analysis of Valve Train, Part I -Conventional Systems SAE Technical Paper 2010-01-1198 10.4271/2010-01-1198
- Hooke , C. The Minimum Film Thickness in Lubricated Line Contacts during a Reversal of Entrainment-General Solution and the Development of a Design Chart Proc. Inst.Mech. Eng, Part J: J. Eng. Tribol. 208 53 64 1994
- Kreuter , P. and Pischinger , F. Valve Train Calculation Model with Regard to Oil Film Effects SAE Technical Paper 850399 1985 https://doi.org/10.4271/850399
- Hamrock , B.J. and Dowson , D. Isothermal Elastohydrodynamic Lubrication of Point Contacts: Part III-Fully Flooded Results Journal of Lubrication Technology 99 2 264 276 1977
- Wedeven , L.E. , Evans , D. , and Cameron , A. Optical Analysis of Ball Bearing Starvation Journal of Lubrication Technology 93 3 349 363 1971
- Wolveridge , P.E. , Baglin , K.P. , and Archard , J.F. The Starved Lubrication of Cylinders in Line Contact Proc. Inst. Mech. Eng. 185 1159 1971
- Hamrock , B.J. and Dowson , D. Isothermal Elastohydrodynamic Lubrication of Point Contacts: Part IV-Starvation Results Trans. ASME, J. Lubr. Technol. 99 1 15 23 1977
- Greenwood , J.A. and Tripp , J.H. The Contact of Two Nominally Flat Rough Surfaces Proc Inst Mech Engrs 1970-71 185 48 625 633 1970
- AVL LIST GmbH v2016 2016