This content is not included in your SAE MOBILUS subscription, or you are not logged in.
A Uniform Hardware-in-the-Loop Test Rig for Modular and Integrated Testing of Commercial Vehicle Electronic Braking System
ISSN: 0148-7191, e-ISSN: 2688-3627
Published September 27, 2016 by SAE International in United States
Annotation ability available
This paper describes a uniform Hardware-In-the-Loop (HiL) test rig for the different types of Electronic Braking System (EBS). It is applied to both modular testing and integrated testing.
This test rig includes a vehicle dynamic model, a real-time simulation platform, an actual brake circuit and the EBS system under test.
Firstly, the vehicle dynamic model is a highly parameterized commercial vehicle model. So it can simulate different types of commercial vehicle by different parameter configurations. Secondly, multi-types of brake circuit are modeled using brake components simulation library. So, it can test the EBS control unit independently without the influence of any real electro-pneumatic components. And a software EBS controller is also modeled. So it can test the algorithm of EBS offline. Thirdly, all real electro-pneumatic components without real gas inputted are connected to the real-time test platform through independent program-controlled relay-switches. So it can help to test the electro-pneumatic module independently without the influence of EBS control unit and real gas. Fourthly, all real components of the brake system with real gas driven are connected to the real-time platform through program-controlled relay-switches. So the integrated system can be tested. Finally top-level GUI is designed to let the test rig run at the right configuration and right connection for a specific test application.
CitationJiang, D., Huang, Y., Song, X., Fu, D. et al., "A Uniform Hardware-in-the-Loop Test Rig for Modular and Integrated Testing of Commercial Vehicle Electronic Braking System," SAE Technical Paper 2016-01-8042, 2016, https://doi.org/10.4271/2016-01-8042.
- Beyer, C., Schramm, H., and Wrede, J., "Electronic Braking System EBS - Status and Advanced Functions," SAE Technical Paper 982781, 1998, doi:10.4271/982781.
- Schuette, H. and Waeltermann, P., "Hardware-in-the-Loop Testing of Vehicle Dynamics Controllers - A Technical Survey," SAE Technical Paper 2005-01-1660, 2005, doi:10.4271/2005-01-1660.
- Bauer, F. and Fleischhacker, J., "Hardware-in-the-Loop Simulation of Electro-Pneumatic Brake Systems," SAE Technical Paper 2015-01-2745, 2015, doi:10.4271/2015-01-2745.
- Weiqiang, Z., Zong, C., Zheng, H., Wang, H. et al., "Integrated HIL Test and Development System for Pneumatic ABS/EBS ECU of Commercial Vehicles," SAE Technical Paper 2012-01-2031, 2012, doi:10.4271/2012-01-2031.
- Niglas, P., "An Analysis of Braking Performance Using Hardware in the Loop Simulation," SAE Technical Paper 2013-01-2352, 2013, doi:10.4271/2013-01-2352.
- Zhang, D., Zong, C., Wan, Y., Zheng, H. et al., "Development and Research on Control Strategy of Advanced Electronic Braking Systems for Commercial Vehicle," SAE Technical Paper 2014-01-2285, 2014, doi:10.4271/2014-01-2285.
- Selvaraj, M., Gaikwad, S., and Suresh, A., "Modeling and Simulation of Dynamic Behavior of Pneumatic Brake System at Vehicle Level," SAE Technical Paper 2014-01-2494, 2014, doi:10.4271/2014-01-2494.
- Mithun, S., Mariappa, S., Gayakwad Suresh., “Modeling and simulation of pneumatic brake system used in heavy commercial vehicle” IOSR, Journal of Mechanical and civil Engineering doi:10.9790/1684-11120109
- The International Organisation for Standardisation (ISO), “Pneumatic fluid power - Determination of flow-rate characteristics of components using compressible fluids - Part 1: General rules and test methods for steady-state flow,” ISO 6358, 2013.
- Zhiquan, F., “The Design and application of air ABS Hardware-in-the-loop Simulation System”, Master thesis, Department of Automotive Engineering, Tsinghua University, Beijing, 2003.
- Yanli, H., “Study on the Dynamic Characteristics of Pneumatic ABS Solenoid Valve for Commercial Vehicle”, Master thesis, Department of Automotive Engineering, Jilin University, Changchun, 2007.