This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
High Power Discharge Combustion Effects on Fuel Consumption, Emissions, and Catalyst Heating
Technical Paper
2014-01-2626
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
A key element to achieving vehicle emission certification for most light-duty vehicles using spark-ignition engine technology is prompt catalyst warming. Emission mitigation largely does not occur while the catalyst is below its “light-off temperature”, which takes a certain time to achieve when the engine starts from a cold condition. If the catalyst takes too long to light-off, the vehicle could fail its emission certification; it is necessary to minimize the catalyst warm up period to mitigate emissions as quickly as possible. One technique used to minimize catalyst warm up is to calibrate the engine in such a way that it delivers high temperature exhaust. At idle or low speed/low-load conditions, this can be done by retarding spark timing with a corresponding increase in fuel flow rate and / or leaning the mixture. Both approaches, however, encounter limits as combustion stability degrades and / or nitrogen oxide emissions rise excessively. Such limits are inevitable but also seem to be influenced by the type of ignition technology.
One ignition technology that may improve the limits of advanced ignition timing and leaned mixture for low-load catalyst warming is pulsed energy ignition technology. In other studies, this technology is shown to improve engine fuel consumption and combustion stability at low load and idle conditions. Further, with controlled combustion bomb studies, the technology shows shorter ignition and flame development periods, thus suggesting the possibility to ignite “more difficult” combustion mixtures (such as low-turbulent kinetic energy or lean mixtures). Such data supported the pursuit of the current study, which has the objectives to determine the potential improvement in combustion stability, exhaust heat flow, and emissions during low-load catalyst warming operation of a spark-ignition engine. This article highlights the study and provides data showing combustion stability, emissions, and exhaust heat flux behavior as ignition timing and fuel mixture strength vary for two different plugs: a conventional spark plug and a pulsed energy plug. The study reveals the pulsed energy ignition technology can increase exhaust heat flux by 6% for similar combustion stability criterion (less than 15% IMEP-COV for catalyst heating strategy) with marginal penalty in fuel consumption and unburned hydrocarbon emissions when compared to conventional spark plug technology.
Recommended Content
Authors
Topic
Citation
Jacobs, T., Camilli, L., and Neubauer, M., "High Power Discharge Combustion Effects on Fuel Consumption, Emissions, and Catalyst Heating," SAE Technical Paper 2014-01-2626, 2014, https://doi.org/10.4271/2014-01-2626.Also In
References
- Kubo , S. , Yamamoto , M. , Kizaki , Y. , Yamazaki , S. et al. Speciated Hydrocarbon Emissions of SI Engine During Cold Start and Warm-up SAE Technical Paper 932706 1993 10.4271/932706
- Ball , D. A Warm-Up - Underfloor Converter Parametric Study: Effects of Catalyst Technology on Emission Performance SAE Technical Paper 961905 1996 10.4271/961905
- Ueno , M. , Akazaki , S. , Yasui , Y. , and Iwaki , Y. A Quick Warm-Up System During Engine Start-Up Period Using Adaptive Control of Intake Air and Ignition Timing SAE Technical Paper 2000-01-0551 2000 10.4271/2000-01-0551
- Hallgren , B. and Heywood , J. Effects of Substantial Spark Retard on SI Engine Combustion and Hydrocarbon Emissions SAE Technical Paper 2003-01-3237 2003 10.4271/2003-01-3237
- Twiney , B. , Stone , R. , Chen , X. , and Edmunds , G. Investigation of Combustion Robustness in Catalyst Heating Operation on a Spray Guided DISI Engine, Part 1 - Measurements of Spark Parameters and Combustion SAE Technical Paper 2010-01-0593 2010 10.4271/2010-01-0593
- Miyashita , N. , Matsubara , Y. , Iwata , K. , and Ishikawa , M. Spark Plugs for Gasoline Direct Injection Engines SAE Technical Paper 2001-01-1200 2001 10.4271/2001-01-1200
- Hori , T. , Shibata , M. , Okabe , S. , and Hashizume , K. Super Ignition Spark Plug with Fine Center & Ground Electrodes SAE Technical Paper 2003-01-0404 2003 10.4271/2003-01-0404
- Griswold , J.E. , Corio R.P. , and Pate R.C. Combustion ignitor U.S. Patent 5,371,436 1994 United States
- Camilli , L.S. Current peaking sparkplug U.S. Patent 6,329,743 2001 United States
- Rohwein , G. and Camilli , L. Automotive Ignition Transfer Efficiency SAE Technical Paper 2002-01-2839 2002 10.4271/2002-01-2839
- Camilli , L. Personal Communication with Sandia National Laboratories 1992
- Camilli , L. , Gonnella , J. , and Jacobs , T. Improvement in Spark-Ignition Engine Fuel Consumption and Cyclic Variability with Pulsed Energy Spark Plug SAE Technical Paper 2012-01-1151 2012 10.4271/2012-01-1151
- Jacobs , T.J. , Camilli L.J. , and Gonnella J.E. Improvement in lean homogenous spark-ignition combustion with pulsed energy spark plug ASME 2012 Internal Combustion Engine Division Fall Technical Conference 2012 Vancouver, BC
- Russ , S. , Thiel , M. , and Lavoie , G. SI Engine Operation with Retarded Ignition: Part 2 -HC Emissions and Oxidation SAE Technical Paper 1999-01-3507 1999 10.4271/1999-01-3507