This content is not included in your SAE MOBILUS subscription, or you are not logged in.
Multidimensional Optimization of DI Diesel Engine Process Using Multi-Zone Fuel Spray Combustion Model and Detailed Chemistry NOx Formation Model
ISSN: 0148-7191, e-ISSN: 2688-3627
Published April 08, 2013 by SAE International in United States
Annotation ability available
A previously developed multi-zone direct-injection (DI) diesel combustion model was implemented into a turbocharged diesel engine full cycle simulation tool DIESEL-RK. The combustion model takes into account the following features of the spray dynamics:
- Detailed evolution process of fuel sprays.
- Interaction of sprays with the in-cylinder swirl and the walls of the combustion chamber.
- Evolution of a Near-Wall Flow (NWF) formed as a result of a spray-wall impingement as a function of the impingement angle and the local swirl velocity.
- Interaction of Near-Wall Flows formed by adjacent sprays.
- Effect of gas and wall temperatures on the evaporation rate in the spray and NWF zones.
In the model each fuel spray is split into a number of specific zones with different evaporation conditions. Zones, formed on the cylinder liner surface and on the cylinder head, are also taken into account. The piston bowl in the modeling process is assumed to have an arbitrary axi-symmetric shape. The combustion model supports central, non-central and side injection systems. A NOx calculation sub-model uses detailed chemistry analysis which considers 199 reactions of 33 species. The soot formation calculation sub-model used is a phenomenological one and takes into account the distribution of the droplets Sauter Mean Diameter (SMD) during the injection process. The ignition delay period is estimated using relevant data in the pre-calculated comprehensive 4-D map of ignition delays. This 4-D map is developed using CHEMKIN detailed chemistry simulations and takes into account effects of the temperature, the pressure, the Fuel/Air ratio and the Exhaust Gas Recirculation (EGR).
The noted above sub-models were integrated into full-cycle engine simulation software together with library of non-linear programming procedures, allowing multidimensional optimization of DI diesel engine working parameters to reach prescribed emissions regulations norms. List of optimized parameters includes: CR, EGR, injection profile shape, fuel injection pressure, port timings (IVC), boost pressure, power for turbocharger assistance, injection timing, nozzles hole number, diameter and inclination angle of nozzles. Two variants of piston bowl were investigated. In the research there was done an optimization of working parameters of medium speed diesel engine at few operating points with account of weighting coefficients of the points. At each operating point the problem of optimization has individual peculiarities and an individual set of independent variables and restrictions. The expression for objective function of conjoint optimization of SFC, NOx and PM was proposed. Procedures of Rosenbrock, Powell and other were used for optimum search. Restrictions were accounted by penalty function method. Controlling algorithms for EGR booster driving, injection timing, Common Rail pressure, turbocharger assist for locomotive performance were obtained. To provide a required injection profile shape being obtained in optimization a modification of injector was carried out. There were optimized fuel pipe line diameter and dimensions of internal elements of injector: control valve, orifice and internal volume. The injection profile was simulated with hydrodynamic simulation software INJECT.
|Journal Article||Preliminary Design of a Two-Stroke Uniflow Diesel Engine for Passenger Car|
|Technical Paper||A New Datadriven Approach to Modeling the Combustion of a Diesel Engine in HCCI Mode|
CitationKuleshov, A. and Grekhov, L., "Multidimensional Optimization of DI Diesel Engine Process Using Multi-Zone Fuel Spray Combustion Model and Detailed Chemistry NOx Formation Model," SAE Technical Paper 2013-01-0882, 2013, https://doi.org/10.4271/2013-01-0882.
Modeling of SI and Diesel Engines, 2013
Number: SP-2344; Published: 2013-04-09
Number: SP-2344; Published: 2013-04-09
- Dohle U. MTU solutions for meeting future exhaust emissions regulations Paper No. 284, CIMAC Congress 2010 Bergen 8
- Koch F. , Seidl T. , Schnitzer O. , Oehler G. , Loettgen A. , Loeser S. Development strategies for high speed marine diesel engines Paper No. 248, CIMAC Congress 2010 Bergen 9
- Hopmann U. Development of the new Caterpillar VM32C LE low emission engine Paper No. 302, CIMAC Congress 2010 Bergen 7
- Schlemmer-Kelling U. The Environment Friendly Medium Speed Engine Paper No. 32, CIMAC Congress 2007 Vienna 10
- Kendlbacher C. , Müller P. , Bernhaupt M. , Rehbichler G. Large engine injection systems for future emission legislations Paper No. 50, CIMAC Congress 2010 Bergen 11
- Heim K. , Troberg M. , Ollus R. , Vaarasto M. Latest developments in Wärtsilä's medium-speed engine portfolio Paper No. 206, CIMAC Congress 2010 Bergen 14
- Ludu Andrei , Engelmayer Michael , Pemp Bernhard , Foelzer Karl Heinz , Bouche Thomas , Lustgarten George Large high speed diesels, quo vadis? Superior system integration, the answer to the challenge of the 2012 - 2020 emission limits Paper No. 313, CIMAC Congress 2010 Bergen 2010 14
- Ehleskog , M. , Gjirja , S. , and Denbratt , I. Effects of High Injection Pressure, EGR and Charge Air Pressure on Combustion and Emissions in an HD Single Cylinder Diesel Engine SAE Int. J. Engines 2 2 341 354 2010 10.4271/2009-01-2815
- Kuleshov , A. Model for Predicting Air-Fuel Mixing, Combustion and Emissions in DI Diesel Engines over Whole Operating Range SAE Technical Paper 2005-01-2119 2005 10.4271/2005-01-2119
- Kuleshov , A. Multi-Zone DI Diesel Spray Combustion Model for Thermodynamic Simulation of Engine with PCCI and High EGR Level SAE Int. J. Engines 2 1 1811 1834 2009 10.4271/2009-01-1956
- Kuleshov , A. , Kozlov , A. , and Mahkamov , K. Self-Ignition Delay Prediction in PCCI Direct Injection Diesel Engines Using Multi-Zone Spray Combustion Model and Detailed Chemistry SAE Technical Paper 2010-01-1960 2010 10.4271/2010-01-1960
- Kuleshov , A. Use of Multi-Zone DI Diesel Spray Combustion Model for Simulation and Optimization of Performance and Emissions of Engines with Multiple Injection SAE Technical Paper 2006-01-1385 2006 10.4271/2006-01-1385
- Kuleshov , A. Multi-Zone DI Diesel Spray Combustion Model and its application for Matching the Injector Design with Piston Bowl Shape SAE Technical Paper 2007-01-1908 2007 10.4271/2007-01-1908
- Kuleshov A.S. Development of simulation methods and optimization of working processes of ICE Autoref. Diss. Doct. Tech. Sc. - Moscow 2011
- Bochkov M.V. , Zaharov A.U. , Hvisevich S.N. NOx formation at combustion of methane-air mixture in conditions of simultaneous processes of chemical kinetic and molecular diffusion Mathematical modeling 1997 9 3 13 28
- Grekhov L.V. , Ivaschenko N.F. , Markov V.F. Fuel systems and diesel control Moscow Legion-Autodata 2005 344
- Montgomery , D. and Reitz , R. Optimization of Heavy-Duty Diesel Engine Operating Parameters Using A Response Surface Method SAE Technical Paper 2000-01-1962 2000 10.4271/2000-01-1962
- Desantes , J. , López , J. , García , J. , and Hernández , L. Application of Neural Networks for Prediction and Optimization of Exhaust Emissions in a H.D. Diesel Engine SAE Technical Paper 2002-01-1144 2002 10.4271/2002-01-1144