This content is not included in your SAE MOBILUS subscription, or you are not logged in.
Multi-Body Dynamic Simulation and Experimental Validation of Valve Spring Surge Speed
ISSN: 0148-7191, e-ISSN: 2688-3627
Published November 27, 2013 by SAE International in United States
Annotation ability available
Event: 8th SAEINDIA International Mobility Conference & Exposition and Commercial Vehicle Engineering Congress 2013 (SIMCOMVEC)
Valve spring surge is one of the critical issues in an automotive engine that may cause catastrophic failure in an engine. The term surge refers to inter coil vibration of valve spring, which occurs when the natural frequency of the spring matches with the engine operating frequency. This surge happens when the engine speeds-up beyond the design limit under certain extreme operating conditions. The speed at which the valve spring surges is referred as valve spring surge speed. At this speed, the spring force starts deteriorating and eventually results in loss of contact between the valve train components. So, there is a need to predict the engine speed at which the valve-train components start losing contact and also explore possibilities to increase the surge speed by optimizing the valve spring design parameters. This paper is a physical extension of theoretical prediction of valve jump phenomenon for existing and proposed valve springs using multi-body dynamic ADAMS software® .
In this paper, a non-fired version of H-series, 6 cylinders, TCI, Inline engine is taken up to experimentally measure the valve spring surge speeds with existing and proposed valve springs on a multi-functional test-rig. The proposed design points to an increase of approximately 200-300 rpm in surge speed, which amounts to an increase of seven percent. The experimental findings are compared with the simulation results and it is noted that there is a close correlation is observed between the simulation and experimental results. Simulation and experimental results for both existing and proposed springs correlate to within eight percent. Since the proposed valve spring has a higher surge speed as compared to the existing one, the valve-train failures in the field are expected to reduce significantly.
CitationPrabakar, R., Nagar, A., patil, M., N, U. et al., "Multi-Body Dynamic Simulation and Experimental Validation of Valve Spring Surge Speed," SAE Technical Paper 2013-01-2770, 2013, https://doi.org/10.4271/2013-01-2770.
- Choi T. D., Eslinger O. J., Kelley C. T., David J. W., Etheridge M., “Optimization of Automotive Valve-train Components with Implicit Filtering”, Optimization and Engineering, Volume 1, Issue 1, pp 9-27 (2000).
- Xi Ping Yuan, Zhu Jiang, “Simulated Annealing Optimization on Valve Spring of Diesel Engine”, Applied Mechanics and Materials, Vols. 63-64, 511 (2011).
- Prabakar, R. and Mangalaramanan, S., “Flexible Multi-Body Dynamic Analysis of Multi-Cylinder Engine Valve Train,” SAE Technical Paper 2011-26-0086, 2011, doi:10.4271/2011-26-0086.
- En'guo Dong, Zhang Lei. “Robust design of valve spring based on Taught method”, 2nd International Conference on Electronic and Mechanical Engineering and Information Technology (2012).
- Kushwaha H., Rahnejat H and Jin Z M, “Valve-train dynamics: a simplified tribo-elasto-multi-body analysis”, Proc. Instn.MechEngrs Part K, 214, 95-110 (2000).
- Teodorescu M., Kushwaha M, Rahnejat H and Taraza D, “Elastodynamic transient analysis of a four-cylinder valvetrain system with camshaft flexibility”, Proc. IMechE Part K: Journal of Multi-body Dynamics, 219, 13-25 (2005).
- Fujimoto A., Higashi H., Osawa N., Nakai H. and Mizukami T., “Valve jump prediction using dynamic simulation on direct acting valve-train”, Mitsubishi Motors Technical Review, No. 19, 19-23 (2007).
- Liu H and Kim D., “Effects of end coils on the natural frequency of automotive engine valve springs”, International Journal of Automotive Technology, 10 (4), 413-420 (2009).